AMEC Camino-108 User manual

3
COPYRIGHT
The entire contents of this instruction manual, including any future updates, revisions,
and modifications, shall remain the property of AMEC at all times. Unauthorized
copies or reproduction of this manual, either in part or whole, in any form of print
and electronic media, is prohibited. The contents herein can only be used for the
intended purpose of this manual.
DISCLAIMER
AMEC is devoted to publish and maintain this product manual. As we continue to
improve our AIS products to satisfy all customers’ needs, information in this
document is subject to change without notice. AMEC does not make any
representations or warranties (implied or otherwise) regarding the accuracy and
completeness of this document and shall in no event be liable for any loss of profit or
any commercial damage, including but not limited to special, incidental,
consequential, or other damage.
Manual Revision: Version 1.28
User’s Manual

4
WARNING!
WARNING: The transponder must be installed and configured in conformity
with the provided instructions in the manual in order to maximize the device
performance.
WARNING: Please bear in mind that not all vessels are equipped with AIS
transponders and therefore may not be visible to this transponder. Likewise,
certain conditions, such as device malfunction, the environment, improper use,
and overcrowded port traffic, may exist whereby the vessel equipped with this
AIS transponder is not visible to other AIS transponders.
WARNING: DO NOT DISASSEMBLE OR MODIFY THE EQUIPMENT. Improper
disassembly or modification could cause personal injury and will invalidate the
guarantee.
WARNING: While most of the installation can be performed by the owner or the
crew, a final commissioning can be done by your local agent/dealer when
needed or required. AMEC and the local agent/dealer will not bear any
responsibilities over any damages resulted from improper installation by
unauthorized agent/dealer.
FOR USERS IN THE UNITED STATES OF AMERICA ONLY
WARNING: It is a violation of the rules of the Federal Communications
Commission to input an MMSI that has not been properly assigned to the
end user, or to otherwise input any inaccurate data in this device.
★ The entry of static data into this device shall be performed by the vendor
of the device or by an appropriately qualified person in the business of
installing marine communications equipment on board vessels.
★ Instructions on how to accurately enter and confirm static data in the
device can be found in this user manual.

5
FOREWORD
AMEC thanks you for the purchase of your new CAMINO-108 Automatic Identification
System (hereinafter called “AIS”). Wherever you sail now, you can have a better
control of your surrounding sea, and have an enjoyable voyage.
CAMINO-108 is strictly tested at the factory to meet the rigorous demands of the
marine environment. With proper use, installation,and maintenance, the equipment
will serve loyally and reliably at its optimum.
For sales, services, and technical supports, please contact your local AMEC
representatives or Alltek Marine Electronics Corp at [e-mail] or
[e-mail]. You are always welcome to visit our website at
www.alltekmarine.com for new product status and company update.
Thank you again. Be safe.

6
TABLE OF CONTENT
1SYSTEM OVERVIEW ................................................................................................................8
1.1 PRODUCT DESCRIPTION ......................................................................................................8
1.2 EQUIPMENTS IN THE BOX .................................................................................................. 10
1.3 EXTERNAL CONNECTIONS .................................................................................................. 11
1.4 WHAT IS AIS?................................................................................................................ 12
1.4.1 Class A vs. Class B AIS ................................................................................... 14
1.4.2 AIS Message Types........................................................................................ 15
1.4.3 AIS Report Rate............................................................................................. 15
2INSTALLATION....................................................................................................................... 16
2.1 INSTALLATION PROCEDURES ............................................................................................... 16
2.2 MOUNTING TRANSPONDER MAIN UNIT ............................................................................... 17
2.3 VHF ANTENNA INSTALLATION ............................................................................................ 19
2.4 GPS ANTENNA INSTALLATION ............................................................................................ 20
2.5 CONNECTING POWER AND DATA CABLE ................................................................................ 22
2.6 CONNECTING WITH NMEA 0183 DEVICES ........................................................................... 24
2.7 AIS SILENT MODE CONNECTION......................................................................................... 27
2.8 CONNECTION TO NMEA 2000 NETWORK............................................................................ 27
2.9 CONNECTING TO POWER SUPPLY......................................................................................... 28
3CONFIGURING YOUR CAMINO-108 ...................................................................................... 29
3.1 CONNECTING TO YOUR AIS TRANSPONDER............................................................................ 29
3.1.1 Required Items ............................................................................................. 29
3.1.2 Installing “AIS Configuration Tool” ................................................................ 30
3.1.3 Three steps to connect AIS transponder ....................................................... 30
3.1.4 Home page of the application....................................................................... 31
3.2 PROGRAMMING YOUR VESSEL DATA ..................................................................................... 32
4GET STARTED ........................................................................................................................ 34
4.1 START UP THE TRANSPONDER ............................................................................................. 34
4.2 LED INDICATORS............................................................................................................. 35

7
4.3 SD CARD DATA LOGGING .................................................................................................. 37
4.4 WI-FI CONFIGURATION (CAMINO-108W ONLY).................................................................. 38
4.4.1 Access Point Mode ....................................................................................... 39
4.4.2 Client Mode .................................................................................................. 42
4.5 BUILT-IN INTEGRITY TEST (BIIT) ......................................................................................... 44
4.6 AIS VIEWER DESCRIPTION................................................................................................. 45
4.7 CONNECTING YOUR TRANSPONDER TO MACINTOSH................................................................. 46
4.8 INTRODUCING AMEC AIS APP .......................................................................................... 46
5SPECIFICATIONS.................................................................................................................... 47
5.1 PRODUCT SPECIFICATIONS ................................................................................................. 47
5.2 DIMENSIONS.................................................................................................................. 50
5.3 NMEA 2000 PGN INFORMATION ..................................................................................... 51
5.4 SUPPORTED NMEA 0183 SENTENCES................................................................................. 53
6TROUBLESHOOTING ............................................................................................................. 54
7ABBREVIATIONS ................................................................................................................... 58
8FCC INTERFERENCE STATEMENT........................................................................................... 59
9RF EXPOSURE WARNING ...................................................................................................... 60
DECLARATION OF CONFORMITY .................................................................................................. 61
AMEC WORLDWIDE WARRANTY.................................................................................................. 61
APPENDIX: HOW TO DETERMINE SERIAL PORT ........................................................................... 63

8
1System Overview
1.1 Product Description
The AMEC CAMINO-108 AIS Class B Transponder series is perfect for smaller vessels,
where the complexity of a Class A Transponder is not necessary. It transmits the
vessels dynamic and static data in a typical 7 NM range as well as receives AIS targets
typically within 20 NM around the boat. Using the built-in GPS receiver, the
CAMINO-108 determines position, speed and course, and once this is combined with
other navigational information, it is automatically transmitted without any user
interaction. When received by other vessels and coast stations, the data built up will
provide a live graphical display of traffic in the area. The CAMINO-108 has been
engineered for flawless integration with navigation systems, and supports NMEA
2000 and NMEA 0183 communications, and its output meets IEC 62287 and related
standards.
The CE/BSH approved CAMINO-108 also features USB connectivity and an optional
Wi-Fi interface (CAMINO-108W). The SD card slot in the CAMINO-108 can be quickly
and easily used as a data recorder, enabling the capture of all messages - to assist in
system and safety monitoring, including incident investigation. The recorded data is
logged and stored on the SD card when fitted. An optional switch box enables ‘Silent’
mode allowing the user to stop the broadcast of static and dynamic information on
occasions where either privacy or security is required.

9
CAMINO-108
CAMINO-108W
Front
Back
Front
Back

10
1.2 Equipments in the Box
Upon receiving the product please verify items in the box. If any is missing, please
contact your local AMEC representative immediately.