AMC SMILE 19 User manual

www.amcelettronica.com Instrucciones de instalación v1.1
SMILE 19 Sensor Pir
1
SMILE 19 - SMILE 19/P


SMILE 19 is a Digital PIR sensor, with an analysis system that takes into account the two most important
changes that may occur during a movement: the speed and the intensity. With the simultaneous comparison
of these two information, the sensor is able to discriminate repetitive movements from intrusion, lowering
the percentage of false alarms. With hight thermal variations, the totally digital temperature compensation
system, guarantees a great performance. Has 51mt coverage, with angle of 90 °. With the special lens is
equipped of creep zone. Is available also in pet immune up to 15 kg version (Smile19/P).To disassemble the
detector just press the tooth on the bottom of the case (see figure) and pull out the PCB by pushing the clip
and by levering on the ABS supports (see figure). In this way it will be possible to freely work on the PCB.

- By using a thin screwdriver, push the round tooth on the bottom and open the housing (see figure 1)
- Remove the PCB from the base by levering on the ABS supports (see figure 2)
- Pierce the knock on the base of cover on the desired point for fixing,or use the optional swivel bracket.
- recommended height 2mt
- slide the cable into the back seat, and out of the top hole
- Wire up the terminals following the connections shown in figure.

To disable the walk test LED open the JP2 LED
To enable doubble pulse close the JP1
AP: Tamper terminal
ALARM Alarm terminal
SUPPLY: power supply 13.8Vcc
SMILE 19 es un sensor infrarrojos digital, con un sistema de análisis que tiene en cuenta las dos variacio-
nes más importantes que pueden ocasionarse durante un movimiento: la velocidad y la intensidad.
Con la comparación simultánea de estas 2 informaciones, el sensor es capaz de distinguir entre movimien-
tos repetitivos y las intrusiones efectivas, reduciendo considerablemente el porcentaje de falsas alarmas. El
sistema de compensación térmica completamente digital garantiza siempre la máxima eficacia incluso en
presencia de considerables variaciones térmicas. Tiene un alcance de unos 15 m con ángulo de apertura
de 90° y la lente especial nido de abeja permite también el control antiarrastre. También está disponible
en la configuración inmune a las mascotas de hasta 15 kg (smile19/). Para acceder a la tarjeta electrónica,
sólo hay que pulsar la tecla en el fondo de la cubierta (vea la imagen) y, haciendo palanca sobre los bloques
en ABS, será posible extraer la tarjeta electrónica y trabajar con total libertad.


Utilice un pequeño destornillador, empuje el botón redondo que se encuentra en la parte delantera del
sensor y abra la cubierta.
- retire la tarjeta electrónica del fondo de la cubierta haciendo palanca sobre el enganche del lado de los bornes.
- perfore los agujeros ciegos de montaje que se van a utilizar para la fijación, o bien utilice la articulación
correspondiente (opcional). - La altura recomendada para la fijación es 2 m.
- haga deslizar el cable por la guía correspondiente que se encuentra en la parte trasera de la cubierta, ha-
ciendo que salga por el agujero que está en la parte superior.
- efectúe el cableado del circuito siguiendo la guía para las conexiones (figura 3).

Para desactivar totalmente el led  se puede abrir el JP2 
Para habilitar el doble impulso, cierre el JP1.
AP: terminal tamper
ALARM: terminal alarma
SUPPLY: alimentación 13.8Vcc
 
Premere qui per aprire
Press here to open
Led WALK TEST
Lente / Lens
Sfondabili per fissaggio
Mounting knockouts
Fissaggio circuito
Clip for electronic board
Pulse aquí para abrir
Agujeros ciegos de montaje
Fijación circuito

www.amcelettronica.com Instrucciones de instalación v1.1
SMILE 19 Sensor Pir
2

SMILE 19 posibilita una
cobertura de 15 m, la
conformación especial
de la lente posibilita una
apertura horizontal de
más de 90° con 29 haces
en 5 niveles
SMILE 19 allows a ran-
ge of 15 mt, the special
lens shape provides a
horizontal coverage of
more than 90° with 29
patterns on 5 levels.
SMILE 19
Input Voltage / Alimentación 9 to 15 Vcc
Current Drain / Consumo (18 mA/9.5mA) @ 13.8 Vcc
Coverage / Alcance en longitud 15 mt
Angle / Alcance en ancho 90°
Piroeléctrico / PIR 2 elements/ 2 elements
Lens / Lente 29 haces en/patterns on 5 levels/niveles
Anti-opening / Autoprotection ✔
Creep zone / Antiarrastre ✔
Alarm contact / Contacto de alarma 0.2 A - 24 Vcc
Tamper switch / Contacto de tamper Max/ Máx 40 mA - 30 Vcc
Operating temperature / Temperatura de ejercicio From / Desde -10 °C to/ hasta +55 °C
Protection / RFI Protección 30 V / m (20 MHz - 2000 MHz)
Led WALK TEST / Led PRUEBA DE MOVIMIENTO ✔
WALK TEST IN / PRUEBA DE MOVIMIENTO IN ✔
Housing / Cubierta ABS
Dimensions / Dimensiones 110 x 60 x 46 mm

Installation must be carried out following the local installation norms by qualified personnel.
The manufacturer refuses any responsibility when changes or unauthorized repairs are made to the product/system.
It is recommended to test the operation of the alarm product/system at least once a month. Despite frequent testing and due to, but not limited to,
any or all of the following: tampering, electrical or communication disruption or improper use, it is possible for the product/system to fail to prevent
burglary, rubbery, fire or otherwise. A properly installed and maintained alarm system can only reduce the risk that this happens.
La instalación debe ser realizada correctamente por personal especializado.
El fabricante declina cualquier responsabilidad en caso de que el producto sea manipulado por personas no autorizadas.
Se recomienda verificar el correcto funcionamiento del sistema de alarmas al menos una vez al mes, a pesar de ello, tenga en cuenta que un sistema de
alarmas electrónico fiable no evita las intrusiones, atracos, incendios y demás, sino que se limita a disminuir el riesgo de que dichas situaciones se ocasionen.


JP1= doubble pulse
JP2 = Walk test led
ALARM = alarm contact
AP = tamper contact
SUPPLY = power supply 13.8Vcc
JP1= doble impulso
JP2 = led de prueba de movimiento
ALARM = contacto alarma
AP = contacto tamper
SUPPLY = alimentación 13.8Vcc
VISTA IN PIANTA
VISTA LATERALE
Copertura minima
Copertura massima
0°
45°
45°
VISTA IN PIANTA
VISTA LATERALE
Copertura minima
Copertura massima
0°
45°
45°
PET IMMUNE
NORMAL

www.amcelettronica.com Installation Instructions v1.1
SMILE 19 Pir Detector
1
SMILE 19 - SMILE 19/P


SMILE 19 is a Digital PIR sensor, with an analysis system that takes into account the two most important
changes that may occur during a movement: the speed and the intensity. With the simultaneous comparison
of these two information, the sensor is able to discriminate repetitive movements from intrusion, lowering
the percentage of false alarms. With hight thermal variations, the totally digital temperature compensation
system, guarantees a great performance. Has 15mt coverage, with angle of 90 °. With the special lens is
equipped of creep zone. Is available also in pet immune up to 15 kg version (Smile19/P).To disassemble the
detector just press the tooth on the bottom of the case (see figure) and pull out the PCB by pushing the clip
and by levering on the ABS supports (see figure). In this way it will be possible to freely work on the PCB.

- By using a thin screwdriver, push the round tooth on the bottom and open the housing (see figure 1)
- Remove the PCB from the base by levering on the ABS supports (see figure 2)
- Pierce the knock on the base of cover on the desired point for fixing,or use the optional swivel bracket.
- recommended height 2mt
- slide the cable into the back seat, and out of the top hole
- Wire up the terminals following the connections shown in figure.

To disable the walk test LED open the JP2 LED
To enable doubble pulse close the JP1
AP: Tamper terminal
ALARM Alarm terminal
SUPPLY: power supply 13.8Vcc
SMILE 19 è un sensore infrarosso digitale, con un sistema di analisi che tiene in considerazione le 2 piu
importanti variazioni che possono avvenire durante un movimento: la velocità e la l’intensità.
Con la comparazione simultanea di queste 2 informazioni il sensore è in grado di discriminare movimenti
ripetitivi da intrusioni vere e proprie, abbassando la percentuale di falsi allarmi in modo considerevole.
Anche in presenza di variazioni termiche notevoli il sistema di compensazione termica totalmente digitale
garantisce sempre un ottima efficacia. Ha una portata di circa 15mt, con un angolo di apertura di 90° e la
speciale lente a nido d’ape permette anche il controllo antistrisciamento. E’ diponibile anche nella versione
pet immune fino a 15kg (smile19/P). Per accedere alla scheda elettronica sarà sufficiente fare pressione su
un tasto sul fondo della cover (vedi figura) e, facendo leva sui blocchetti in ABS, si potrà estrarre la scheda
elettronica e lavorare in piena libertà.


Utilizzando un mini cacciavite, spingere il tastino tondo sul lato anteriore del sensore e aprire la cover.
- rimuovere la scheda elettronica dal fondo della cover facendo leva sulla clips lato morsetti
- forare gli sfondabili che si desidera utilizzare per il fissaggio, oppure utilizzare l’apposito snodo (opzionale).
- Altezza consigliata per il fissaggio 2m.
- fare scorrere il cavo attraverso l’apposita guida sul retro della cover facendolo uscire dal foro in alto.
- cablare il circuito seguendo la guida ai collegamenti (figura 3).

Per disabilitare completamente il led  si può aprire il JP2 
Per abilitare il doppio impulso chiudere il JP1.
AP: terminale tamper
ALARM: terminale allarme
SUPPLY: alimentazione 13.8Vcc
 
Sfondabili per fissaggio
Mounting knockouts
Fissaggio circuito
Clip for electronic board
Premere qui per aprire
Press here to open
Led WALK TEST
Lente / Lens

www.amcelettronica.com Installation Instructions v1.1
SMILE 19 Pir Detector
2

SMILE 19 permette una
copertura di 15 mt, la
speciale conformazio-
ne della lente permette
un’apertura orizzontale
di oltre 90° con 29 fasci
su 5 livelli
SMILE 19 allows a ran-
ge of 15 mt, the special
lens shape provides a
horizontal coverage of
more than 90° with 29
patterns on 5 levels.
SMILE 19
Alimentazione / Input Voltage 9 to 15 Vcc
Consumo / Current Drain (18 mA/9.5mA) @ 13.8 Vcc
Portata in lunghezza / Coverage 15 mt
Portata in larghezza / Angle 90°
Piroelettrico / PIR 2 elementi / 2 elements
Lente / Lens 29 patterns on 3/5 levels
Antiapertura / Anti-opening ✔
Antistrisciamento / Creep zone / ✔
Contatto di allarme / Alarm contact 0.2 A - 24 Vcc
Contatto di tamper / Tamper switch Max 40 mA - 30 Vcc
Temperatura di esercizio / Operating temperature From -20 °C to +55 °C
RFI Protezione / Protection 30 V / m (20 MHz - 2000 MHz)
Led WALK TEST ✔
WALK TEST IN ✔
Cover / Housing / Boiter ABS
Dimensioni / Dimensions 110 x 60 x 46 mm

L’installazione deve essere eseguita a regola d’arte da personale specializzato.
Il produttore declina ogni responsabilità nel caso in cui il prodotto venga manomesso da persone non autorizzate.
Si raccomanda di verificare il corretto funzionamento del sistema d’allarme almeno una volta al mese, tuttavia un sistema di allarme elettronico
affidabile non evita intrusioni, rapine, incendi o altro, ma si limita a diminuire il rischio che tali situazioni si verifichino.
Installation must be carried out following the local installation norms by qualified personnel.
The manufacturer refuses any responsibility when changes or unauthorized repairs are made to the product/system.
It is recommended to test the operation of the alarm product/system at least once a month. Despite frequent testing and due to, but not limited to,
any or all of the following: tampering, electrical or communication disruption or improper use, it is possible for the product/system to fail to prevent
burglary, rubbery, fire or otherwise. A properly installed and maintained alarm system can only reduce the risk that this happens.

JP1= doubble pulse
JP2 = Walk test led
ALARM = alarm contact
AP = tamper contact
SUPPLY = power supply 13.8Vcc
JP1= doppio impulso
JP2 = Walk test led
ALARM = contatto allarme
AP = contatto tamper
SUPPLY = alimetazione 13.8Vcc
VISTA IN PIANTA
VISTA LATERALE
Copertura minima
Copertura massima
0°
45°
45°
VISTA IN PIANTA
VISTA LATERALE
Copertura minima
Copertura massima
0°
45°
45°
PET IMMUNE
NORMAL