American Standard 3125.016.020 - 3125.016.020 Yorkville Right Height Pressure-Assisted Elongated Toilet... User manual

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: For proper operation the recommended working pressure is between 25 psi at valve when flushing and 80 psi static.
!
INSTALLATION INSTRUCTIONS
CADET 1.6 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS
- Model 2462.016 Cadet Elongated 15"
- Model 2467.016 Cadet Elongated 16-1/2" High Bowl
YORKVILLE 1.6 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS
- Model 2876.016 Yorkville Elongated 15"
- Model 2878.016 Yorkville Elongated 16-1/2" High Bowl
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
Closet Flange Set (Cadet Toilets) Neoprene or Graphite Felt Gasket (Yorkville Toilets)
1REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
SAVE FOR FUTURE USE
7301312-100
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2009
2-2
3-2
2-1
3-1
DIMENSIONS (Nominal) NOTE: Distance from floor to closet
flange centerline (rough-in) must be 4" (102 mm) with flange
surface flush to 1/16" (16mm) max. beyond finished wall.
DIMENSIONS (Nominal) NOTE: Distance from wall to closet
flange centerline (rough-in) must be 12" (305 mm)
FOR CADET TOILETS: FOR YORKVILLE TOILETS:
FLUSH TO
1/16" (16mm)
EXPOSED
CLOSET
FLANGE
CLOSET
BOLTS
168mm
(6-5/8") PILOT
HOLES
102mm
(4)
346mm
(13-5/8)
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152 mm) apart
and parallel to floor. (Use
putty to hold bolts in place if
necessary.) Brace under
flooring as needed and
drill two mounting pilot
holes as shown.
INSTALL CLOSET BOLTS
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152 mm)
apart and parallel to wall.
INSTALL CLOSET BOLTS
305mm
(12)
CLOSET FLANGE
CLOSET BOLTS
29-3/4"
(752mm)
18-1/2"
(470mm)
20-1/2"
(516mm)
9"
(230mm)
14"
(356mm)
15"
(381mm)
HIGH BOWL
16-1/2"
(419mm)
29-1/4"
(743mm)
HIGH BOWL
30-3/4"
(780mm)
13-5/8"
(346mm)
12"
(305mm)
9"
(226mm)
1/2"
(11mm)
30-1/4"
(768mm)
20-1/2"
(516mm)
18-1/2"
(470mm)
12"
(305mm)
13-3/4"
(347mm)
9-1/2"
(238mm)
14"
(356mm)
6"
(150mm)
9"
(226mm)
1"
(27mm)
15"
(381mm)
HIGH BOWL
16-1/2"
(419mm)
29-1/4"
(742mm)
HIGH BOWL
30-3/4"
(781mm)

con’t. FOR CADET TOILETS:
7301312-100
5-1
INSTALL TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of
washers marked "THIS SIDE UP" must face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
6-1
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height to
size before installing caps.)
c. Smooth off the bead of sealant around base. Remove
excess sealant.
!
CLOSET
BOLT
NUT
WASHER
BOLT CAP
WAX
RING
SEALANT
4-1
Invert toilet on floor
(cushion to prevent
damage), and install
wax ring evenly
around waste flange
(horn), with tapered
end of ring facing
toilet. Apply a thin
bead of sealant
around base flange.
INSTALL
WAX SEAL
5-2
INSTALL TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of
washers marked "THIS SIDE UP" must face up!
6-2
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
push bowl against ring and flange. Alternately tighten nuts
until toilet is firmly anchored.
CAUTION: DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Insert the tapered washers (supplied in the kit) into the
lag bolts (not supplied). Insert bolts through mounting holes
and tighten into pre-drilled floor openings.
c. Install the four bolt caps on tapered washers. (If necessary,
cut wall bolt length to size before installing caps.)
d. Smooth off the bead of sealant around base.
Remove excess sealant.
!
4-2
Install seal evenly
around waste flange
(horn). Apply a thin
bead of sealant
around base flange.
* Note: Wax seal not
recommended for this
application.
INSTALL NEOPRENE OR GRAPHITE FELT SEAL*
con’t. FOR YORKVILLE TOILETS:
NEOPRENE
SEAL
SEALANT
BOLT
HEAD
WASHER
BOLT
CAP
BOLT
CAP
NUT & WASHER
LAG
BOLT
TAPERED
WASHERS
FLANGE FLANGE
BOLTS
CLOSET FLANGE
- 2 -

SPONGE
WASHER
TANK MTG.
BOLTS
NUT
WASHER
78
10
9
INSTALL TANK
a. Install large rubber gasket over threaded
outlet on bottom of tank and lower tank onto bowl
so that tapered end of gasket fits evenly into bowl
water inlet opening, and tank mounting bolts go
through mounting holes. Secure with metal
washers and nuts.
b. With tank parallel to wall, alternately tighten
nuts until tank is snugged down evenly against
bowl surface.
CAUTION: DO NOT OVERTIGHTEN
NUTS MORE THAN REQUIRED
FOR A SNUG FIT!
INSTALL TOILET SEAT
Install toilet seat in accordance
with manufacturer's directions.
!
ADJUSTMENTS
The flushometer tank is designed and
factory-adjusted to provide a
consistent, safe seal depth in the
bowl after each flush. Field refill
adjustment is not required. The refill
has been preset and locked.
REPAIR PARTS LIST
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
Repair parts are determined by toilet tank number which can be found marked inside tank.
PART NO. DESCRIPTION
TOILET
7381047-200
7381049-200
4142-016.XXX
4142.801.XXX
735133-400.XXX
3481.016.XXX
3483.016.XXX
3701.016.XXX
3703.016.XXX
034783-XXX0A
034602-0070A
7381054-100
7381053-100
7381052-100
7301320-100
034783-XXX0A
735133-401.XXX
603111-0030A
TRIP LEVER ASSEMBLY LH
TRIP LEVER ASSEMBLY, WDI PRESSURE ASSIST, RH
TANK
(COMPLETE WITH COUPLING COMPONENTS AND TANK TRIM)
TANK (COMPLETE WITH COUPLING COMPONENTS AND RH TANK TRIM)
TANK COVER
BOWL, ELONGATED 15"
BOWL, ELONGATED 16-1/2"H
BOWL, ELONGATED 15"
BOWL, ELONGATED 16-1/2" (419mm)
BOLT CAP COVER KIT (INCL TWO COVERS/WASHERS)
COUPLING GASKET
LOWER SUPPLY ASSEMBLY
UPPER SUPPLY ASSEMBLY
VALVE CARTRIDGE ASSEMBLY
TANK COUPLING KIT
BOLTS AND CAPS
TANK COVER FOR LOCKING DEVICE
COVER LOCKING DEVICE KIT
CADET
YORKVILLE
7301312-100
- 3 -
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in water
leakage. Water supply tube or
pipe must extend at least 1/2"
inside threaded shank of valve
(does not apply to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral cone
washer. Fluidmaster
cone washer may not
seal completely on
spiral type supply line.
Captive cone
washers already
included. No
additional
washers needed.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER

11 CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth.
Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or
abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Does not flush a. Water supply valve closed. a. Open valve and allow water to fill tank.
b. Supply line blocked. b. Shut off water supply, disconnect supply line, and inspect
all gaskets and washers. Reassemble.
c. Trip lever linkage damaged. c. Check trip lever, linkage, and actuator wire assemblies
for damage.
Poor or sluggish a. Supply valve partly closed. a. Open supply valve fully. Be sure that proper supply tube
flush size is used.
b. Plugged inlet strainer. b. Remove and clean strainer per enclosed instructions
c. Supply pressure too low. c. Normal supply pressure must be at least 25 psi.
d. Partially clogged trapway and/or d. Remove obstruction. Consult a plumber if necessary.
drain pipe and/or vent.
e. Malfunctioning pressure regulator. e. Replace lower supply assembly.
Toilet leaks a. Poor bowl to tank/floor connection. a. Review Step 4 through 7 of installation procedure.
Toilet does not a. Supply pressure too low. a. Normal supply pressure must be at least 25 psi.
shut off
!WARNING
When servicing or replacing components of the flushometer tank system, be sure that the
water supply is shut off and the toilet is flushed to relieve pressure in the flushometer tank.
For service of the Flushometer Tank System, see enclosed literature.
TROUBLESHOOTING GUIDE
NOTE: The presence of a small amount of water in the bottom of the tank is normal. The air inducer is designed to leak for short periods
during each flush cycle as a self-cleaning action. Drippage is drained into the bowl. If used on water system containing excessive sand
and/or debris, a periodic cleanup of inlet strainer is recommended. (See enclosed instructions for strainer cleaning.)
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is defective in
materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase
will be required—save sales receipt.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to insure local code compliance before installation.
This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse,
misuse, accident or other damages; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner
inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or
installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION
MATERIALS, INCLUDING BUT NOT LIMITED TO TILES, MARBLE ETC. American Standard will not be responsible for any other incidental or
consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this
limited warranty. This limited warranty does not cover any liability for consequential or incidental damages, all of which are hereby expressly disclaimed,
or the extension beyond the duration of this limited warranty of any implied limited warranties, including those of merchantability or fitness for an intended
purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties, so this exclusion may not apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which
case this limited warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased,
or that a service request (including a description of the product model and of the defect) be sent to the following address:
7301312-100
- 4 -
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard-us.com
In Canada:
AS Canada ULC
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx