Ambient Weather TESA WS710 User manual

Table of Contents
…………………………..……….……………………….....2
.……….……………………………...............................2
……….…………………………......…………………...2
……….……………………………..…..…..…..2
.……….………………….....2
……….………………………...…..…….5
.……….………………….…….......6
……….……………………....7
……….………………......…………….......8
……….……………………………...…...…...…….....8
….……………………………......…………...............8
………………………....….….….……......8
……….…………………………………………….8
……….……………………………………….
...…….…………..……...........9
....……………. ....………. …9
……….…………………….…......……….9
… … ...… … … … .9
… … .… … … … … … .… … ......… … 10
……….……...……………......…….11
…….….……………......…… … 11
… … … .… … .....… … … ...................… … … .12
……….…………………………....………………….12
……….……......………………......…….12
… ...… .… … … … … ......… … .12
… … … .… … … … … … ......… … … .… … 13
….........……………………….…….………13
1. Introduction
2.Getting Started
2.1 Parts List
2.2 Recommend Tools
2.3 Thermo-Hygrometer Sensor Set Up
2.4 Display Console Set Up
2.4.1 Display Console Layout
2.4.2 Sensor Operation Verification
3.Remote Sensor Installation
4.Display Features
4.1 Comfort Icon
4.2 Rate of Change Icon
5.Console Operation
5.1 Min/Max Mode ........8
5.2 Indoor/Outdoor Channel Selection
5.3 Temperature Units of Measure ... ...
5.4 Sensor Search Mode
5.5 Best Practices for Wireless Communication
5.6 Adjustment or Calibration
5.6.1 Humidity Calibration
5.6.2 Temperature Calibration
6.Glossary of Terms
7.Specifications
7.1 Wireless Specifications
7.2 Measurement Specifications
7.3 Power Consumption
8.Troubleshooting Guide
WS710 Wireless Indoor/Outdoor 8-Channel
Thermo-Hygrometer with Daily Min/Max Display
INSTRUCTION MANUAL
-1-

1. Introduction
Thank you for your purchase of the WS710 Wireless Indoor/Outdoor
8-Channel Thermo-Hygrometer with Jumbo Display. The following user
guide provides step by step instructions for installation, operation and
troubleshooting.
2.Getting Started
Note: The power up sequence must be performed in the order
shown in this section (insert batteries in the remote transmitter(s) first,
Display Console second).
The unit consists of a display console (receiver), and a thermo-
hygrometer (remote transmitter).
2.1 Parts List
2.2 Recommend Tools
Hammer and nail for hanging remote thermo-hygrometer transmitter.
2.3 Thermo-Hygrometer Sensor Set Up
1. Remove the battery door on the back of the sensor by
removing the set screw, as shown in Figure 1 .
QTY Item
Display Console
Frame Dimensions (LxHxW): 11.4x12.7x2.5cm
LCD Dimensions (LxW): 9.5x8.9cm
LCD Segment Height: 3.2cm
Thermo-hygrometer transmitter
Dimensions (LxHxW): 11.4x5x2.0cm
1
1
-2-

LED
Figure 1
2. BEFORE inserting the batteries, locate the dip switches on
the inside cover of the lid of the transmitter.
Figure 2
setting).
Figure 2
3. Channel Number: The WS710 supports up to eight
transmitters. To set each channel number (the default is Channel 1),
change Dip Switches 1, 2 and 3, as referenced in Table 1.
4. Temperature Units of Measure: To change the transmitter
display units of measure (°F vs. °C), change Dip Switch 4, as referenced
in Table 1.
displays all four switches in the OFF position (factory default
-3-

Table 1
5. Insert two AAA batteries.
6. After inserting the batteries, the remote sensor LED indicator will
light for 4 seconds, and then flash once per 60 seconds thereafter.
Each time it flashes, the sensor is transmitting data.
7. Verify the correct channel number (CH) and temperature units of
measure (°F vs. °C) are on the display, as shown in Figure 3.
Figure 3
(1) temperature
(2) temperature units (°F vs. °C)
(3) channel number
(4) relative humidity
DIP SWITCH FUNCTION
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
°F
°C
1
2
3
4
-4-

8. Close the battery door. Make sure the gasket (around the
battery compartment) is properly seated in its trace prior to closing
the door. Tighten the set screw.
2.4 Display Console Set Up
1. Move the remote thermo-hygrometer(s) about 1.5m to 3m away
from the display console (if the sensor is too close, it may not be
received by the display console). If you have more than one
thermo-hygrometer, make sure they are all powered up and
transmitting on different channels.
2. Remove the battery door on the back of the display, as shown in
Figure 4. Insert four AAA (alkaline or lithium, avoid rechargeable)
batteries in the back of the display console
Figure 4
All of the LCD segments will light up for a few seconds to verify all
segments are operating properly.
3. Replace the battery door, and fold out the desk stand and place the
console in the upright position.
The console will instantly display indoor temperature and humidity
as designated by the icon. The remote temperature and humidity
will update on the display within a few minutes on the appropriate
channel.
-5-

While in the search mode, the remote search icon will be
constantly displayed.
If you have more than one remote sensor (up to eight remotes are
supported), the display will automatically toggle between sensors
until all sensors have reported in.
Do not touch any buttons until the remote sensor has reported in, or
the radio search icon is no longer on, otherwise the remote
sensor search mode will be terminated. When the remote sensor
temperature and humidity has been received, the console will
automatically switch to the normal mode, and all further settings can
be performed.
If the remote does not update, please reference the troubleshooting
guide in Section 8 .
2.4.1 Display Console Layout
Note: The following illustration shows the full segments of the
LCD for description purposes only and will not appear like this during
normal operation.
Figure 5
1. Temperature
2. Min/Max Record mode
1 2 3
4
5
6
7
8
9
-6-

3. Temperature, Rate of Change indicator
4. Temperature units (°F or °C)
5. Humidity, Rate of Change indicator
6. Relative Humidity (%)
7. Humidity Comfort Icon
8. Reception Icon (solid when searching, flashes when updating)
9. Channel 1,2,3,4,5,6,7,8, indicator
2.4.2 Sensor Operation Verification
Verify the indoor and outdoor humidity match closely with the console
and sensor array in the same location (about 1.5 to 3 meters apart).
The sensors should be within 10% (the accuracy is ± 5%). Allow about
30 minutes for both sensors to stabilize. The humidity can be adjusted
or calibrated later to match each other a known source.
Verify the indoor and outdoor temperature match closely with the
console and sensor array in the same location (about 1.5 to 3 meters
apart). The sensors should be within 2°C (the accuracy is ± 1°C). Allow
about 30 minutes for both sensors to stabilize. The temperature can be
adjusted or calibrated later to match each other or a known source.
3. Remote Sensor Installation
It is recommended you mount the remote sensor on a south facing
wall, in a shaded area. Direct sunlight and radiant heat sources will
result in inaccurate temperature readings. Although the sensor is water
resistant, it is best to mount in a well protected area, such as under an
eve. Use a screw or nail (not included) to affix the remote sensor to the
wall, as shown in Figure 6.
Figure 6
-7-

4. Display Features
4.1 Comfort Icon
The comfort icon is based on humidity ranges specified in Figure 7 .
The icon is displayed for indoor humidity, remote channel 1 humidity
and optional remote channels 2 through 8 humidity.
Figure 7
4.2 Rate of Change Icon
The rate of change icon detects rapid changes in temperature and
humidity. If the arrow points upward, the temperature is increasing at a
rate of +2°C per 30 minutes (or greater), or humidity is increasing at a
rate of +5% per 30 minutes (or greater). If the arrow points downward,
the temperature is decreasing at a rate of -2°C per 30 minutes (or less),
or humidity is decreasing at a rate of -5% per 30 minutes (or less).
5. Console Operation
Note: The console has three buttons for easy operation:
MIN/MAX/- button, CLEAR/ADJUST button, and CHANNEL/+ button.
5.1 Min/Max Mode
The Min/Max mode displays the minimum and maximum temperature
and humidity (since reset of the unit) for the indoor, remote channel 1
through 8 sensors.
Prior to entering the MIN/MAX mode, press the CHANNEL/+ button to
select the temperature and humidity values you wish to view.
1. Display Maximum. Press the MIN/MAX button once to display
the maximum. The MAX icon will be displayed.
2. Clear Maximum. To reset the maximum values to the current
values, press and hold the CLEAR button for 3 seconds.
RH<45% RH45%~65% RH>65%
Dry Comfortable Wet
-8-

3. Display Minimum. Press the MIN/MAX button again to
display the minimum. The MIN icon will be displayed.
4. Clear Minimum. To reset the minimum values to the current
values, press and hold the CLEAR button for 3 seconds.
To return to normal mode, press the MIN/MAX button again.
5.2 Indoor/Outdoor Channel Selection
Press the CHANNEL/+ button to switch the display between the indoor
temperature and humidity ,remote sensors 1 through 8, and scroll
mode .In scroll mode, all of the indoor and detected outdoor sensors
will be displayed in five second intervals.
5.3 Temperature Units of Measure
The default temperature units of measure are degrees Celsius. To toggle
between degrees Celsius and degrees Fahrenheit, press and hold the
MIN/MAX button for 3 seconds.
5.4 Sensor Search Mode
If any of the sensor communication is lost, dashes (--.-) will be displayed
on the screen. To reacquire the signal:
1. If a specific channel is lost, press the CHANNEL/+ button to
display this channel, then Press and hold the CHANNEL/+ button
for 3 seconds, and the remote search icon will be constantly
displayed for up to 10 minutes. Once the signal is reacquired, the
remote search icon will turn off, and the current values will be
displayed.
2. If new sensors are added, subtracted, or multiple sensor channels
are lost, press the CHANNEL/+ button until the indoor channel
is displayed. Press and hold the CHANNEL/+ button for 3
seconds, and the remote search icon will be constantly
displayed for up to 10 minutes. Once the signal is reacquired, the
remote search icon will turn off, and the current values will be
displayed.
5.5 Best Practices for Wireless Communication
Wireless communication is susceptible to interference, distance, walls
and metal barriers. We recommend the following best practices for
trouble free wireless communication.
-9-

1. Electro-Magnetic Interference (EMI). Keep the console several
feet away from computer monitors and TVs.
2. Radio Frequency Interference (RFI). If you have other 433
MHz devices and communication is intermittent, try turning off
these other devices for troubleshooting purposes. You may
need to relocate the transmitters or receivers to avoid
intermittent communication.
3. Line of Sight Rating. This device is rated at 100 meters line of
sight (no interference, barriers or walls) but typically you will get
30 meters maximum under most real-world installations, which
include passing through barriers or walls.
4. Metal Barriers. Radio frequency will not pass through metal
barriers such as aluminum siding. If you have metal siding,
align the remote and console through a window to get a clear
line of sight .
5.6 Adjustment or Calibration
Note: The calibrated value can only be adjusted on the console.
The remote sensor(s) always displays the un-calibrated or measured
value.
Note: The measured humidity range is between 10 and 99%.
Humidity cannot be accurately measured outside of this range.
The purpose of calibration is to fine tune or correct for any sensor error
associated with the devices margin of error. The measurement can be
adjusted from the console to calibrate to a known source.
Calibration is only useful if you have a known calibrated source you
can compare it against, and is optional. This section discusses
practices, procedures and sources for sensor calibration to reduce
manufacturing and degradation errors. Do not compare your readings
obtained from sources such as the internet, radio, television or
newspapers. They are in a different location and typically update once
per hour.
-10-