AMC PROMASK User manual

www.amcelettronica.com Installation Instructions
Promask Dual Technology ver. 1.2
PROMASK is a Microprocessed Digital Dual Technology Detector. It combines a Dual Element PIR with temperature
compensation, and a X Band Microwave Section with Broadcast Pulse Planar Cavity. Thanks to its special algorithm
it’s able to reach a coverage of 20mt and an angle of more than 90°, ensuring an outstanding immunity to false alarms.
In addiction it’s possibile to set the detector’s sensitivity from 3 to 20 mt. It can work in different configurations, AND:
alarm is triggered only when detection comes both technologies (maximum false alarm immunity),OR: as soon as one
technology detects, the alarm is triggered, OR 2 pulse: the alarm is triggered when a tecnology detects two times.
Auto OR: AND-Type Working Mode with check of consecutive alarms from each technology with relative alarm Notifi-
cation when one of them is switched off .PROMASK is provided with an antimasking control on both tecnology; mask
terminal provided to this. Accellerometer provide to segnalling tamper alarms. (wrench, shoks). The noise function is
special electronic filter to prevent false alarm. Please note that this feature is not certified
1. INTRODUCTION
ENGLISH
2. INSTALLATION
By using a thin screwdriver, push the squared tooth on the bottom and open the housing, remove the PCB from the base by un-
screwing the central screw, use a screwdriver to pierce the knockouts on the side of the base where you wish to attach the detector
to the wall.
- Route the wires and let them pass through the hole on the top of the housing.
- Wire up the terminals following the connections shown in figure
- Fix the PCB to the Housing’s Bottom using the central screw
.Verify that all DIP Switches are in the desired position (see the following scheme)
Remark: The suggested height from the floor is 2 m (5 ft.).
.FIRST SETUP: the detector needs an autotest, that must be done with the cover closed. Then closed the detector , power up it,
and wait that the led finish to flash (about 40 sec.). Now the detector can work.
If necessary turn the trimmer to adjust the MW range, so as to let the MW detect the movements at the distance you need.
“+” ⇨ Higher range “-” ⇨ Shortest range
3. CONNECTIONS AND SETTINGS
DIP-SWITCH
TERMINALS
+/- 13.8 V DC Power Supply
B/S for stopping MW emition at control unit disarmed
ALARM Alarm Contact (N.C.)
TAMPER Tamper Contact (N.C.)
TRIMMER
TRIMMER Range Adjustment 3-20mt
PROMASK INSTALLATION
INSTALLAZIONE
Dual Technology Detector - Sensore a Doppia Tecnologia con antimascheramento
COMPLIANT
EN50131-2-4:2008
DIP3 on = antimasking enable, off = antimasking disable
DIP4 on = noise function enable, off = noise function disable
DIP5 off = MW always enable
DIP5 = on (B/s +12V) MW emition disable
DIP5 = on (B/s 0V) MW emition enable
DIP 6 on = led walk test enable, off = led walk test disable
dip 1 dip2 ALARM MODE
OFF OFF AND
ON OFF OR 1 PULSE
OFF ON AUTO OR
ON ON OR 2 PULSE

www.amcelettronica.com Installation Instructions
Promask Dual Technology ver. 1.2
5. GENERAL VIEW / VISTA GENERALE 6. TERMINALS / MORSETTIERA
7. LENS PERFORMANCES / PRESTAZIONI DELLA LENTE
Push Here to Open
Premere per Aprire
ATTENTION:
Must put the screw.
ATTENZIONE:
Obbligatorio mettere la vite.
Note: because this sensor is equipped with an accelerometer, was taken off the mechanical tamper system. Therefore, the
signalling of the sensor removal does not require any plug-tear
Nota: poichè questo sensore è provvisto di un accellerometro, è stato tolto il sistema tamper antistrappo meccanico, a
beneficio di quello elettronico. Pertanto la segnalazione di rimozione sensore non necessita di alcun tassello antistrappo,
si ricorda inoltre che tale funzione non è certificata .
Important: to the efficient operation doesn’t obscure in any way the field of view sensor
Importante: ai fini del buon funzionamento non oscurare in nessun modo il campo di visione del sensore

www.amcelettronica.com Installation Instructions
Promask Dual Technology ver. 1.2
AMC PRO MASK
Input Voltage / Alimentazione 9 to 15 V
Current Drain / Consumo (Alarm / Stand-By) 32 mA / 29 mA @ 13.8V
Tipical Voltage / Tensione nominale 13.8V
Coverage / Portata Massima 20mt
Aperture Angle / Angolo di Apertura 90°
PIR / Piroelettrico 2 Elements / 2 Elementi
Lens / Lente Fresnel (22 Patterns on 3 levels)
Microwave frequency / Frequenza Microonda 9.3 GHz / 9.9 GHz / 10,525 GHz
Alarm period / Durata allarme 2 sec.
Alarm Type / Tipo allarme AND - OR - AUTO OR
Anti-opening / Antiapertura ✔
Back Tamper / Antistrappo** ✔
Anti masking/ antimascheramento** ✔
Alarm Contact / Contatto di allarme 100 mA - 40 V - 2.5 -16 Ω
Tamper Switch / Contatto di Tamper Max 40 mA - 30 Vdc
Operating Temperature / Temperatura di esercizio From -10 °C to +55 °C
Storage Temperature / Temperatura di stoccaggio From -20 °C to +60 °C
RFI Protection / Protezione RFI 30 V / m (80 /1000 MHz)*
Walk Test LED (MW and PIR) ✔
Housing / Cover ABS
Dimensions / Dimensioni 130 x 66 x 38.5 mm
TECHNICAL FEATURES / SPECIFICHE TECNICHE
Prodotto conforme alla Direttiva 99/5/CE. La dichiarazione di conformità è disponibile presso la nostra sede.
Tutti i ns. prodotti sono conformi ai requisiti richiesti dalla norma CEI 79-2 2°ed. 1998 + Ab 2000.
L’installazione deve essere eseguita a regola d’arte da personale specializzato.
Il produttore declina ogni responsabilità nel caso in cui il prodotto venga manomesso da persone non autorizzate.
Si raccomanda di verificare il corretto funzionamento del sistema d’allarme almeno una volta al mese, tuttavia un sistema
di allarme elettronico affidabile non evita intrusioni, rapine, incendi o altro, ma si limita a diminuire il rischio che tali situa-
zioni si verifichino.
This product comply the 99/5/CE directive. The declaration of conformity is available at our offices.
Our products/systems comply with the essential requirements of EEC directives.
Installation must be carried out following the local installation norms by qualified personnel.
The manufacturer refuses any responsibility when changes or unauthorized repairs are made to the product/system.
It is recommended to test the operation of the alarm product/system at least once a month. Despite frequent testing and
due to, but not limited to, any or all of the following: tampering, electrical or communication disruption or improper use, it
is possible for the product/system to fail to prevent burglary, rubbery, fire or otherwise. A properly installed and maintained
alarm system can only reduce the risk that this happens.
* Certificazione : 10 V/m (80/1000 MHz) ** Non certificato
Meets the requirements:
Conforme ai requisiti:
R&TTE 99/5/CE
EN 50131-2-4: 2008
EN 50131-2-4 Grade 2
EN 50131-2-4 Class 2
CEI 79-2: I° Level