American Standard Lifetime 2771L User manual

HD-5
© 2007 American Standard Inc.
LIFETIME™ 5' X 36"
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
LIFETIME™ 5' X 36"
Comfortable bathing design with form-tted backrest
and molded-in armrests.
❏ Model# 2771L (specify color)
• Acrylic with berglass reinforcement
• Lifetime Overow Drain for maximum
water depth
• 1.4 HP self-draining pump/motor with dry
run seal
• Eight ow adjustable jets including:
Two adjustable Ideal Flow Comfort Jets™
Six adjustable Comfort Jets™
• Two silent air volume controls
• Side-mounted On/Off control
• Complete factory installed and tested
whirlpool system
• Self leveling feet
• Designed with undermount installation option
❏ Model# 2771LC (specify color)
• Same as above with the EverClean™ whirlpool
system. The EverClean™ antimicrobial system
incorporates AlphaSan®, a patented
antimicrobial agent manufactured right into the
circulation system components, which
suppresses the growth of unsightly algae,
fungus, mold and mildew.
❏ Model# 2771L.002 Bathing Pool Only
Nominal Dimensions:
60” x 36” x 19-3/4”
(1524 x 914 x 502mm)
Compliance Certications -
Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
AND PRODUCT SPECIFICATIONS
Components Required:
❏ Bath Filler*: (specify nish)
❏ Bath Drain: 1599.205.XXX (specify color)
OR 1599.500.020 (white only)
❏ Five Foot Apron: 9261.019.XXX (specify color)
❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100
❏ Tile Bead Kit: TILE-BEAD
Revised 7/07
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not heat
cold water to desired bathing temperature.
* See American Standard Faucet Selector
AlphaSan® is a registered trademark of Milliken & Co.

HD-6
© 2007 American Standard Inc.
LIFETIME™ 5' X 36"
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
Revised 7/07
60"
(1524mm)
36"
(914mm)
36"
(914mm)
3"
(76mm)
7-1/2"
(191mm)
6"
(152mm)
11"
(279mm)
13-3/4"
(349mm)
21-1/2"(H)
(546mm)
20"(C)
(508mm)
20-1/8"(A)
(511mm)
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.
C/L OF
OVERFLOW
CUT OUT IN FLOOR
FOR DRAIN
60 x 36 x 21-1/2 In.
(1524mm x 914 mm x 546mm)
75 Lbs. (34 Kg.)
800 Lbs. (363 Kg.)
87 Gal. (329 L.)
50 Gal. (189 L.)
41-1/4 x 26-1/4 In.
(1048mm x 667mm)
52-1/2 x 30 In. (1334mm x 762mm)
18-1/2 In. (470mm)
53 Lbs./Sq. Ft. (260 Kgs/Sq. m.)
GENERAL SPECIFICATIONS FOR 2771L WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.4 HP, 9.7 AMPS, 120V.PUMP
Whirlpool Shown
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUPPORT OF
BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3 WALL TILING BEAD. KIT No. TILE-BEAD AND APRON No. 5FT-APRON AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet