Amcrest SmartHome AD410 Instruction Manual
3
NOTE A corner bracket can be used to angle the doorbell
15° and the wedge bracket can be used to angle the
doorbell upward or downward at a 5° angle.
Wi-Fi Doorbell
3 Wire Nuts 2 Wall Anchors
2 Extra Wires
2 Mounting
Screws
2 Terminal
Screws
6mm (15/64”) Masonry Drill Bit
Wedge Bracket
(5º)
Corner Bracket
(15º)
Mounting Bracket
(Pre-installed)
Chime Kit
Pin Wire Harness
In the Box
Installing Your
Wi-Fi Doorbell
Model: AD410
SmartHome
2
B
Place a corner or wedge
bracket on the mounting
surface and mark the drill
holes with a marker or pencil.
A
Remove your existing
doorbell from the wall and
disconnect the wires. These
are the wires we will be using
to install your new Amcrest
Wi-Fi Doorbell.
Step 2: Installing Corner or Wedge Bracket
D
For Wood, Drywall or Soft Surfaces:
Secure the brackets to the mounting
surface using a screwdriver and mounting
screws.
For Concrete, Stucco or Brick: Using your
previously marked holes as a guide, drill
holes into the mounting surface using the
included masonry drill bit. Then, insert wall
anchors and secure the brackets using a
screwdriver and mounting screws.
CAttach a mounting bracket to the
corner or wedge bracket and press in to
snap the brackets together.
Step 2: Cont.
432
We’d Love to Hear From You!
We wanted to personally reach out and thank you for purchasing from our
Amazon store. Selling on Amazon is what we do to support our family, and
product reviews are the lifeblood of our business. It would mean the world to
us if you could take one minute of your time to help share the love by leaving
us an honest review using the link below:
www.amazon.com/ryp
Thank you again for being one of our amazing customers!
Sincerely,
Amcrest Team
Online Video Tutorial &
Quick Start Guide
amcrest.com/support
Need help?
How can we help?
We are dedicated to
providing the highest
quality support to our
customers and are
available 7 days a week.
Feed the wiring back into the wall. Then,
place the doorbell onto the mounting
bracket and slide it down to secure it.
Step 4: Mounting the Doorbell
NOTE
You will hear a click sound
once the doorbell has been secured
to the bracket.
Inserting a MicroSD Card (Optional)
On the back of the device locate the MicroSD
card slot. Raise the MicroSD card flap and insert
the MicroSD card, gold pins down. Secure the
flap back to the doorbell.
Supports 128GB MicroSD Card
(Class 10 or Higher)
128
GB
Step 5: Turn the Breaker Back On
The physical installation is now complete. Turn your breaker back
on and the allow the doorbell to power up. It may take the
doorbell up to 2 minutes to fully power up.
Now it’s time to setup the
Amcrest Smart Home App.
To connect your Amcrest Wi-Fi doorbell to
your Android or iOS mobile device, download
the Amcrest Smart Home app and follow the
instructions in the app setup.
Amcrest
Smart Home
8
Loosen the terminal screws
located on the back of your
Wi-Fi Doorbell using a screw-
driver. Place your existing
doorbell wiring underneath the
terminal screws, then re-tighten
the terminal screws to secure
the wires.
NOTE To attach the wires,
align the ends of the two
wires, place the wire nut
over the exposed wiring
and twist the wire nut
clockwise to tighten.
NOTE If your existing doorbell
wiring is too short, use the included
extra wires and wire nuts to extend
your wiring. Remove the terminal
screws completely then thread the
screws through the extra wire.
Step 3:
Connect Doorbell to Existing Wiring
85 76
Other manuals for SmartHome AD410
1
Other Amcrest Accessories manuals
