American Standard 8630 Series User manual

Installation
Instructions
M968716 Rev.1.1
8630 SERIES
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
SHOWER
HEAD
SHOWER
ARM
UNION
SWIVEL
COUPLING
NUT
PLASTER
GUARD
"COLD"
"HOT"
RUBBER
RING
SLEEVE
VALVE
COVER
ESCUTCHEON
TRANSFER
VALVE
(2) 1-13/16" DIA. HOLES
FOR VALVES ON 8"
CENTERS (1) 1-13/16"
DIA. HOLE FOR CENTER
TRANSFER VALVE
CROSS
BRACE
FINISHED
WALL
1-1/4 DIA HOLE
1-3/4
TO
3-3/8
OPTIONAL
TO FINISHED
FLOOR USUALLY
BETWEEN
65'' AND 78''
1/2" N.P.T.
SHOWER ARM
1-1/2
ROUGHING-IN DIMENSIONS
7 REF.
1-3/4
TYP.
1-3/4
UNION INLET
1/2"-14 N.P.T.
1/2" N.P.T. TO
SHOWER
9 REF.
74 FOR HEAD CLEARANCE
(OPTIONAL)
48
OPTIONAL
to
FINISHED
FLOOR
NOTE: NO CONCEALED PIPING FURNISHED
SPOUT
1-1/2"
4"
1/2" N.P.T.
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
5"
REF.
VALVE
STREAM
STRAIGHTENER
HANDLE
ADAPTER
FINISHED
FLOOR
TUB RIM
THREE HANDLE
BATH/SHOWER SETS with EverClean™ Finish
Congratulations on purchasing your American Standard faucet with
EverClean nish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel,
Polished Brass (or any combination of these nishes)

IN MEXICO 01-800-839-12-00
M968716 Rev.1.1
Turn off hot and cold water supplies before beginning.
CAUTION
5
TEST INSTALLED FAUCET
4
Turn HANDLES into "off" position.
Turn on water supplies and check all connections for leaks.
Operate both HANDLES to flush water lines thoroughly.
Check SHOWER HEAD and connections for leaks.
Turn handles into OFF position.
1
ROUGHING-IN FITTING
ROUGHING-IN SHOWER AND SPOUT
2
Prepare water supplies per "Roughing-in Dimensions."
Install VALVE at indicated height and depth. Notice that finished wall has
to be between the MAX WALL and MIN. which is 1-5/8" below.
Slip COUPLING NUT over supply pipe and screw UNION SWIVEL
to pipe.
For Sweat Connection: Slip COUPLING NUT over 5/8" O.D.
supply tube and solder tube into UNION SWIVEL or female inlet
of valve.
Connect HOT water supply to left VALVE inlet and COLD water
supply to right VALVE inlet. Tighten both COUPLING NUTS firmly.
Secure VALVE BODY to cross brace of wall structure.
ELBOW
ROUGH-IN
NIPPLE
TUB
FILLER
PIPE
SPOUT
3FINISHING INSTALLATION
Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 2000
SERVICE
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90$and replace.
Replace SPRING CLIP.
Reinstall HANDLE. (See step 4).
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90$.
SPRING
CLIP
STOP
WASHER
90$
CROSS
BRACE
UNION
SWIVEL
SUPPLY
PIPE
COUPLING
NUT
"HOT"
"COLD"
"MAX
WALL"
PLASTER
GUARD
ROUGH-IN
NIPPLE
ELBOW
Install SHOWER ARM, SHOWER ARM FLANGE and TUB SPOUT.
Remove caps from roughing-in nipples.
Remove PLASTER GUARD by turning counter-clockwise and pulling.
If VALVE BODY is roughed in deep (more than 1-1/2") screw
SLEEVE in ESCUTCHEON facing front of ESCUTCHEON.
If VALVE BODY is roughed in SHALLOW (less than 1-1/2")
screw SLEEVE in ESCUTCHEON facing back of ESCUTCHEON.
Assemble RUBBER RING to ESCUTCHEON.
Screw ESCUTCHEON and SLEEVE onto VALVE COVER against wall.
SHALLOW ROUGH-IN
LESS THAN
1-1/2"
SLEEVE
SLEEVE
MORE THAN
1-1/2"
ESCUTCHEON
RUBBER
RING
DEEP ROUGH-IN
VALVE
BODY
VALVE
COVER
Prepare SHOWER RISER, ELBOW, and roughing-in NIPPLE and
connect to top outlet of VALVE BODY. Outlet is 1/2" female NPT.
Add cross braces to wall structure and secure piping.
Prepare TUB FILLER PIPE, ELBOW and 1/2" NPT SPOUT NIPPLE.
Final length of SPOUT NIPPLE to be 1-1/2" from finished wall.
Cap roughing-in nipples, open supply lines and check for leaks.
Close both valves, turn off water supplies, and replace PLASTER GUARDS.
Finish wall construction.
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
STEM
SOCKET
PLASTER GUARD has a STEM SOCKET to operate valves.
Turn PLASTER GUARD over and push STEM SOCKET onto VALVE STEM.
Open hot and cold valves and check for leaks.
Remove PLASTER GUARDS by turning counter clockwise and pulling. (Do not discard).
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
SHOWER
ARM
SHOWER
HEAD