American Standard Princeton Collection User manual

Installation
Instructions
T508.900
Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
Drill with 3/16" bit
1SPOUT INSTALLATION
Complete FINISHED DECK before trim installation.
Turn off the water supplies.
Remove the GUARDS (1) from the VALVE BODIES (2). Remove the
GUARD (3) and 1/4" PLUG (4) from the SPOUT SHANK (5).
The SPOUT SHANK (5) height should be 1" to 2" above the
FINISHED DECK. Cut the SPOUT SHANK (5) if necessary.
Remove all burrs and bevel the end of the shank. Failure
to do so may damage the SPOUT O-ring during installation
and cause water leakage.
Drill a 3/16" hole in the finished deck for spout locking pin. See
TEMPLATE for location.
3/16" DRILLED
HOLE
5
FINISHED
DECK
REMOVE ALL
BURRS AND
BEVEL
1"- 2"
3
4
5
1
1
2
Flat Blade Screwdriver
Adjustable Wrench Channel Locks
Phillips Screwdriver
Required Tools
PRINCETON™
DECK MOUNT TUB
FILLER TRIM KIT
M968844 REV.1.4
TEMPLATE FOR
SPOUT ROLL
PIN LOCATION
3/16" DIA. HOLE
8.4mm
(21/64")
19.8mm
(23/32")
FRONT
18.6mm DIA.
(47/64")
SPOUT SHANK
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

Position the RUBBER RING (14) in the groove in the base of the SPOUT (12).
Push the SPOUT (12) with ESCUTCHEON (11) down onto the SPOUT
ADAPTER (8) and tighten the SET SCREW (13) securely with the
5mm HEX KEY (15) supplied.
Lubricate the SPOUT ADAPTER O-RING (6) and
SPOUT O-RING (7).
Push SPOUT ADAPTER (8) on SPOUT SHANK (5) and
align slot in SPOUT ADAPTER (8) with 3/16" drilled hole.
Tighten SPOUT ADAPTER SET SCREW (9) securely
with 4mm HEX KEY (10) supplied.
GROOVE
GROOVE
FINISHED
DECK SLOT
3/16" DRILLED
HOLE
6
10 8
8
7
7
5
11
13
12
15
9
12
14
14
2INSTALL HANDLE ADAPTERS
Place the ESCUTCHEON SEALS (1) into groove of DECK ADAPTERS (2).
Align the HANDLE STEM (3) with the SLEEVE (4) as necessary.
Thread the HANDLE ADAPTER (5) into the VALVE BODY (6) until the
DECK ADAPTERS (2) contacts tight against the finished deck. GROOVE
1
6
5
4
2
3
M968844 REV.1.4
1A SPOUT INSTALLATION

4
6
5
TESTING SERVICE
Turn the HOT HANDLE clockwise and the COLD
HANDLE counterclockwise to the off position.
Unscrew and remove the STREAM STRAIGHTENER.
Slowly turn on the water supplies.
Operate the HANDLES to flush water lines thoroughly.
Check SPOUT connection for leakage.
Turn the Handles off. Replace the SPOUT END.
HOT
HANDLE
COLD
HANDLE
VALVE
CARTRIDGE
Turn off the water supplies
Turn HANDLE (1) to the off position.
Unthread the HANDLE BASE (2) from HANDLE ADAPTER (3).
Unthread HANDLE ADAPTER (3) and remove.
Remove VALVE LOCKNUT (4). A 17mm deep socket
is required.
Remove the CARTRIDGE (5) by
pulling up on the SLEEVE (6).
Remove SCREW (7) and pull off
SLEEVE (6).
Remove the SPRING CLIP (8).
Remove the STOP WASHER (9).
Turn it 90˚ and replace.
Replace the SPRING CLIP (8).
Reverse the above steps to
reassembly the components.
If the spout drips, operate the handles several
times from the off to the on position. Do not
force - the handles only turn 90˚
90˚
To change the direction of handle rotation
STREAM
STRAIGHTENER
1
3INSTALL HANDLES
Push ADAPTER (1) on VALVE STEM (2) so that the hole of the ADAPTER (1)
without a spline is facing up. See Figure "A". Tighten STEM SCREW (3) to
secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male
teeth on ADAPTER (1) to female teeth in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) until snug
against mounting surface. Repeat steps for opposite handle.
1
3
9
2
4
7
6
8
5
4
2
5
3
TOP
Figure "A"
SPLINE
END DOWN
THREAD ON
TO DECK
ADAPTER
EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
M968844 REV.1.4