Ambient Weather WS-7079 User manual

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 1
Ambient Weather WS-7079 Wireless Wi-Fi Smart Weather
Station User Manual
Table of Contents
1. Introduction.....................................................................................................................................3
2. Warnings .........................................................................................................................................3
3. Getting Started ................................................................................................................................3
3.1 Parts List.................................................................................................................................3
3.2 Tools.......................................................................................................................................3
3.3 Quick Start Guide...................................................................................................................3
3.4 Product Features.....................................................................................................................5
3.4.1 Display...............................................................................................................................5
3.4.2 SensorArray.......................................................................................................................6
3.5 Powering Up...........................................................................................................................6
3.5.1 Power Up Sequence ...........................................................................................................6
3.5.2 Initial Sensor Synchronization...........................................................................................8
3.5.3 Site Survey.........................................................................................................................8
3.5.4 Pole Mounting the Sensor Array........................................................................................8
4. Console Display............................................................................................................................ 11
5. Settings..........................................................................................................................................12
5.1 Time Settings........................................................................................................................12
5.1.1 Time Zone Settings ..........................................................................................................14
5.2 Month Day vs. Year Display ................................................................................................15
5.3 Moon Phase..........................................................................................................................15
5.4 Sunrise and Sunset ...............................................................................................................16
5.5 Wi-Fi Connection Status ......................................................................................................16
5.6 Time Server Sync Status ......................................................................................................16
5.7 Alarm Settings......................................................................................................................17
5.7.1 Turning on and Off theAlarm Feature.............................................................................17
5.7.2 Setting the Alarm Time ....................................................................................................17
5.7.3 Using the Alarm and Snooze Functions...........................................................................17
5.8 Temperature and Humidity Display and Settings.................................................................18
5.8.1 Temperature Units of Measure.........................................................................................18
5.8.2 Outdoor SensorArray Signal Strength.............................................................................18
5.8.3 Optional 7-Channel Sensors.............................................................................................18
5.8.4 Temperature and Humidity Trend ....................................................................................19
5.8.5 Temperature and Humidity Measurements Limits...........................................................19
5.9 Wind.....................................................................................................................................19
5.9.1 Average Wind Speed, Wind Gust and Beaufort Scale......................................................20
5.9.2 Wind Units of Measure and Wind Direction Format .......................................................21
5.9.3 Wind Speed Level Indicator.............................................................................................22
5.10 Barometric Pressure Display and Settings ...........................................................................22
5.10.1 Barometric Pressure Units of Measure ........................................................................22
5.10.2 Absolute Pressure vs. Relative Pressure ......................................................................22
5.10.3 Relative Pressure Calibration.......................................................................................22
5.11 The Forecast.........................................................................................................................23
5.12 Weather Index.......................................................................................................................23

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 2
5.13 Feels Like.............................................................................................................................23
5.13.1 UV Index, Light Intensity and Sunburn Time..............................................................24
5.13.2 Wind Chill....................................................................................................................26
5.13.3 Heat Index....................................................................................................................26
5.13.4 Dew Point.....................................................................................................................27
5.14 Rainfall.................................................................................................................................27
5.14.1 Rain Units of Measure .................................................................................................28
5.14.2 Rain Increments of Measure........................................................................................28
5.14.3 Resetting Rain to Zero .................................................................................................28
5.15 Min / Max.............................................................................................................................28
5.16 History Data (Past 24 hours)................................................................................................29
5.17 Alerts....................................................................................................................................29
5.17.1 Setting the Alerts..........................................................................................................29
5.17.2 Activating anAlert.......................................................................................................30
5.17.3 Silencing anAlert.........................................................................................................31
5.17.4 Alert Duration..............................................................................................................31
5.18 Backlight..............................................................................................................................31
6. Connect your Console to Wi-Fi and the Internet...........................................................................31
6.1 Register at Third Party Public Websites (optional): .............................................................31
6.2 Place Console in Access Point Mode...................................................................................31
6.3 Connect to the Console’s Wi-Fi Server................................................................................32
6.4 Register withAmbientWeather.net.......................................................................................35
6.5 Additional AmbientWeather.net Features.............................................................................36
6.5.1 IFTTT...............................................................................................................................36
6.5.2 Compatible with Alexa.....................................................................................................37
6.5.3 Works with GoogleAssistant...........................................................................................37
6.6 Advanced Settings................................................................................................................37
6.6.1 Calibration........................................................................................................................38
6.6.2 NotesAbout Calibration...................................................................................................39
6.6.3 Calibrating the Wind Direction for the Southern Hemisphere.........................................40
6.6.4 Firmware Updates............................................................................................................40
7Maintenance..................................................................................................................................41
8Battery Replacement.....................................................................................................................41
9Adding or Subtracting Multiple Sensors.......................................................................................42
9.1 Adding or Subtracting Sensors.............................................................................................42
9.2 Optional Sensors ..................................................................................................................42
9.3 Assigning Optional Sensor Channels...................................................................................43
10 Specifications ...........................................................................................................................43
10.1 Wireless Specifications ........................................................................................................43
10.2 Measurement Specifications.................................................................................................44
10.3 Power Consumption.............................................................................................................44
10.4 Wi-Fi Specifications.............................................................................................................44
10.5 Other Specifications.............................................................................................................45
10.6 Weight Specifications...........................................................................................................45
11 Troubleshooting Guide.............................................................................................................45
12 Liability Disclaimer..................................................................................................................47
13 FCC Statement..........................................................................................................................47
14 Warranty Information...............................................................................................................48
15 California Prop 65 ....................................................................................................................48

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 3
1. Introduction
Thank you for your purchase of theAmbient Weather WS-7079 Wi-Fi Smart Weather Station.
The following user guide provides step by step instructions for installation, operation and
troubleshooting. To download the latest full-sized manual and additional troubleshooting tips, please
visit:
https://help.ambientweather.net/product/ws-7079
2. Warnings
Warning. Only use the included approved AC adapter.
Warning: Any metal object may attract a lightning strike, including your weather station
mounting pole. Never install the weather station in a storm.
Warning: Installing your weather station in a high location may result in injury or death.
Perform as much of the initial check out and operation on the ground and inside a building or
home. Only install the weather station on a clear, dry day.
3. Getting Started
Note: Remove the plastic film from the console face before getting started.
3.1 Parts List
QTY
Item
1
Display Console
Frame Dimensions (L x W x H): 9.4 x 5.5 x 0.8 in
1
Wireless Outdoor SensorArray (L x W x H): 13.5 x 15.5 x 5.4”
2
Rubber pads for pole mount.
1 set
Sensor array screw bolt, screws and screw nut
1 set
Sensor array mounting kit
1
UL Rated Class 6 AC Adapter
1
CR2032 Button Battery
1
User Manual
3.2 Tools
•Precision screwdriver
•Compass or GPS
3.3 Quick Start Guide
Although the manual is comprehensive, much of the information contained may be intuitive. In
addition, the manual does not flow properly because the sections are organized by components.
The following Quick Start Guide provides only the necessary steps to install, operate the weather
station, and upload to the internet, along with references to the pertinent sections.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 4
✓
Step
Description
Section
1
Assemble and power up the sensor array
3.5
2
Power up the display console and synchronize with sensor
array
3.5
3
Mount the sensor array
3.5.4
4
Set console settings
5
5
Calibrate the relative pressure to sea-level conditions
(local airport) on console
5.10.3
6
Reset the rain to zero on console (due to movement during
installation)
5.14.3
7
Register at Wunderground.com (optional)
6.4
8
Configure Wi-Fi, Server Settings, and Location
6.2
9
Register at AmbientWeather.net
6.3

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 5
3.4 Product Features
3.4.1 Display
1
ALARM/SNOOZE Button
2
CHANNEL button
3
HISTORY button
4
MAX / MIN button
5
WIND button
6
SUN button
7
BARO button
8
RAIN button
9
LCD display
10
CLOCK SET button
11
ALARM button
12
Wall hanging suspension
eye
13
ALERT button
14
NDX / Index button
15
/ button
16
SENSOR / WIFI button
17
REFRESH button
18
°C / °F button
19
RESET button
19
Battery compartment
20
Power jack
21
HI / LO / AUTO slide
switch
22
Battery door
23
Table stand
Figure 1

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 6
3.4.2 SensorArray
Figure 2
No
Description
No
Description
1
Antenna
9
Wind vane
2
Rain collector
10
Red LED indicator
3
UV / light sensor
11
[RESET] button
4
Mounting pole
12
Battery door
5
Mounting base
13
Mounting clamp
6
Balance indicator
14
Rain sensor
7
Wind cups
15
Tipping bucket
8
Radiation shield
16
Drain holes
3.5 Powering Up
3.5.1 Power Up Sequence
Note: The power up sequence must be performed in the order shown in this section sensor array
FIRST, display console SECOND) to avoid sensor synchronization time out.
The Outdoor SensorArray:
1. Unscrew the battery door at the bottom of the sensor array and insert 3 x AA batteries

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 7
according to the polarity information marked on the battery compartment.
Figure 3
2. Replace the battery door and screw on tightly.
3. The transmission status LED will begin flashing once per 12 seconds.
The Console:
Important Note: The power up sequence must be performed in this order (battery first, AC
adapter second) to prevent a low battery indication at power up.
Place the sensor array about 5 to 10 feet from the display console.
Figure 4
1. Reference Figure 4. Rotate the battery lid counter-clockwise to open the battery door.
2. Gently pull out the battery pull tab.
3. Rotate the battery lid clockwise to close the battery door.
4. Plug the AC adaptor into the DC jack of the console.
5. After power up, all of LCD segments will be displayed. The console will enter access point
(AP) mode, and the status LED will flash green.
6. Do not touch any buttons until sensor synchronization is complete.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 8
Note: If no display is present after powering up the console, press the [RESET] button on the
back of the console with an open-ended paper clip or sharp tool.
3.5.2 Initial Sensor Synchronization
The console will automatically search for and connect to the optional sensors and outdoor sensor array
after it is powered up. You can also press [Wi-Fi / SENSOR] button to force the console to search for
the sensors.
Once the sensor array connection is successful, the antenna mark and readings for outdoor temperature,
humidity, wind speed, wind direction, rainfall and UV will appear on the display.
3.5.3 Site Survey
Perform a site survey before installing the sensor array. Consider the following:
1. You must clean the rain gauge every few months and change the batteries every 2-3 years.
Provide easy access to the weather station.
2. Avoid radiant heat transfer from buildings and structures. In general, install the sensor array at
least 5’ from any building, structure, ground, or roof top.
3. Avoid wind and rain obstructions. The rule of thumb is to install the sensor array at least four
times the distance of the height of the tallest obstruction. For example, if the building is 20’
tall, and the mounting pole is 6’ tall, install 4 x (20 – 6)’ = 56’ away.
4. Wireless Range. The radio communication between receiver and transmitter in an open field
can reach a distance of up to 300 feet, providing there are no interfering obstacles such as
buildings, trees, vehicles, high voltage lines. Wireless signals will not penetrate metal
buildings. Under most conditions, the maximum wireless range is 100’.
5. Radio interference such as PCs, radios or TV sets can, in the worst case, entirely cut off radio
communication. Please take this into consideration when choosing console or mounting
locations. Make sure your display console is at least five feet away from any electronic device
to avoid interference.
6. Visit Ambient Weather Mounting Solutions for assistance and ideas for mounting your
weather station:
http://www.ambientweather.com/amwemoso.html
3.5.4 Pole Mounting the SensorArray
The sensor array includes an easy mounting bracket for mounting to any pole between 1” and 2”. If
your pole diameter is greater than 2”, consider a mast-to-mast mounting bracket and standard 1 3/8”
pole available from Ambient Weather.
Mount the sensor array mounting bracket to your pole (not included) using a Philips screwdriver.
Tighten the bolts to the nuts seated inside the hexagonal bolt wells. Add the included rubber gripping
pads to the bracket.
Before completely tightening, point the wind vane to the North as shown in Figure 5, Step 5.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 9
Step
Image
Step 1:
Insert the top side of the pole to the square hole
of the weather sensor.
Note: Ensure the pole and sensor's
indicator align.
Step 2:
Place the nut in the hexagon hole on the sensor
array, then insert the screw in other side and
tighten it with a precision screwdriver.
Step 3:
Insert the other side of the pole to the square
hole of the plastic stand.
Note: Ensure the pole and stand's indicator
align.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 10
Step 4:
Place the nut in the hexagon hole of the stand,
then
insert the screw in the other side, and then
tighten with a precision screwdriver.
Step 5:
Install the sensor array in an open area with no
obstructions above or around the sensor array
for accurate rain and wind measurement.
Install the sensor array with the anemometer
(wind sensors) facing North to properly orient
the wind direction vane.
Secure the mounting stand and clamps
(included) to a post or pole, and allow
minimum 5 feet off the ground.
Figure 5
The mounting pole can be attached to a railing or another pole, as shown in Figure 6.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 11
Figure 6
4. Console Display

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 12
No
Description
No
Description
1
Outdoor temperature & humidity.
6
Sun (UV, Light Intensity, Sunburn Time)
2
Wind direction & speed
7
Rain
3
Forecast and barometer
8
Calendar and Moon Phase
4
Indoor temperature & humidity. The sensors
are located inside the display console.
9
Time and Alarm
5
Feels Like Temperature Heat Index & Wind
Chill)
10
Sunrise and Sunset
Figure 7
5. Settings
5.1 Time Settings
While in normal time mode, perform the following operations to set the time. Note that once
connected to the Internet, and you set the correct time zone (TZ) and daylight savings time (DST), the
time will set automatically.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 13
Command
Mode
Settings
Image
[CLOCK
SET] + 2
seconds
Enter Time Zone
Settings
Press [ ] to increase, [ ] to
decrease. Reference Figure
9.
[CLOCKSET]
Enter Daylight
Savings Time
OFF (AZ and HI)
or auto
(everywhere
else).
Press [ ] or [ ] to turn ON
or OFF.
[CLOCKSET]
Hour
Press [ ] to increase, [ ] to
decrease.
[CLOCKSET]
Minute
Press [ ] to increase, [ ] to
decrease.
[CLOCKSET]
Second
Press [ ] to reset to 0.
[CLOCKSET]
Hour Format
Press [ ] to toggle between
12 Hr and 24 Hr format.
[CLOCKSET]
Year
Press [ ] to increase, [ ] to
decrease.
[CLOCKSET]
Month
Press [ ] to increase, [ ] to
decrease.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 14
[CLOCKSET]
Day
Press [ ] to increase, [ ] to
decrease.
[CLOCKSET]
Month Day
Format
Press [ ] or [ ] to toggle
between M-D (month-day)
and D-M (day-month)
[CLOCKSET]
Enable or disable
the internet time
sync
Press [ ] or [ ] to turn ON
or OFF
[CLOCKSET]
Language
Press [ ] or [ ] to change
between EN (English), DE
(German), FR (French), ES
(Spanish) IT (Italian), NL
(Dutch), and RU (Russian)
[CLOCKSET]
Exit Time
Settings
[CLOCKSET] + 2 seconds means press and hold the CLOCKSET button on the back of the display
console for two seconds.
[CLOCKSET] means press but do not hold the CLOCKSET button.
Figure 8
5.1.1 Time Zone Settings
The following table provides times zones throughout the world. Locations in the eastern hemisphere
are positive, and locations in the western hemisphere are negative.
Hours from
GMT
Time Zone
Cities
-12
IDLW: International Date Line West
---
-11
NT: Nome
Nome,AK
-10
AHST: Alaska-Hawaii Standard
CAT: Central Alaska
HST: Hawaii Standard
Honolulu, HI
-9
YST: Yukon Standard
Yukon Territory

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 15
Hours from
GMT
Time Zone
Cities
-8
PST: Pacific Standard
Los Angeles, CA, USA
-7
MST: Mountain Standard
Denver, CO, USA
-6
CST: Central Standard
Chicago, IL, USA
-5
EST: Eastern Standard
New York, NY, USA
-4
AST: Atlantic Standard
Caracas
-3
---
São Paulo, Brazil
-2
AT: Azores
Azores, Cape Verde Islands
-1
WAT: West Africa
---
0
GMT: Greenwich Mean
WET: Western European
London, England
1
CET: Central European
Paris, France
2
EET: Eastern European
Athens, Greece
3
BT: Baghdad
Moscow, Russia
4
---
Abu Dhabi, UAE
5
---
Tashkent
6
---
Astana
7
---
Bangkok
8
CCT: China Coast
Bejing
9
JST: Japan Standard
Tokyo
10
GST: Guam Standard
Sydney
11
---
Magadan
12
IDLE: International Date Line East
NZST: New Zealand Standard
Wellington, New Zealand
Figure 9
5.2 Month Day vs. Year Display
To change the date field from Month / Day to Year, press (do not hold) the CLOCK button.
5.3 Moon Phase
The phase of the moon is determined by the time, date and time zone. Figure 10 displays the moon
phases for the Northern and Southern Hemisphere.
Reference the web setup interface (Figure 42) for selecting Northern or Southern Hemisphere.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 16
Figure 10
5.4 Sunrise and Sunset
The console calculates your location’s sunrise and sunset time based on your time zone, latitude and
longitude you entered.
Figure 11
5.5 Wi-Fi Connection Status
When the console successfully connects to your Wi-Fi router, the Wi-Fi signal icon will appear
in the time field on the LCD display. If the Wi-Fi signal is not stable or the console is trying to connect
to the router, the icon will flash. If the icon disappears, it means the console is not connected to the
Wi-Fi router.
5.6 Time Server Sync Status
After the console has connected to the internet, it will attempt to connect to the internet time server to
obtain the UTC time. Once the connection succeeds and the console's time has been updated, the
icon will appear in the Time field of the display. If the console cannot sync the time server,
you can press the REFRESH button to force the time synchronization process, and the SYNC icon
will flash.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 17
Figure 12
5.7 Alarm Settings
5.7.1 Turning on and Off theAlarm Feature
In normal mode, press the ALARM button to show the alarm time. Press the alarm button again, and
the alarm icon will appear. Press the alarm button again, and the pre-alert icon will
appear. Press the alarm button again, and the alarm and pre-alert to turn off, and no alarm will sound.
Figure 13
5.7.1.1 Pre-Alert Feature
The pre-alert wakes you 30 minutes earlier if ice is predicted to allow you extra time to get to work or
school.
Once the ice pre-alert is activated, the alarm will sound 30 minutes earlier if the outdoor temperature
is below -3°C (26.6 °F), where ice is likely to form.
5.7.2 Setting theAlarm Time
While in normal mode, perform the following operations to set the alarm time.
Command
Mode
Settings
[ALARM] + 2
seconds
Enter Alarm Settings
Alarm Hour
Press [UP] to increase, [DOWN] to decrease.
[ALARM]
Alarm Minute
Press [UP] to increase, [DOWN] to decrease.
[ALARM]
Exit Alarm Settings
[ALARM] + 2 seconds means press and hold theALARM button on the back of the display for two
seconds.
[ALARM] means press but do not hold the ALARM button on the back of the display.
Figure 14
5.7.3 Using theAlarm and Snooze Functions
When the alarm sounds, press and hold the ALARM / SNOOZE button for two seconds to turn off
the alarm sound. The alarm bell will stop flashing.
If no button is pressed during the alarm period, the alarm will turn off automatically after two minutes.
To temporarily silence the alarm, press the ALARM / SNOOZE button on the top of the console. The
alarm bell icon will keep flashing.
If the snooze function is turned on, the 4-step crescendo alarm will sound every 2 minutes. Press and

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 18
hold the ALARM / SNOOZE button for two seconds to turn off the alarm sound. The alarm bell will
stop flashing.
5.8 Temperature and Humidity Display and Settings
5.8.1 Temperature Units of Measure
Press the °F / °C button on the front of the display to change the temperature units of measure.
5.8.2 Outdoor SensorArray Signal Strength
The outdoor sensor array signal strength is displayed in the outdoor section of the display:
Figure 15
5.8.3 Optional 7-Channel Sensors
5.8.3.1 Channel Sensor Signal Strength
The channel sensor signal strength is displayed in the indoor section of the display, next to the channel
number:

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 19
Figure 16
5.8.3.2 Changing Channel Numbers
The console supports up to seven optional wireless indoor and outdoor sensors. If you have two or
more sensors, press the CHANNEL button to switch to different channels.
Press and hold the CHANNEL button for two seconds to automatically scroll between the channels
every four seconds. To stop the automatic scrolling, press the CHANNEL button again.
5.8.3.3 Indoor Comfort Icon
The comfort indication is a pictorial indication calculated from the indoor air temperature and
humidity. Each channel displays a comfort icon.
The comfort indication can vary at the same temperature, depending on the humidity. There is no
comfort Indication when the temperature is below 0°C (32°F) or over 60°C (140°F).
Figure 17
5.8.4 Temperature and Humidity Trend
The temperature trend arrow indicator displays the current rate of change of the indoor and outdoor
temperature and humidity.
Figure 18
5.8.5 Temperature and Humidity Measurements Limits
When temperature is below -40 °C, (-40 °F), the LCD will display “Lo”. If temperature is above 80 °C
(176 °F), LCD will display “HI”.
When humidity is below 1%, the LCD will display “Lo”. If humidity is above 99%, the LCD will
display “HI”.
5.9 Wind
The wind section displays wind speed (gust or average), current wind direction, predominant wind
direction (over the last 5 minutes), and wind speed level.

Version 1.0 ©Copyright 2020, Ambient LLC. All Rights Reserved. Page 20
Figure 19
5.9.1 Average Wind Speed, Wind Gust and Beaufort Scale
To change the display between average wind speed, wind gust and Beaufort scale, press the WIND
button on the front of the display.
The wind speed is the average calculated by the sensor array in the 12 second update period. The wind
gust is the maximum calculated by the sensor array in the 12 second update period, and then passed to
the console. Thus, you never miss a wind gust.
The Beaufort Scale is an international scale of wind velocities ranging from 0 (calm) to 12 (Hurricane
force).
The Beaufort Scale is defined as follows:
Beaufort Scale
Description
Wind Speed
Land Condition
0
Calm
< 1 km/h
Calm. Smoke rises
vertically.
< 1 mph
< 1 knot
< 0.3 m/s
1
Light air
1.1 - 5.5 km/h
Smoke drift indicates
wind direction.
Leaves and wind vanes
are stationary.
1 - 3 mph
1 - 3 knot
0.3 - 1.5 m/s
2
Light breeze
5.6 - 11 km/h
Wind felt on exposed
skin. Leaves rustle.
Wind vanes begin to
move.
4 - 7 mph
4 - 6 knot
1.6 - 3.3 m/s
3
Gentle breeze
12 - 19 km/h
Leaves and small twigs
constantly moving,
light flags extended.
8 - 12 mph
7 - 10 knot
3.4 - 5.4 m/s
4
Moderate breeze
20 - 28 km/h
Dust and loose paper
raised. Small branches
begin to move.
13 - 17 mph
11 - 16 knot
5.5 - 7.9 m/s
5
Fresh breeze
29 - 38 km/h
Branches of a moderate