American Standard 2664 User manual

754532-100 Rev. A
1
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool
and air bath versions are completely assembled with pump/blower and system piping. All you need to finish the
installation are your selected fittings and electrical connections.
To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
© AS America, Inc. 2010
All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.
For questions or service issues, please call Technical Support 1-(800)-442-1902.
Please do not contact or return product to the store.
MODEL 2664
MODEL 2709
MODEL 2711
MODEL 2742
MODEL 2748
MODEL 2806
MODEL 2903
MODEL 2908
MODEL 2932
MODEL 2933
MODEL 2934
MODEL 2935
MODEL 2938
MODEL 2939
MODEL 2940
MODEL 2941
MODEL 2942
MODEL 2943
MODEL 2944
MODEL 2945
MODEL 3571
MODEL 3572
MODEL 3573
MODEL 3574
MODEL 3575
MODEL 3581
MODEL 3582
MODEL 3583
MODEL 3584
MODEL 6060
MODEL 7236
INSTALLATION AND
OPERATION MANUAL
BATHTUBS, WHIRLPOOLS, AIR BATHS
AND COMBINATION TUBS WITH
OPTIONAL CHROMATHERAPY

2
754532-100 Rev. A
TABLE OF CONTENTS:
Cover ................................................................................................Page 1
Table of Contents ..............................................................................Page 2
Safety Instructions Notice.................................................................Page 3
Installation, Framing and Post Installation
Clean-Up Instructions.......................................................................Page 4
Roughing-in References for Recess Type Installations.....................Page 5
Roughing-in References for Pier Type Installations...........................Page 6
Under Deck Mounting Instructions....................................................Page 6
Roughing-in References for All Model Series...................................Pages 7 - 26
Electrical Installation Instructions .....................................................Pages 27 - 32
Whirlpool Heater Operation ...... ..........................................................Page 32
Remote Air Blower Location Option..................................................Pages 33 - 34
Operation: Single Speed Whirlpool...................................................Page 35
Operation: EcoSilent Whirlpool with Lights.......................................Page 36
Operation: Air Bath............................................................................Page 37
Operation: Air Bath with Lights..........................................................Pages 38 - 39
Operation: Combination Tub with Lights...........................................Pages 40 - 41
Cleaning and Maintenence...............................................................Page 42
Warranty
...................................... .....................................................Page 43

754532-100 Rev. A
3
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS!
!
!
!
!
!
!
WARNING: Risk of personal injury. Do not permit children to use this bathtub without adult supervision. Never drop or
insert any object into any opening. Do not operate this unit without the guard over the suction fitting.
WARNING: Risk of electric shock. Do not permit electrical appliances near any bathtub when bathtub contains water.
WARNING: Risk of hyperthermia and possible drowning. People using medications and/or having adverse medical
history should consult a physician before using this product.
WARNING: Risk of personal injury. Do not overfill bathtub before entering. Entering tub when filled more than 2/3 can
cause overflow and slippery conditions. Exercise caution when entering and exiting.
WARNING: No Food or Alcoholic Beverages. Use of your bathtub immediately after meals is not recommended. Avoid
alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or hyperthermia resulting in loss of
consciousness or even drowning.
WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub.
Use this unit only for its intended use as described in this manual.
Do not use any attachments not recommended by American Standard.
The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter (GFCI). Such a
GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The
GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the
GFCI is defective. If the GFCI interrupts power to the bathtub without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this air bath. Disconnect the air bath and have the problem corrected by a
licensed electrician before using.
SAVE THESE INSTRUCTIONS

4
754532-100 Rev. A
Each bath arrives ready for installation, completely equipped with the pump/blower electronics
and plumbing necessary for operation. However, a drain/overflow kit is required for each bath
and it is not included.
The variety of installations for this bath may require framing procedures other than those shown.
Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square.
Installation and Framing Instructions
Remove the bath from the carton. Retain the shipping carton until satisfactory
inspection of the product has been made. Do not lift the bath by the plumbing at
any time; handle by the shell only.
All bath units are factory tested for proper operation and watertight connections
prior to shipping. Prior to installation, the bath must be filled with water and
operated to check for leaks that may have resulted from shipping damage or
mishandling.
The sumps of these baths are supported by feet and no additional sump
support is required. Once the bath is in place, the feet should be shimmed and
secured accordingly so that the rim of the bath contacts the stringer or pier but
supports no weight.
Provisions must be made in all installations for an access opening for servicing the
bath pump/blower. Unless an access opening of at least 12" x 24" (305mm x 610mm)
is provided, warranty service will not be performed. It is strongly recommended that an
additional opening be provided for access to drain components.
Each bath has a nominal length (L), width (W), and Height (H) along with a rim
height. Unless otherwise noted in the following rough-in references, assume
that the nominal tolerances are as much as +/-1/4 inch (6mm). Therefore, it is
strongly recommended that the installer build the surrounding structure after
receiving the actual bath. Structural measurements should be verified against
the actual bath received to ensure proper fit.
!
!
!
!
!
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden
popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid
dishwashing detergent.
Stubborn dirt or stains may be removed using granular Spic and Span®mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

754532-100 Rev. A
5
ROUGH-IN REFERENCES FOR RECESS TYPE INSTALLATIONS
TILE
TILE
BEAD
STRIP
LEVELING STRINGER
1" x 4" (25mm x 102mm) not for support
BATH
ADHESIVE
SEALANT
WALLBOARD
NOTE: Tile bead kit not included and must
be purchased separately.
SECURE THE BATH TO THE STUDS AS SHOWN
FOR WOOD OR STEEL STUD CONSTRUCTION.
TYPICAL TILE FLANGE INSTALLATION TYPICAL TILE BEAD INSTALLATION
STUD
WATERPROOF DRYWALL
OR CEMENT BOARD
WATERPROOF DRYWALL
OR CEMENT BOARD
TILE
SEALANT
TUB
ROOFING NAIL
1" x 3" (25 x 76mm) WOOD
STRINGER FULL LENGTH
1" x 3" (25 x 76mm) WOOD
STRINGER FULL LENGTH
STEEL
STUD
WASHER
TILE
SEALANT
TUB
4" (102mm)
DRYWALL
SCREW
STEEL
STUDS
WOOD
STUDS
24"
(610 mm)
12"
(305 mm)
C
E
D
W
LEVELING
STRINGERS
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON
PUMP/MOTOR END FOR SERVICE.
UNLESS AN ACCESS OPENING OF AT LEAST 12" x 24" (305 x 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
NOTE:
FRONT EDGE
OF BATH MUST
BE SUPPORTED
BY STUD WALL OR
AMERICAN STANDARD
APRON KIT
ACCESS PANELS NOT
REQUIRED FOR BATH TUBS

6
754532-100 Rev. A
Please note that care must be taken to protect the surface of the tub during all aspects of the installation.
Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result.
1. Install the tub per the installation instructions provided with the unit.
2. Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting.
3. Cut bath deck to your specifications.
4. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath
deck with the tub directly beneath it as damage to the tub may result.
5. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line.
6. Replace the bath deck and secure it into place.
7. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal.
8. Remove excess sealant per the manufacturer's instructions.
Finished bath deck surface material must be
self-supporting and secured per local codes
Tub support structure per installation
instructions provided with the tub
Bath deck support material
Bathtub
Waterproof
Sealant
UNDER DECK MOUNTING INSTRUCTIONS
ROUGH-IN REFERENCES FOR PIER TYPE INSTALLATIONS
AS DESIRED
F
CUTOUT
AS DESIRED
G
CUTOUT
C
24"
(610 mm)
12"
(305 mm)
MOUNTING
SURFACE
WATERPROOF
SEALANT
BATH ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON
PUMP/MOTOR END FOR SERVICE.
ACCESS PANELS NOT REQUIRED
FOR BATH TUBS
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

754532-100 Rev. A
7
SPECIFICATIONS:
GENERAL SPECIFICATIONS FOR WHIRLPOOLS AND BATH TUBS
SIDE VIEW DRAIN / OVERFLOW END VIEW
L
H
W
CA
B
J
A 16"
(406mm)
B 13-1/4"
(337mm)
A 15"
(381mm)
B 9-7/8"
(251mm)
A 16-5/8"
(422mm)
B 12"
(305mm)
A 16-1/4"
(413mm)
B 13-1/4"
(337mm)
A 14-1/2"
(368mm)
B 14-1/2"
(368mm)
A 17"
(432mm)
B 11"
(279mm)
A 17"
(432mm)
B 9-1/2"
(241mm)
A 17"
(432mm)
B 13"
(330mm)
A 17"
(432mm)
B 13-3/4"
(349mm)
A 17-3/4"
(451mm)
B 11"
(279mm)
6-3/8"
(162mm)
3"
(76mm)
4"
(102mm)
4"
(102mm)
5-1/4"
(133mm)
5-1/2"
(140mm)
3"
(76mm)
6"
(152mm)
5-5/8"
(130mm)
4"
(102mm)
C 18-1/4"
(464mm)
C 18-1/4"
(464mm)
C 19-1/2"
(495mm)
C 20"
(508mm)
C 21"
(533mm)
C 19-1/2"
(495mm)
C 19-1/4"
(489mm)
C 18-1/4"
(464mm)
C 19-1/2"
(495mm)
C 19-1/4"
(489mm)
Template
Provided
Template
Provided
70-1/2"
(1791mm)
x 46-1/2"
(1181mm)
70"
(1778mm)
x 40-1/4"
(1022mm)
58"
(1473mm)
x 40-1/8"
(1019mm)
Template
Provided
Template
Provided
Template
Provided
Template
Provided
751680-100
70-1/2"
(1791mm)
x 34-1/2"
(876mm)
N/A
As
Desired
72-3/16"
(1833mm)
x 46-1/2"
(1181mm)
71-11/16"
(1821mm)
x 40-1/4"
(1022mm)
59-11/16"
(1517mm)
x 40-1/8"
(1019mm)
As
Desired
As
Desired
As
Desired
N/A
72-3/16"
(1833mm)
x 34-1/2"
(876mm)
L 83-1/2" (2121mm)
W 63-3/4" (1619mm)
H 19-3/4" (502mm)
L 69-1/4" (1759mm)
W 38-1/2" (978mm)
H 19-3/4" (502mm)
L 72" (1829mm)
W 48" (1219mm)
H 21-1/2" (546mm)
L 71-1/2" (1816mm)
W 41-3/4" (1060mm)
H 22" (559mm)
L 59-1/2" (1511mm)
W 41-5/8" (1057mm)
H 23" (584mm)
L 72" (1829mm)
W 35-3/4" (908mm)
H 21-1/2" (546mm)
L 60" (1524mm)
W 42-1/4" (1073mm)
H 21-1/4" (540mm)
L 66" (1676mm)
W 36" (914mm)
H 24-1/4" (616mm)
L 76-3/4" (1949mm)
W 65-3/8" (1661mm)
H 21-1/2" (546mm)
L 72" (1829mm)
W 36" (914mm)
H 21-1/4" (540mm)
94 lb.
(43 kg.)
107 lb.
(49 kg.)
133 lb.
(60 kg.)
115 lb.
(52 kg.)
110 lb.
(50 kg.)
135 lb.
(61 kg.)
107 lb.
(49 kg.)
95 lb.
(43 kg.)
108 lb.
(49 kg.)
101 lb.
(45 kg.)
781 lb. (351 kg)/
37 lb./sq.ft.
(182 kg/sq.m)
640 lb. (291 kg)/
35 lb./sq.ft.
(171 kg/sq.m)
950 lb. (431 kg)/
40 lb./sq.ft.
(196 kg/sq.m)
690 lb. (313 kg)/
33 lb./sq.ft.
(161 kg/sq.m)
611 lb. (277 kg)/
40 lb./sq.ft.
(196 kg/sq.m)
744 lb. (338 kg)/
41 lb./sq.ft.
(200 kg/sq.m)
640 lb. (291 kg)/
35 lb./sq.ft.
(171 kg/sq.m)
659 lb. (299 kg)/
40 lb./sq.ft.
(191 kg/sq.m)
824 lb. (374 kg)/
25 lb./sq.ft.
(117 kg/sq.m)
751 lb. (338 kg)/
42 lb./sq.ft.
(204 kg/sq.m)
80 gal.
(303 l.)
64 gal.
(242 l.)
95 gal.
(359 l.)
69 gal.
(261 l.)
60 gal.
(227 l.)
73 gal.
(276 l.)
64 gal.
(242 l.)
68 gal.
(257 l.)
86 gal.
(352 l.)
78 gal.
(296 l.)
58 gal.
(220 l.)
53 gal.
(200 l.)
74 gal.
(280 l.)
60 gal.
(227 l.)
55 gal.
(208 l.)
44 gal.
(166 l.)
53 gal.
(200 l.)
55 gal.
(208 l.)
71 gal.
(269 l.)
69 gal.
(262 l.)
Description
Drain /
Overflow
Cut Out
Pier
G x F
Rough-In
Recess
E x D
Tub Edge to
Centerline
Overflow: J
Weight with
Water / Floor
Loading
Product
Weight
Gallon to
Overflow
Whirlpool
Operating
Volume
Height to
Underside
of Deck: C
Dimensions
L-W-H
2664
Scala
Corner
2709
Ellisse Oval
6'
2711
Ellisse
6' x 48"
2742
Town Square
6' x 42"
2748
Town Square
5' x 42"
2806
Heritage Oval
6' x 36"
2903
Savona Oval
5' x 42"
2908
Reminiscence
Oval
6060
Cadenza
Corner
7236
Virtuoso
6' x 36"
TABLE 1

8
754532-100 Rev. A
ROUGH-IN REFERENCES
41"
(1041mm)
30-1/2"
(775mm)
21-3/4"
(552mm)
63-3/4"
(1619mm)
42-1/2"
(1080mm)
60"
(1524mm)
8-1/2"
(216mm)
16"
(406mm)
1" (25mm)
INTEGRAL TILE
FLANGE (2) SIDES
3/4"(19mm)
CUTOUT DIMENSION
64-1/4"
(1632mm)
59-1/4" (1505mm)
10" x 10"
(254mm x 254mm)
DRAIN OUTLET
CUTOUT
63-1/2"
(1600mm)
53-3/8"
(1356mm)
OF DRAIN OUTLET
C
L
28-1/2" (724mm)
RECOMMENDED FITTING LOCATION
2-1/2" x 11" (64 x 279mm)
MODEL SERIES 2664
MODEL SERIES 2709
69-1/4"
(1759mm)
OUTLINE OF
CUTOUT
9-7/16"
(240mm)
38-1/2"
(978mm)
19-1/4"
(489mm)
3"
(76mm)
C
LOF DRAIN
OUTLET
12" (305mm) x 9" (229mm)
CUTOUT IN FLOOR FOR DRAIN
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS

754532-100 Rev. A
9
ROUGH-IN REFERENCES
MODEL SERIES 2711
MODEL SERIES 2908
72"
(1829mm)
36-1/2"
(927mm)
OUTLINE OF CUTOUT
70-1/2" X 46-1/2"
(1791 X 1181mm)
C/L OF
DRAIN
4"
(102mm)
12"
(305mm)
48"
(1219mm)
9" x 14"
(229 x 356mm)
FLOOR
CUTOUT
RECOMMENDED
FITTING
LOCATION
2-1/2" X 11"
OPTIONAL
DECK FITTING
AREA
GRAB BAR
FITTING AREA
9" X 12"
(229 x 305mm)
FLOOR
CUTOUT
2-1/2" REF.
(64mm)
66"
(1676mm)
36"
(914mm)
18"
(457mm)
13"
(330mm)
INTEGRAL
FITTING
DECK
6"
(152mm) C/L OF
DRAIN
OUTLET
OVERFLOW OUTLINE OF
CUTOUT
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS

10
754532-100 Rev. A
INTEGRAL
FITTING
DECK
72"
(1829mm)
9" x 13"
(229 x 330mm)
FLOOR CUTOUT
11"
(279mm)
35-3/4"
(908mm)
18"
(457mm)
5-1/2"
(140mm) C/L OF DRAIN
OVERFLOW
OUTLINE
OF CUTOUT
OUTLINE OF
CUTOUT - USE
TEMPLATE
9-1/2"
(241mm)
4-1/4"
(1073mm)
21-1/8"
(537mm)
3"
(76mm)
60"
(1524mm)
C
LOF DRAIN
OUTLET
12" (305mm) X 9"(229mm)
CUTOUT IN FLOOR FOR DRAIN
ROUGH-IN REFERENCES
MODEL SERIES 2806
MODEL SERIES 2903
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS