American Standard Scala Corner Whirlpool and Bathing Pool... User manual

SCALA CORNER™
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
SCALA CORNER WHIRLPOOL & BATHING
POOL
❏2664.118 Whirlpool with right hand drain outlet
❏2664.218 Whirlpool with left hand drain outlet
•Acrylic with fiberglass reinforcement
•Factory installed and tested whirlpool
system
•1.0 HP single speed self-draining pump/motor
with dry run seal
•Six multi-directional and individually flow-rate
adjustable color-coordinated jets
•Two color-coordinated air volume controls
•Anti-vortex suction fitting
•Deck-mounted color-coordinated air switch
On/Off control
•U.L.®Listed Hydromassage bathtub
•Textured tub bottom pattern
•Integral sump support feet
•Factory installed power cord with plug
•Dual molded-in lumbar support
•Molded-in seat
•Molded-in water retention flange
❏2664.102 Bathing Pool only with Right-hand
Drain Outlet
❏2664.202 Bathing Pool only with Left-hand
Drain Outlet
Nominal Dimensions: 1524 x 1524 x 502mm
(60”x 60”x 19-3/4")
© 2002 American Standard Inc. BV-029
SPS 2664
To Be Specified - Required:
❏Bath Filler*
❏Drain: 1553.270 (specify Chrome , Polished Brass
or Satin)
❏Color:
To Be Specified - Optional:
❏Metal Air Volume Control Kit: 9850.200-two
per kit (specify Chrome, Polished Brass or Satin)
❏Metal Jet Trim Ring Kit: 9860.200-two
per kit (specify Chrome or Polished Brass or Satin)
* See faucet section for models available
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Revised 3/98
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
•ASME A112.19.7M for Whirlpool Appliances
•ANSI Z124.1 for Plastic Bathtubs
•ASTM E162 for Flammability
•NFPA 258 for Smoke Density

SCALA CORNER™
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2002 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED.
ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CONCEALED PIPING NOT INCLUDED.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE
WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES
DRILLED BY INSTALLER.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
●
■
552mm
(21-3/4)
140mm(5-1/2)
1080mm
(42-1/2)
1524mm
(60) TYP.
1041mm
(41)
775mm
(30-1/2)
PROVIDE ACCESS
FOR SERVICING
PUMP & CONTROLS
216mm
(8-1/2)
406mm
(16)
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
19mm(3/4)
CUTOUT DIMENSION
1632mm
(64-1/4)
1505mm (59-1/4) TYP.
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
1600mm
(63-1/2)
1356mm
(53-3/8)
OF DRAIN OUTLET
C
L
ROUGH
FLOOR
502mm
(19-3/4)
464mm
18-1/4
38mm
(1-1/2)
13mm (1/2) INTEGRAL
TILE FLANGE
1-1/2" O.D. TAILPIECE INTEGRAL
FEET
SUPPORT
LEVELING
STRINGER
(NOT FOR
SUPPORT) 1-1/2" N.P.T.M. THREADS
60mm
(2-3/8)
124mm
4-7/8
95mm
(3-3/4)
724mm(28-1/2)
ON/OFF
SWITCH
RECOMMENDEDFITTINGLOCATION
64 X 279mm(2-1/2 X 11)
●
1041mm
(41)
775mm
(30-1/2)
552mm
(21-3/4)
140mm (5-1/2)
1080mm
(42-1/2)
1524mm
(60) TYP.
216mm
(8-1/2)
406mm
(16)
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
19mm(3/4)
CUTOUT DIMENSION
1632mm
(64-1/4)
1505mm (59-1/4) TYP.
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
1600mm
(63-1/2)
1356mm
(53-3/8)
OF DRAIN OUTLET
C
L
ROUGH
FLOOR
502mm
(19-3/4)
464mm
18-1/4
38mm
(1-1/2)
13mm (1/2) INTEGRAL
TILE FLANGE
1-1/2" O.D. TAILPIECE INTEGRAL
FEET
SUPPORT
LEVELING
STRINGER
(NOT FOR
SUPPORT) 1-1/2" N.P.T.M. THREADS
60mm
(2-3/8)
124mm
4-7/8
95mm
(3-3/4)
724mm (28-1/2)
RECOMMENDED FITTING LOCATION
64 X 279mm (2-1/2 X 11)
●
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
114 Lbs. ( 51 Kg.)
781 Lbs. (351 Kg.)
80 Gal. (303 L)
58 Gal. (220 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
37 Lbs./Sq.Ft. (182 Kgs./Sq.m)
41.7
68.4
GENERAL SPECIFICATIONS FOR 2664 WHIRLPOOL
1.0 HP, 9.9 AMPS,120V.
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
94 Lbs. (42 Kg.)
761 Lbs. (342 Kg.)
80 Gal. (303 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
36 Lbs./Sq.Ft. (177 Kgs./Sq.m)
41.7
68.4
GENERAL SPECIFICATIONS FOR 2664 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)