American Standard 2257 User manual

SAVE FOR FUTURE USE
1
7301115-100 Rev. C
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2010
2
Refer to instructions supplied with wall carrier for proper installation of 4-bolt support
system wall cavity requirements and rough-in information for waste outlet piping.
Closet Carrier Support
Putty Knife
Sealant
Tape Measure
Regular Screwdriver
Adjustable Wrench
Carpenters Level
Flush Valve
RECOMMENDED TOOLS AND MATERIALS
Pictures may not exactly define contour of china
Model 3351, 3352, 3353, 3354, 2257.001, 2633.100, 2634.001
AFWALL FLUSH VALVE
WALL-MOUNTED TOILETS
INSTALLATION INSTRUCTIONS
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR
HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
FIXTURE MOUNTING
Fixture studs should project
1-7/8" (48mm) from face of
finished wall.
Front View
Side View
FINISHED
WALL
1-7/8"
(48mm)
(4) STUDS
When installed,
top of seat is
17" to 19"
(432mm to 483mm)
from the finished
floor.
Meets the American Disabilities Act Guidelines and ANSI A117.1
Requirements for the Physically Challenged
Thank you for selecting American Standard – the benchmark of fine quality for
over 100 years. To ensure thisproduct is installed properly, please read these
instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
FINISHED WALL
470mm
(18-1/2")
C/L OF SEAT POST
HOLES 140 mm
(5-1/2") CENTER
660mm
(26")
73mm
(2-7/8")
133mm
(5-1/4")
191mm
(7-1/2")
292mm
(11-1/2")
(4) 22mm
(7/8")
HOLES
356mm
(14")
C/L OF
OUTLET
121mm
(4-3/4")
FINISHED
FLOOR
32mm
(1-1/4")
1" N.P.T. OR C.W.T. SUPPLY
AS REQUIRED TO FLUSH VALVE
330mm
(13")
19mm
(3/4")
142mm
(5-1/4")
83mm
(3-1/4")
62mm
(2-1/8")
1-1/2" SPUD
C/L
229mm
(9)
FINISHED WALL
470mm
(18-1/2")
C/L OF SEAT POST HOLES
140mm(5-1/2") CENTERS
660mm
(26")
133mm
(5-1/4")
191mm
(7-1/2")
298mm
(11-3/4")
(4) 22mm (7/8")
DIA. HOLES
356mm
(14")
C/L OF
OUTLET
FINISHED
FLOOR
32mm
(1-1/4")
330mm
(13")
(3/4")
19mm
133mm
(5-1/4")
83mm
(3-1/4")
C/L
229mm
(9")
38mm (1-1/2") DIA. HOLE IN WALL
95mm
(3-3/4")
FOR WALLS UP TO 1" IN THICKNESS FOR EACH INCH
ADDITIONAL THICKNESS OF WALL ADD 25mm (1) TO
MEASUREMENT SHOWN
89mm
(3-1/2")
1" C.W.T. OR N.P.T. SUPPLY
AS REQ'D NOT FURNISHED
121mm
(4-3/4")
VACUUM BREAKER
76mm(3") DIA. HOLE IN WALL
FOR 1-1/2" SPUD
254mm
(10")
41mm
(1-5/8")
38mm
(1-1/2")
62mm
(2-1/8")
184mm
(7-1/4")
or
381mm
(15")
or
432mm
(17")
184mm
(7-1/4")
or
381mm
(15")
or
432mm
(17")

Place back-up nuts on both bottom bolts, and
the top left-hand bolt only.
Adjust the two lower back-up nuts so that front
face of nuts is flush with finished wall.
Adjust waste horn to project 5/16" (7mm) from
finished wall.
Using a level, adjust the top left back-up nut so that
it is in the same vertical plane as the lower left back-up
nut. (If wall surface is irregular, the three back-up
nuts must be positioned to allow a minimum 1/16"
gap between fixture and wall surface.)
NOTE: Bearing nuts and washers must be set to take full loading from the fixture allowing
1/16" (2mm) clearance between fixture and wall.
Follow support manufacturer's recommended setting of closet outlet connection.
Place felt or neoprene gasket (wax ring not recommended) on closet outlet.
When the fixture is installed, closet outlet gasket must be compressed sufficiently to
assure a gas and watertight seal.
Install bowl on support using cap nuts and fiber washers with the back-up nuts and washers.
DO NOT APPLY TOP RIGHT FIBER WASHER AND CAP NUT UNTIL OTHER CAP NUTS
HAVE BEEN FIRMLY TIGHTENED USING A WRENCH.
Install top right cap nut with fiber washer and run up hand tight. Wrench tighten approximately
1/4 turn.
Apply sealant to gap between bowl and finished wall. Remove excess sealant.
7301115-100 Rev. C
3
5
4
- 2 -
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
AS Canada ULC
5900 Avebury Ave.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
FINISHED WALL
CLOSET
CARRIER
SYSTEM
(3) NUTS
WASTE
HORN
5/16" (7mm)
LEVEL
FINISHED WALL
1/16" (2mm)
(IRREGULAR
WALL SURFACE)
The following steps require a helper: