Ambient Weather WS-2063 User manual

Version 1.0 ©Copyright 2016, Ambient LLC. All Rights Reserved. Page 1
Ambient Weather WS-2063 Indoor Temperature and
Humidity Monitor with Backlight User Manual
Table of Contents
1. Introduction.....................................................................................................................................1
2. Getting Started ................................................................................................................................2
2.1 Monitor Features ....................................................................................................................2
2.2 Parts List.................................................................................................................................3
2.3 Powering Up...........................................................................................................................3
3. Monitor Display..............................................................................................................................3
3.1 Temperature Display ..............................................................................................................3
3.2 Humidity Display...................................................................................................................3
4. Specifications and Accuracy...........................................................................................................4
4.1 Measurement Specifications.........................................................................................................4
4.2 Power Consumption......................................................................................................................4
5. Troubleshooting Guide....................................................................................................................5
6. Liability Disclaimer ........................................................................................................................5
7. Warranty Information......................................................................................................................6
1. Introduction
Thank you for your purchase of the Ambient Weather WS-2063 Indoor Temperature and Humidity
Monitor with Backlight. The following user guide provides step by step instructions for installation,
operation and troubleshooting. To download the latest full sized manual and additional
troubleshooting tips, please visit:
http://ambientweather.wikispaces.com/ws2063

Version 1.0 ©Copyright 2016, Ambient LLC. All Rights Reserved. Page 2
2. Getting Started
2.1 Monitor Features
Figure 1
No
Description
No
Description
1
LIGHT Button. Press to turn on the back
light for 5 seconds.
7
OUT TEMP sensor (optional) jack.
2
IN/ OUT button.
- When the optional probe is connected,
press to switch between the indoor and
probe temperature.
- Press and hold for 2 seconds to scroll
between indoor and probe temperature
automatically every 5 seconds. Press
again to stop the scroll mode.
8
NIGHT ON/OFF slide switch.
Slide to the ON position to activate the
night light feature.
- When the switch is ON, the backlight will
turn on automatically when the room is
dim or dark.
- Slide to OFF to turn the backlight feature
off.
3
CHECK/RESET button.
- Press to instantly check the current
temperature, humidity and low battery.
- Press and hold for 2 seconds to reset the
minimum and maximum data.
9
°C / °F button
- Press it to switch between Celsius and
Fahrenheit.
4
LCD Display
10
RESET button
- Press to restore to default values.
- Press to begin 24 hour minimum and
maximum timer.
5
MANUAL/Past 24hr slide switch.
- Slide to MANUAL to record the
minimum and maximum between manual
resets.
- Slide to Past 24hr to record the
minimum and maximum every 24 hours
(based on power up or manual reset).
11
Battery compartment
6
OUT TEMP sensor (optional)
12
Suspension eye for mounting to a wall.

Version 1.0 ©Copyright 2016, Ambient LLC. All Rights Reserved. Page 3
No
Description
No
Description
- Plug in the optional probe to measure
the probe temperature.
2.2 Parts List
QTY
Item
1
Monitor
Frame Dimensions: 2.8(W) x 4.05(H) x 1.06(D) in
1
User Manual
2.3 Powering Up
1. Remove the battery door on the top of the monitor and insert 2 new AA batteries, according to
the polarity information marked on the battery compartment, and replace the battery door.
2. Once the batteries are inserted, all of the LCD segments will light up briefly.
3. The 24 hour timer will begin for resetting the minimum and maximum temperature and
humidity.
4. Allow a few minutes for temperature to stabilize, and approximately 20 minutes for the
humidity to stabilize.
3. Monitor Display
3.1 Temperature Display
When you plug in the optional temperature probe, the display will automatically switch to the probe
temperature.
When the temperature is below -40°F, the icon LO appears on display.
When the temperature is above 158°F, the icon HI appears on display.
Figure 2
3.2 Humidity Display
The house humidity icon identifies high and low humidity conditions.
When the relative humidity is less than 30%, LOW is displayed.
When the relative humidity is between 30% and 50%, this is considered in the good range.
When the humidity is greater than 50%, HIGH is displayed.

Version 1.0 ©Copyright 2016, Ambient LLC. All Rights Reserved. Page 4
Figure 3
A healthy humidity level is one that measures between 30% and 50%. Humidity that measures above
50% creates a breeding ground for mold, dust mites, bacteria, and other pests. Humidity that measures
below 30% increases the likelihood that cold and flu viruses will spread while also leading to
uncomfortable respiratory symptoms. Too-dry air can also cause damage to your home's foundation
and certain furnishings. To avoid the problems of too little or too high humidity, we recommend you
maintain a humidity level of between 45% and 50%.
4. Specifications and Accuracy
4.1 Measurement Specifications
The following table provides specifications for the measured parameters.
Measurement
Range
Accuracy
Resolution
Indoor Temperature
32 to 113 °F
± 2 °F
0.1
Probe Temperature
-4 to 140 °F
± 2 °F
0.1
Humidity
1 to 99%
± 5% of full scale
between 10 and 95%
1
4.2 Power Consumption
Monitor: 2 x AAAlkaline batteries recommended.

Version 1.0 ©Copyright 2016, Ambient LLC. All Rights Reserved. Page 5
5. Troubleshooting Guide
If your question is not answered here, you can contact us as follows:
1. Email Support: [e-mail]
2. Technical Support: 480-346-3380 (M-F 8am to 4pm Arizona Time)
Problem
Solution
Humidity is inaccurate
Humidity is a difficult parameter to measure electronically and drifts over
time due to contamination. Even the most expensive hygrometers are only
accurate to ± 3% of full scale.
In addition, location has an adverse effect on humidity readings. Note that
indoor and outdoor humidity varies greatly indoors, outdoors and location to
location, so you cannot accurately compare your humidity to official
weather station sources, such as the news or National Weather Service.
Use a calibrated source, such as a sling psychrometer for comparison.
Temperature is
inaccurate
Temperature errors can occur when a sensor is placed too close to a heat
source. To verify temperature accuracy, we recommend a mercury or red
spirit (fluid) thermometer. Bi-metal (dial thermometers
or thermostats) and other digital thermometers are not a good source and
have their own margin of error.
Display is dim
Replace the batteries.
Monitor locks up or
exhibits unusual
operation
Press the reset button.
6. Liability Disclaimer
Please help in the preservation of the environment and return used batteries to an authorized depot.
The electrical and electronic wastes contain hazardous substances. Disposal of electronic waste in
wild country and/or in unauthorized grounds strongly damages the environment.
Reading the “User manual” is highly recommended. The manufacturer and supplier cannot accept any
responsibility for any incorrect readings and any consequences that occur should an inaccurate reading
take place.
This product is designed for use in the home only as indication of weather conditions. This product is
not to be used for medical purposes or for public information.
The specifications of this product may change without prior notice.
This product is not a toy. Keep out of the reach of children.
No part of this manual may be reproduced without written authorization of the manufacturer.
Ambient, LLC WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL,
PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT.

Version 1.0 ©Copyright 2016, Ambient LLC. All Rights Reserved. Page 6
7. Warranty Information
Ambient, LLC provides a 1-year limited warranty on this product against manufacturing defects in
materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased and
only to the original purchaser of this product. To receive warranty service, the purchaser must contact
Ambient, LLC for problem determination and service procedures.
Warranty service can only be performed by a Ambient, LLC. The original dated bill of sale must be
presented upon request as proof of purchase toAmbient, LLC.
Your Ambient, LLC warranty covers all defects in material and workmanship with the following
specified exceptions: (1) damage caused by accident, unreasonable use or neglect (lack of reasonable
and necessary maintenance); (2) damage resulting from failure to follow instructions contained in your
owner’s manual; (3) damage resulting from the performance of repairs or alterations by someone other
than an authorized Ambient, LLC authorized service center; (4) units used for other than home use (5)
applications and uses that this product was not intended (6) the products inability to receive a signal
due to any source of interference or metal obstructions and (7) extreme acts of nature, such as
lightning strikes or floods.
This warranty covers only actual defects within the product itself, and does not cover the cost of
installation or removal from a fixed installation, normal set-up or adjustments, claims based on
misrepresentation by the seller or performance variations resulting from installation-related
circumstances.