American Signature Flynn Student Loft Bed User manual



red

Acon 1:
Open Boxes M, N, and Q
Follow Steps 1-4
Acon 2:
Open Boxes C, D, and Q
Follow steps 5-14 or 6A -8A & 9-14
for op�onal twin caster bed – see box 2184-330 white
for op�onal full caster bed – see box 2311-330 gray

Assembly Instructions Page 1 of 18
SAFETY WARNINGS
1. Follow the information on the warnings appearing on the upper Bunk end structure and on the
carton. Do not remove warning label from bed.
2. Always use the recommended size mattress or mattress support, or both, to help prevent
entrapment or falls.
3. Surface of mattress must be at least 5 inches (127mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper Bunk.
5. Prohibit more than one person on the upper Bunk.
6. Periodically, check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper Bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper Bunk.
11. Always use guardrails on both long sides of the upper Bunk. If bunk bed will be placed next to the
wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent
entrapment between the bed and wall.
12. The use of water or sleep flotation mattresses is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed;
including, but not limited to, hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only mattress which is inches wide on upper Bunk.
Ensure thickness of mattress does not exceed 8 inches and the mattress is at least 5
inches below upper edge of guardrails.
All Bunkbeds were
designed and manufactured with
your child's safety as our top
priority.
Their unparalleled strength is a
bi-product of the safety design.
Our bunks meet all compliance
with ASTM F 1427- "Standard
Consumer Safety Specification
for Bunk Beds"and Code of
Federal Regulations (CFR) 1213
"Safety Standards for Entrapment
Hazards in Bunk Beds "and
(CFR)1513"Requirements for
Bunks Bed".
Safety is a cooperative effort
between us as the manufacturer,
and you as a guardian. Please
read and consider the
warnings listed on this page
when choosing a mattress and
discussing rules of use with your
child.
FLYNN STUDENT LOFT BED

Assembly Instructions Page 2 of 18
FLYNN STUDENT LOFT BED
Fully Assembled
Student Loft
Enclosed please find simple step-by-step
instruc�ons to help you quickly assemble your
product. Before you begin, we recommend that
you follow the steps below:
1. Please read the instrucons thoroughly
2. Idenfy all parts and hardware
3. Gather the tool(s) necessary
4. Two adults required for assembly
To protect your parts during assembly please place


or cleaning abrasives as it will scratch the surface

CUSTOMER SUPPORT
If you are missing parts or need assistance with
your product, please contact the retailer from whom
you purchased the product. When you call or email,
please include the Product’s Item Number and PO
Number which is located on the Producon Tracking
Scker. This scker can be found on the boom,
inside or back of your product.
INTRODUCTION

Page 3 of 18
* Carton Contains Hardware Pack
MISSION STUDENT LOFT
2311-4090Q-TLLG
OPTIONAL
2184-7090Q-TLLG
OPTIONAL
G.
BOX KEY
Q
80B
M
N
BOX KEY
Q
80B
M
N
OPTIONAL:

FLYNN STUDENT LOFT BED - Assembly Instructions Page 4 of 18
PARTS LIST
HARDWARE FOR STUDENT LOFT
Ø1/4-20x90mm Bolts
X 8
Barrel Nuts
X 24
Ø10 x 40mm Wood Dowels
X 20
Allen Wrench
X1
Ø1/4-20x60mm Bolts
X 16
Ø4x30mm Wood Screws
X28
Ø4x15mm Wood Screws
X14
Bookcase
Drawer Chest
X1 Desk Top
X 1
Left & Right Desk Hutch Side Panels
X1
Bracket
X2
Bookcase
Side Panel
X 1
Bookcase
Shelves
X 2
Bookcase
Top Panel
X 1
Desk Cabinet
X1
Desk Hutch
Top Panel
X1
45mm Screws
X4
Ø8 x 40mm Wood Dowels
X 20
Ø1/4-14x20mm Bolts
X2
T-Nuts
X2
50mm Screws
X8
Ø1/4-20x35mm Bolts
X24
Box N
Box N
Box N
Box M
Box C
Box D
Box D
Box D
Box D
Box D
Box D
B
C
E
L
H
R
M
P
Q
G
U
S
K
V
Straight Allen Wrench
X 1
W
18
19
21
20
11
15
16
17
14
12 13

FLYNN STUDENT LOFT BED - Assembly Instructions Page 5 of 18
PARTS LIST (CONTINUED) Other Tools Required
(Not Included)
.Phillips Screwdriver
.Flathead Screwdriver
Ladder (LEFT)
X1
Ladder (RIGHT)
X1
Rung
X4
Box Q
Box 80B
Box Q
Box 80B
Box 80B
Box 80B
Box 80B
Box 80B
32
33
27
26
29
28
30
31

FLYNN STUDENT LOFT BED - Assembly Instructions Page 6 of 18
For left-hand Desk/Ladder
follow directions as indicated,
but please note inset drawings.
For right-hand Desk/Ladder
follow directions as indicated,
but please note inset drawings.
?
Question you must ask prior to assembly
Before beginning assembly, decide exactly where the bed is to be placed and on which
ends you would like the the Desk/Ladder and Bookcase. Both the Bookcase and Desk
can be placed at either end and reversed. See below.
You also need to decide if the desk is going to be under or outside the loft.

FLYNN STUDENT LOFT BED - Assembly Instructions Page 7 of 18
Remove drawers from chest. Switch the
knobs from inside to outside on all drawers.
Assemble Drawer Chest, Shelves
and Bookcase Side Panel
X 2
X 2
X 2
X 2
C
C
R
R
R
R
R
R
R
R
C
C
C
C
C
C
H
H
H
H
Ø1/4-20x60mm Bolts
X8
Barrel Nuts
X8
Ø1/4-20x35mm Bolts
X9
Wood Dowels
X8
Ø8x40mm
C
E
H
R
STEP 2
STEP 1
Allen Wrench
X1
V
Straight Allen Wrench
X 1
W
Open Boxes M, N, and Q for Steps 1-4
Chest
Assembly
20
18
18
19
19

FLYNN STUDENT LOFT BED - Assembly Instructions Page 8 of 18
Attach Head/Footboard to Bookcase Top Panel then attach Top Panel to Bookcase.
Left Side Chest Set Up Right Side Chest Set Up
STEP 4
With two adults, lift the Bookcase into desired position
then replace the Drawers.
STEP 3
E
E
E
EE
EEEE
Chest
Assembly
32
32
21
21

FLYNN STUDENT LOFT BED - Assembly Instructions Page 9 of 18
NOTE:
Choose for desk to
be inside facing or
outside facing.
!
Ø1/4-20x60mm Bolts
X8
Barrel Nuts
X8
Ø1/4-20x35mm Bolts
X8
Wood Dowels
X12
Ø8x40mm
C
E
H
R
45mm Screws
X 4
L
Ø1/4-14x20mm Bolts
X 2
T-Nuts
X 2
G
U
Allen Wrench
X1
V
Straight Allen Wrench
X 1
W
NOTE: Before continuing assembly, decide whether
you would like the Desk to be outside-facing of
inside-facing and follow instructions below .
For inside-facing Desk
assembly, please skip to
Step 6A on Page 12
For outside-facing Desk
assembly, please continue with
Step 5 on Page 10
Open Boxes C, D, and Q for Steps 5-11
Desk
Assembly

FLYNN STUDENT LOFT BED - Assembly Instructions Page 10 of 18
Fit Desk Hutch Back Supports, Desk Top, and
Left Desk Hutch Side Panel together using wood
dowels(12).
Steps 6-8: Outside-facing Desk assembly
STEP 6
STEP 5
x 2
x 2
Remove Drawers from Desk Cabinet before proceeding, then attach Right
Desk Hutch Side Panel
R
R
R
R
R
R
E
E
Desk
Assembly
Outside
Facing Desk
13
13
12
15
14
11
11
16

FLYNN STUDENT LOFT BED - Assembly Instructions Page 11 of 18
Desk
Assembly
Outside
Facing Desk
STEP 7 STEP 8
Skip to Step 9 on Page 13
12
12
13 17
13

FLYNN STUDENT LOFT BED - Assembly Instructions Page 12 of 18
Fit Desk Hutch Back Supports, Desk Top, and
Left Desk Hutch Side Panel together using
wood dowels(12).
Secure Desk Hutch Side Panels and Back
Supports as shown.
Attach Desk Hutch Top Panel.
STEP 6A STEP 7A STEP 8A
Steps 6A-8A: Inside-facing Desk assembly
R
R
R
R
R
R
E
E
LLL
E
E
H
H
H
H
H
L
H
U
U
H
G
C
C
C
C
C
G
C
C
Desk
Assembly
Inside
Facing Desk
11
16
15
13 13
12 12
17
14

FLYNN STUDENT LOFT BED - Assembly Instructions Page 13 of 18
Inside Desk Set Up
Outside Desk Set Up
Attach Headboard to the
top of the Desk Hutch.
Steps 9-14: Upper Bed assembly
Loosely attach Desk Hutch,
Bed Side Rails and Bookcase
(do not completely tighten
bolts until Step 14).
STEP 9
STEP 10
Q
H
B
EEEE
EEEE
32
32
32
32
32
26
26

FLYNN STUDENT LOFT BED - Assembly Instructions Page 14 of 18
Note: Upper Bed the detail and Hardware in X080 Box
Attach Slats.
STEP 11
M
MM
33
33

FLYNN STUDENT LOFT BED - Assembly Instructions Page 15 of 18
Note: Upper Bed the detail and Hardware in X080 Box
Position Guard Rails in place, tighten all Bed Side
Rail bolts completely, then attach Guard Rails as
shown. Note: Ladder opening must be on the Desk
end of the bed.
STEP 12
P
M
E
P
27 27
27
28

FLYNN STUDENT LOFT BED - Assembly Instructions Page 16 of 18
STEP 13
S
P
P
P
Q
K
K
K
V
V
S
Note: Upper Bed the detail and Hardware in X080 Box
29
30 31

FLYNN STUDENT LOFT BED - Assembly Instructions Page 17 of 18
Inside detail
Attach Ladder Hooks to Ladder, then attach Ladder to Upper Bed
Note: Please ensure that
the bolts for Ladder rungs
are tight before using.
STEP 14
P
P

Page 18 of 18
Note: Upper Bed the detail and Hardware in X080 Box
!WARNING
Important Safety Notice
  


these simple rules:
   
   
   
   
   
   
   
   
   
   
   
fastened to the dresser according to the
   
  
   
CARE INSTRUCTIONS
A lacquer finish is used on this furniture to protect the wood. It is not
waterproof, clean spills immediately. Dust using a slightly damp cloth,
making sure no standing water is le on the furniture. DO NOT use any
household cleaners, citrus-based polishes, wood soaps, or oils; they can
break down the natural lacquer finish.
Do not place furniture in direct sunlight. Natural solid wood furniture will
naturally color as it ages, however, direct sunlight dramacally speeds up
the process.
In natural wood furniture, the variaons in texture and grain will affect
the finish, making it impossible to guarantee an exact match between two
pieces of wood even though idencal finishing processes are used. These
differences in character are not defects, but variaons that make each
piece of furniture unique and beauful.
Solid wood naturally expands and contracts. In high humidity you may
find that drawers can sck slightly. This will correct itself, and is not reason
for concern.
Do not place furniture over heang or cooling vents. Dramac changes
in temperature can cause the wood to split.
If you place objects such as lamps of plants on your case pieces make sure
to move them from me to me. There may be a slight discoloraon where
the object was. However by exposing it to the light the color will catch up
the rest of the case.
Plasc or foam footed items such as phones or clocks can damage this
finish, use trivets under such items.
•
•
•
•
•
•
•

Page 1 of 5
FLYNN TWIN LOWER COMPLETE BED WITH CASTERS