American Standard Enfield 2373.401 User manual

Installation
Instructions
.3&7
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
BIDET FITTING
and VACUUM BREAKER
Roughing-in Dimensions
BIDET OUTLINE
IS SYMBOLIC
FINISHED
WALL
1-1/4 O.D. TAILPIECE
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
DOUCHE
SPRAY
2-1/8
DIA.
FINISHED
FLOOR
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
1-1/4
MAX.
1-3/16
DIA.
(C) (H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2"
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
8 TO 12
2-1/4
DIA.
ENFIELD 2373.401
2373.421
Turn off hot and cold water
supplies before beginning.
CAUTION
MOUNTING BIDET FAUCET
Tighten the MOUNTING NUT (1) to secure the
VALVE BODIES (2).
Replace UPPER GASKET (7) and FRICTION RING (10).
Position the side threaded outlet rearward and secure
MOUNTING NUT (9). Thread ESCUTCHEON (5) onto
TRANSFER VALVE (8) until it seats against the
BIDET LEDGE.
Remove MOUNTING NUT (9), FRICTION RING (10)
and UPPER GASKET (7) from TRANSFER VALVE (8)
and insert TRANSFER VALVE (8) into the center
forward hole of BIDET.
3
4
COLD
HOT
BIDET
LEDGE
2
7
8
1
9
10
5
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
thread DECK ADAPTER (4) onto VALVE BODIE (2)
until it locks against the internal stop.
Congratulations on purchasing your American Standard faucet
with EverClean nish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
with EverClean™ Finish
*Wrench
*Supplied with Fitting
Flat Blade Screwdriver
Adjustable Wrench Channel Locks
Phillips Screwdriver
Required Tools
5VCJOH$VUUFS
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these nishes)

1
3
2
.3&7
SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal
underside of SPRAY BODY FLANGE (2) and secure with
NUT (3).
Screw SPRAY CAP (9) onto SPRAY BODY (1).
Screw SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY
BODY (1). Connect other end of HOSE (4) with SEAL
WASHER (6) to side outlet NIPPLE (7) of the TRANSFER
VALVE (8).

Unscrew LIFT ROD NUT (1) from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated into ESCUTCHEON of LIFT ROD GUIDE (2).
Drop LIFT ROD GUIDE (2) into rear hole of bidet and from
below secure with ROD GUIDE NUT (1).
TEE AND HOSE CONNECTION

Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2)
to bottom of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5) and tighten connection
to ADAPTER (2)
Connect HOSE COUPLING NUTS (6) to Hot and Cold
valve bodies and securely tighten.
LIFT ROD GUIDE INSTALLATION
DRAIN INSTALLATION

Assemble O-RING (1), WASHER (2), PIVOT
ROD (3) and NUT (4) to DRAIN BODY (5).
Concave side of cup WASHER (2) is toward
ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
STOPPER
BIDET
PUTTY
CLIP
9
3
1
4
11
6
5
8
72
10
PUTTY
6
2
7
8
1
3
5
4
9
COUPLING
NUT
3
Cold
Hot
Front
1
2
4
5
6
6

.3&7
WATER SUPPLY CONNECTIONS

Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to proper length.
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE
PURCHASED SEPARATELY.
FINISH DRAIN INSTALLATION
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Using metal TAILPIECE (5), make connection to the TRAP (6).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends
together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1)
and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) and
tightening THUMBSCREW (3).
Cold
Hot FERRULE
COUPLING NUT
3
1
2
3
1
17
4
6
5
2
VALVE STEM
11
10
9
7
8
Install HANDLE ADAPTER (8) onto valve stem.
Push DIVERTER KNOB (7) onto HANDLE ADAPTER (8).
Install RING (9) onto DIVERTER KNOB (7) and tighten
with HANDLE SCREW (10).
Press on KNOB CAP (11).
INSTALL HANDLES
DIVERTER KNOB:
1
2
45
6
3
TOP
Figure "A"
SPLINE END DOWN
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. See figure "A". Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSS
HANDE ASSEMBLY (5) by adjusting male teeth on ADAPTER (1) to
female teeth in HANDLE (4, 5).
Thread LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY
(5) onto DECK ADAPTER (6) until snug against mounting surface.
THREAD ON
TO DECK
ADAPTER

.3&7
Operate Lift Rod (3) and fill Bidet with water. Check
that DRAIN STOPPER (4) makes a good seal and
retains water in Bidet. Adjust stopper height by
repositioning Lift Rod (3) and tightening
Thumbscrew (5).
Release DRAIN STOPPER (4) and check all drain
connections for leaks.Tighten if necessary.
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Operate both handles to flush water lines thoroughly.
Turn DIVERTER (6) to rim wash and bidet spray.
1
3
2
2
6
5
4
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean
water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
EverClean™ Finish Care Instructions

SERVICE
TO CLEAN SPRAY
Replace SPRAY (6) and operate handles several times from OFF
to ON position. Do not force, handles turn only 90˚.
SPRAY (6) may accumulate dirt causing distorted and reduced
water flow. Unscrew and remove SPRAY (6) and rinse clean.
6

To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position. Unthread HANDLE BASE (1) from DECK ADAPTER (2).
Pull HANDLE ASSEMBLY off VALVE STEM (3).
Remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90p
and replace. Replace SPRING CLIP (4).
Find correct position of HANDLE ASSEMBLY by adjusting male
teeth on VALVE STEM (3) to female teeth in HANDLE.
Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) until
snug against mounting surface.
2
90p
1
4
3
5
UNTHREAD
HANDLE
ASSEMBLY