American Standard Tendence 2088 User manual

SINGLE LEVER
LAVATORY FAUCET
Installation
Instructions
M968712 REV. 1.2
2086
Certified to comply with ANSI A112.18.1
TENDENCE
1
For 3-hole (4" centers) installation,
apply Putty to underside of Escutcheon (4)
and place over holes in lavatory sink with tab
towards back.
FAUCET INSTALLATION
Feed faucet tubes through Rubber Ring (2)
and through hole in Escutcheon (4) or mounting
surface. Make sure Rubber Ring (2) is seated in
groove in base of Faucet (1). Escutcheon (4)
is optional on single hole lavatories.
From below, push Mounting Gasket (5) and
Mounting Washer (6) over Stud (3) and secure
with Nut (7), pushing Faucet (1) to back of sink,
so Stud (3) rests against sink hole. Before final
tightening, adjust Faucet (1) and Escutcheon (4)
so that they are centered.
Carefully bend and/or cut supply tubes and
connect left tube to HOT water and right
tube to COLD water supply using appropriate
connectors.
Plumbers' Putty or Caulking
Adjustable Wrench 3/32" Hex Key
Channel Locks
TOOLS REQUIRED
LAVATORY
PUTTY
1
2
3
4
5
7
6
Turn off water at
main supply.
CAUTION
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

M968712 REV. 1.2
TEST FAUCET
3
4
Remove Aerator.
Turn on water supplies and check for leaks.
Operate Handle up and down, and left and right and check
for proper operation.
Flush lines and reinstall Aerator.
ADJUST HOT LIMIT STOP
Turn on valve and allow water supply temperatures to
stabilize. Move HANDLE to full HOT setting. Check
water temperature.
To decrease hot limit temperature setting:
Pull out Plug Button (1), loosen Handle Set Screw (2)
and remove Handle (3) from Cartridge Stem (5). Remove
Cartridge Cover (4).
Lift Setting Insert (6), rotate counterclockwise one notch and replace.
Check water temperature and repeat if necessary. Unit is factory set
at "0" (full HOT water). As the setting number increases, the more cold
water is supplied in the full HOT handle position.
Replace Cartridge Cover (4). Align Handle (3) and tighten Set Screw (2).
Replace Plug Button (1).
CARTRIDGE TOP
HOTTEST
COOLEST
Blend control
setting 0 - setting
insert covers blend
control setting
number 1 - 4
Blend control
setting 4
1
3
4
2
1
3
4
2
TOP
3
4
5
6
1
2
INSTALL POP-UP DRAIN
2
1
2
A
3
4
5
10
11
12
8
GF
D
E
6
7
F
C
9
Push Tail piece (11) down into Trap (C) (threaded end up).
Assemble Pivot Rod (9) as shown in Figure-2B. Notice the
position of the Concave Washer (G).
Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot
Nut (F).
Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side
up) onto Drain Body (10).
Apply a bead of Putty (D) to underside of Flange (2).
Remove one end of Clip (8) from Pivot Rod (9) by squeezing
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
Adjust stopper height by repositioning Extension Rod (7) and
tightening Thumbscrew (6).
Feed Drain Body (10) up through Sink (A) and thread the
Flange (2) fully onto Drain Body (10).
Tighten Locknut (5) firmly using channel locks, keeping the
pivot rod hole pointed towards the back of the sink.
Drop Stopper (1) into Drain Body (10).
Position Extension Rod (7) onto Pop-Up Rod (E) and tighten
Thumbscrew (6).
1-1/4"
FIGURE-2B:
Push Tailpiece Insert (12) into Tailpiece (11) and push
Tailpiece up and thread tightly into Drain Body (10).
0-RING
5
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS: