American Standard 4" Centerset Lavatory and Bar Sink Faucets 5400... User manual

4" CENTERSET LAVATORY
AND BAR SINK FAUCETS
Installation
Instructions
34063M-B
Printed in Mexico
5400 SERIES
5401 SERIES
5402 SERIES
7400 SERIES
7401 SERIES
7402 SERIES
7490 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
U.S. PATENT N S. 5,819,789; 4,294,289
CENTERSET
W/P P-UP
5401 SERIES
CENTERSET WITH
G SENECK SP UT
7401 SERIES
HERITAGE SERIES
BAR SINK WITH
SWING SP UT
7490 SERIES
HANDLE
SCREW
P P-UP
R D
B DY
CARTRIDGE
SHANK
AERAT R
RUBBER
WASHER
BRASS
WASHER
L CKNUT
C UPLING
NUT
CLIP
THUMBSCREW
ST PPER
DRAIN
FLANGE
GASKET
WASHER
NUT
DRAIN
B DY
EXTENSI N
PIV T
R D
TAILPIECE

Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1999
C
H TLINE F R HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
SERVICE
1
5
3
CARTRIDGE
SCREEN
TAIL
PIECE
TEST INSTALLED FAUCET
4Remove AERAT R.
With handle in FF position, turn on water supplies and check
all connections for leaks.
perate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
perate LIFT R D and check DRAIN for leaks.
Turn handles into FF position and replace AERAT R.
To change direction of handle rotation,
proceed as follows:
Turn valve to FF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP.
Lift ST P WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
AERAT R may accumulate dirt causing distorted and reduced
water flow. Remove AERAT R and rinse clean.
If spout drips, operate handles several times from FF to N
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves FF.
Replace ADAPTER, HANDLE, SCREW,
and INSERT.
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
L CKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY
(Mo els 5402 an 7402 only)
(Mo els 5401 an 7401 only)
PUTTY
FLANGE
DRAIN
PLUG
RUBBER
GASKET
WASHER
L CKNUT
SINK
2
Apply a bead of PUTTY along the edge of the underside of the B DY and insert faucet
SHANKS through holes of SINK.
Turn off hot and cold water supplies before beginning.
CAUTION
Assemble RUBBER and BRASS WASHERS, and L CKNUTS from underside of SINK.
Drop UPPER LIFT R D through hole in B DY (models 5401 & 7401 only), align B DY
as far forward as possible and secure position by tightening L CKNUTS. (Plastic L CKNUTS
Connect the H T water supply to the left SHANK and the C LD water supply to the right
SHANK using sealant, appropriate connectors, and C UPLING NUTS.
Refer to separate "Instruction Sheet" for assembly of handles.
UPPER LIFT R D
SHANK
B DY
PUTTY
SINK
RUBBER WASHER
BRASS WASHER
L CKNUT
C UPLING NUT
H T
C LD
HANDLE SCREW
1/2" .D. SLIP
on model 7490 are tightened by hand.)
34063M-B
INSTALL POP-UP DRAIN ST PPER
Push TAILPIECE down into TRAP (threaded end up).
Thread L CKNUT, WASHER and GASKET onto
DRAIN B DY.
Apply a bead of PUTTY to underside of FLANGE.
Feed DRAIN B DY up through SINK and thread
FLANGE fully onto B DY.
Tighten L CKNUT firmly, keeping the PIV T R D
pointed towards the back of the SINK.
Drop ST PPER into DRAIN B DY.
Pull TAILPIECE up and thread tightly
into DRAIN B DY.
Position EXTENSI N R D onto P P-UP R D and
tighten THUMBSCREW.
Remove one end of CLIP from PIV T R D by
squeezing ends together while sliding.
Insert PIV T R D into second or third hole in
EXTENSI N and reassemble CLIP. (EXTENSI N
may need to be bent.)
Adjust ST PPER height by repositioning EXTENSI N
and tightening THUMBSCREW.
FLANGE
SINK
GASKET
PIV T
R D
DRAIN
B DY
PUTTY
WASHER
L CKNUT
TAILPIECE
TRAP
TAILPIECE CLIP
THUMBSCREW P P-UP R D
CLIP
PIV T
R D EXTENSI N
R D
TRAP
EXTENSI N
R D
SPRING
CLIP
ST P
WASHER
90°