American Standard Silhouette 7163.001 User manual

G31
© 2008 AS America Inc.
SILHOUETTE™ 33"
SHALLOW DOUBLE BOWL SINK
AMERICAST®
Revised 2/08
SILHOUETTE™ 33" SHALLOW DOUBLE BOWL
KITCHEN SINK
• Americast® brand engineered material
• Dual level double bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available in 1, 3, 4, or 5 faucet hole conguration
• Customized hole punchings available
(see page G56)
Top Mount/Undercounter:
❏ 7163.001 Center hole only
❏ 7163.803 3 hole
❏ 7163.804 4 hole
❏ 7163.805 5 hole
Nominal Dimensions:
838 x 559 x 152mm
(33" x 22" x 6")
Bowl sizes:
Right Hand: 359mm (14-1/8") wide
413mm (16-1/4") front to back
152mm (6") deep
Left Hand: 359mm (14-1/8") wide
476mm (18-3/4") front to back
152mm (6") deep
Undercounter Installation Order:
❏ 791326-100 Mounting Kit (consists of
cut-out template and mounting clips)
* See faucet section for available models
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
Silhouette Shallow Double Bowl
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
•When installed so top of sink is 876mm (34-1/2") from finished floor.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND
ANSI A117.1 ACCESSIBLE AND USEABLE BUILDINGS AND
FACILITIES - CHECK LOCAL CODES.
BARRIER FREE
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Traps:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
❏ Web Cover: 8106.100, Color:
❏ Bottom Sink Rack (Left): 7405.100, Color:
❏ Bottom Sink Rack (Right): 7406.100, Color:

G32
© 2008 AS America Inc.
NOTES:
* COUNTERTOP CUTOUT 527 X 806mm WITH 25mm
(20-3/4 X 31-3/4 WITH 1) RADIUS AT CORNERS.
SUPPLIES NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791326-100 FOR
UNDERCOUNTER FAUCET DECK CUTOUT VARIATIONS.
SUPPLIES NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
7163.804
4 HOLE
7163.805
5 HOLE
7163.001
CHO
C/L
FINISHED WALL
OR SPLASHBACK
1-1/2" O.D.
TAILPIECE
FINISHED FLOOR
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
*CUTOUT NOTE
1/2"
(13mm)
5-3/4"
(146mm)
5-1/2"
(140mm)
16-1/2"
(419mm) 33"
(838mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
RAD. TYP.
7-7/8"
(200mm)
8-5/8"
(219mm)
7-7/8"
(200mm)
10-1/8"
(257mm)
22"
(559mm)
34"
(864mm)
2-1/8"
(54mm)
1-1/2" (38mm)
DIA. HOLES TYP.
4" (102mm) 4"
(102mm)
4"(102mm)
4"(102mm)
2" (51mm)
OPTIONAL
7163.804
4 HOLE
7163.805
5 HOLE
7163.001
CHO
C/L
FINISHED WALL
OR SPLASHBACK
FINISHED FLOOR
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
*CUTOUT NOTE
DETAIL OF MOUNTING CLIP
(KIT No.791002-100)
BRASS
INSERT 3/4"
(19mm)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
2-1/8"
(54mm)
1-1/2" (38mm)
DIA. HOLES TYP.
4" (102mm) 4"
(102mm)
4"(102mm)
4"(102mm)
2" (51mm)
OPTIONAL
16-1/2"
(419mm) 33"
(838mm)
36"
(914mm)
5-3/4"
(146mm)
6"
(152mm)
7-7/8"
(200mm)
10-1/8"
(257mm)
22"
(559mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
RAD. TYP.
7-7/8"
(200mm)
8-5/8"
(219mm)
1-1/2" O.D.
TAILPIECE
SILHOUETTE™ 33"
SHALLOW DOUBLE BOWL SINK
AMERICAST®
Revised 2/08
Undercounter Mount
7163. Series