American DJ VORTEX/G User manual

American DJ®User Manual
DMX-512
©American DJ®Los Angeles, CA 90058 - Vortex/G™ User Manual page 1
Specifications subject to change without notice.
Intelligent Lighting Fixture
SPECIFICATIONS:
Weight: 8lbs.
Size: 19.25" 8.5” x 10.75”
Lamp: EXY 82V 250W
Fuse: 5A
Supply Voltage: 120V
Working Position: Any Safe position
Colors: 8 Dichroic Colors + White
Gobos: 8 + Spot
Single Color/Gobo wheel
Introduction
Congratulations and thank you for purchasing the American DJ Vortex/G™. The
Vortex/G™ is one of the finest pieces of its kind on the market today. This unit use a
single color/gobo wheel combination for vibrant colors and extravagant gobo pat-
terns. The Vortex/G™ is a semi intelligent fixture that can run as a stand alone sound
active piece or in a master / slave mode. This fixture is sound active and can be
linked via XLR cables up to 16 pieces. The Vortex/G™ comes with several build in pro-
grams that are best used in multiples of four or more. The Vortex/G™ also offers you
the ability to run with a standard DMX controller. This piece is best used with a fog or
haze machine. The Vortex/G™comes with a swivel mirror that gives the allusion of X /
Y movement, this mirror can be adjusted by hand. The Vortex/G™ can operate in any
of three modes; Stand alone, Master/Slave, or DMX, these will be explained later in this
manual. An optional Vortex/C controller may be purchased separately that allows the
user to Black Out the Vortex/G™ when used in stand-alone or master/slave modes.
This unit is extremely light weight and compact which makes it perfect for mobile DJs,
but is also great for small club, bars, bowling centers and roller rinks.
HALOGEN LAMP WARNING!
This fixture is fitted with halogen
lamps which are highly suscepti-
ble to damage if improperly
handled. Never touch lamp with
bare fingers as the oil from your
hands will shorten lamp life. Also,
never move fixture until lamp
has had ample time to cool.
Remember, lamps are not cov-
ered under warranty conditions.
VORTEX/GTM

Operating Instructions
STAND ALONE:
1. This function allows a single unit to run to the beat of the music.
2. To activate this mode set dip switches #1and #10, on the front of unit to the ON position
(see master fixture on the DIP SWITCH chart on page 3).
3. The optional Vortex/C controller may be used for black out.
MASTER / SLAVE:
1. This function allows you to set up several units to operate without a controller.
2. The units will be sound activated and will run built in programs via an internal mic.
3. To activate this function set one unit, the master unit, dip switches as followed: Set dip
switches #1and #10 to the on position (see the chart on page 3).
4. For additional units (slaves), up to 16 units total, follow the chart on page 3
5. Connect the units together via XLR cables remembering that the Male XLR socket is IN
and the Female XLR socket is OUT.
6. The optional Vortex/C controller may be used for black out.
Note: In sound active mode the units will go in to blackout mode after 7 seconds if no
sound is present, the lamp will shut down 30 seconds later to preserve lamp life.
UNIVERSAL DMX CONTROL:
1. This function allows you to us a standard DMX controller such as the American DJ Show
DesignerTM or the American DJ DMX Operator™.
2. The use of a DMX controller will allow you to customize the use of fixtures allowing you
independent control of the colors, and mirror movement.
3. This will allow you to create your own programs or use your fixtures as spot lights.
4. The VortexTM is a two (2) channel DMX fixture; channel one controls the color/gobo wheel
and shutter, channel two controls the mirror movement.
5. When using a DMX controller and setting up for DMX operation follow the dip switch set-
tings on page 3. If starting at a higher DMX channel follow the standard DMX Binary
Code.
6. For help running in DMX operation consult the manual that comes with your DMX
controller.
LLaammppRReeppllaacceemmeenntt::Caution! Never open the unit when in use. Always disconnect
the main power before attempting to replace the lamp. Remember always replace
with the same type lamp and fuse.
Lamp replacement: Remove the two thumb screws on the cover located on the front
of the fixture. Remove and replace the lamp. Replace the cover.
The American DJ Vortex/G™ comes with a 1 year limited warranty. We recommend filling out
the warranty registration card that came with your fixture to validate your warranty. For service
contact American DJ.TM
©American DJ®Los Angeles, CA 90058 - Vortex/G™ User Manual page 2
VORTEX/G™

10
MASTER
123 54791086
ON
123 54791086
ON
123 54791086
ON
123 54791086
ON
SLAVE 1
SLAVE 2
SLAVE 3
123 547986
ON
SLAVE 4
123 54791086
ON
SLAVE 5
123 54791086
ON
SLAVE 6
123 54791086
ON
SLAVE 7
American DJ®
©American DJ®Los Angeles, CA 90058 - Vortex/G™ User Manual page 3
VORTEX/G™
Stand Alone Master/Slave Dip Switch Settings
123 54791086
123 54791086
ON
123 54791086
ON
123 54791086
ON
SLAVE 8
SLAVE 9
SLAVE 10
SLAVE 11
SLAVE 12
SLAVE 13
SLAVE 14
SLAVE 15
123 54791086
ON
123 54791086
ON
123 54791086
ON
123 54791086
ON
XLR CONNECTIONS
DATA IN
MALE XLR INPUT
3 Data +
2 Data -
1 Ground
WHITE
COLOR
CHANGE
SPEED
STROBE
IN
WHITE
MAGENTA
PINK
AMBER
GREEN
ORANGE
YELLOW
BLUE
LIGHT
GREEN
WHITE
BLACKOUT
255
254
160
159
86
78
72
60
54
44
37
26
18
9
This chart shows the value
used to set the desired effect.
The Vortex uses 2 channel
DMX per unit.
To set the DMX Channel
Use Binary Code, 1 to 8
are shown above.
When longer runs of cable are used you may need to
use a terminator on the last unit. A terminator is a 90 -
120 ohm 1/4 watt resistor which is connected between
DATA + and DATA - use an extra male Plug for this and
insert in last unit.
ON
0
CH 1 CH 2
MIRROR
MOVEMENT