American Standard FLUENT 7186.801 User manual

12
13
SPOUT BASE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert (1) CABLE CONNECTOR (2) and HOSE (3) through center hole,
making sure SEAL WASHER (4) is properly seated in spout base.
Assemble RUBBER WASHER (5), LOCKNUT (6) and thread LOCKNUT (6)
onto SHANK (7) from underside of sink or mounting surface.
Align and center SPOUT (1). Tighten LOCKNUT (6).
1
1A
7186.801
7186.811
Certified to comply with ANSI A112.18.1
Installation
Instructions
Wide Spread Lavatory Faucet
with Speed Connect®Drain
INSTALL SPOUT
INSTALL VALVE BODIES
4
Remove LOCKNUT (8) and RUBBER WASHER (9) from
SIDE VALVE SHANKS (10).
Insert Hot and Cold SIDE VALVE HOSES (11), FLEXIBLE
SUPPLIES (11a) into mounting holes making sure the SEAL
WASHERS (12) are properly seated in each HANDLE BASE (13).
Assemble RUBBER WASHER (9) and thread
LOCKNUT (8) onto each SIDE VALVE
SHANK (10) from underside of sink
or mounting surface.
Align and center SIDE VALVES.
Tighten LOCKNUTS (8).
Adjustable WrenchFlat Head Screwdriver Slip Jaw Pliers
Recommended tools
Tubing Cutter
Fig. A.
Fig. A.
Fig. B.
Fig. B.
1
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
1
11 Blue Stripe (C0LD)
11 Red Stripe (HOT)
2
3
6
5
7
8
11a
11a
9
10
M965622 Rev. 1.2 (12/17)
FLUENT®

2
6
POP-UP KNOB (2) must be fully down. Fig. B.
FLANGE GASKET AND POP-UP KNOB Fig. A. Fig. B.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (1) is fully compressed
and not visible. Fig. A.
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
2
4
3
TIGHTEN LOCKNUT
1
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
2
3
3
1
1
INSTALL DRAIN FROM
BELOW FIXTURE 5
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
4
Fig. A.
Fig. A. Fig. B.
2
DRAIN
OUTLET
1
3
4
REAR OF SINK
DRAIN
BODY
4
DRAIN
FLANGE
DOWN
Fig. B.
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Slip Jaw Pliers.
WHITE FOAM
GASKET
NOT VISIBLE
2
1
M965622 Rev. 1.2 (12/17)

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly, refer
to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
8
3
ATTACH CABLE CONNECTOR
7
2
1
1-1/4” O.D.
2
1
Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer
must purchase additional parts separately.
Important: If FLEXIBLE SUPPLIES (1, 2) are to long,
loop to avoid kinking.
Connect 1-1/4" O.D. tailpiece on POP-UP DRAIN to
waste outlet.
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on fitting supplies is 3/8" compression. Connect
FLEXIBLE SUPPLY (1) (Marked with a Red Band) to the Left wall supppy and
FLEXIBLE SUPPLY (2) (Marked with a Blue Band) to Right wall supply.
9
Connect the VALVE HOSES (3, 3a) to SPOUT TEE (4).
Use adjustable wrench to tighten connections.
Do not over tighten.
MAKE WATER SUPPLY AND WASTE CONNECTIONS
Fig. A. Fig. B.
WASTE
OUTLET
HOT
COLD
1
3
3a
42
Blue Stripe
(C0LD)
Red Stripe (HOT)
Thread CABLE CONNECTOR (1) clockwise
onto CABLE ATTACHMENT POINT (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
M965622 Rev. 1.2 (12/17)

CHECK DRAIN CONNECTIONS
10
11
12
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate both HANDLES (1) to flush water
lines thoroughly.
Replace AERATOR (3).
Operate POP-UP KNOB (5) and fill Sink with water. Check
that DRAIN STOPPER (4) makes a good seal and retains
water in Sink. If STOPPER (4) does not seal properly, please
refer to “Troubleshooting Guide” in these instructions.
Release POP-UP KNOB (5) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
4
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
90˚
90˚
4
HOT
13
SERVICE
To change direction of handle:
1
1
COLD
2
2“P”TRAP
5
WASTE
OUTLET
3
6
7
1
23
4RED
5BLUE
8
9
9
Turn valves to OFF position.
Turn off water supplies.
Loosen SET SCREW (1) with 5/64" HEX WRENCH (2).
Pull HANDLE (3) “UP” firmly to release from
PLASTIC INSERT (4, 5 or 6).
Remove SCREW (7) and pull off PLASTIC INSERT
(4, 5 or 6).
Remove RETAINING O-RING (8).
Lift and turn STOP WASHER (9) 90˚.
Replace RETAINING O-RING (8).
Re-install HANDLE ASSEMBLY.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse to clear any debris.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
M965622 Rev. 1.2 (12/17)

M965622 Rev. 1.2 (12/17)
Fig. F.
5
Speed Connect®Drain
Troubleshooting Guide
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
CAM
CAM CAP
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig. B.Fig. A.
REMOVE
CAM
Fig. E.
STOPPER REMOVAL PROCEDURE
2
1
RE-ATTACH
DISCONNECT
Fig. D.
REMOVE
CAM CAP
STOPPER
Fig. C. DOWN
CABLE ADJUSTMENT PROCEDURE
Disconnect the Cable from the Drain by threading the CABLE CONNECTOR (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small flat head screwdriver to fully rotate the Cam in the clockwise direction. At this point the
Stopper should be in the UP position. Fig. B, C.
Make sure the LIFT KNOB (3) it is fully down. Fig. C.
Re-attach the CABLE CONNECTOR (1) to the CABLE ATTACHMENT POINT (2) by threading the CABLE
CONNECTOR (1) clockwise onto the CABLE ATTACHMENT POINT (2) and hand-tighten. Fig. A.
3

M965622 Rev. 1.2 (12/17)
LOOP TOWARD
REAR OF SINK
Fig. G.
LOGO
STOPPER INSTALLATION PROCEDURE
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode
(Vandal Proof)
Unlocked Mode
DRAIN
6
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
Fig. G.
LOGO
DRAIN
LOOP TOWARD
FRONT OF SINK
180˚

M965622 Rev. 1.2 (12/17)
7
M961634-0070A
VALVE
MOUNTING KIT
MODEL NUMBERS
CHROME
SATIN NICKEL
LEGACY BRONZE
002
295
278
Replace the "YYY" with
appropriate finish code
7186.801
7186.811
M964919-YYY0A
LEVER HANDLE (LEFT)
M964920-YYY0A
LEVER HANDLE (RIGHT)
M952430-0070A
CABLE ASSEMBLY
M952425-YYY0A
DRAIN ASSEMBLY
M964922-YYY0A
HANDLE BASE
M904924-0070A
CARTRIDGE NUT
M964005-0070A
CARTRIDGE
Wide Spread Lavatory Faucet
with Speed Connect®Drain
M964923-YYY0A
LIFT ROD AND KNOB
M904521-0070A
T-CONNECTOR
M964479-0070A
AERATOR (1.2 GPM)
A911757-0070A
SEAL
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
FLUENT®