American Standard CORNICE 0611 Maintenance manual

SAVE FOR FUTURE USE
7301997-100 01/20
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2020
NOTE: Pictures may not exactly define contour of china and components.
0611 CORNICE™PEDESTAL SINK
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
!
OBSERVE LOCAL PLUMBING AND BUILDING CODES
Recommended Tools & Materials
Adjustable Wrench
Putty Knife
Channel Lock Pliers
Regular Screwdriver
Phillips Screwdriver Drill Basin Wrench
Plumbers' Putty or
Caulking
Tubing Cutter Tape Measure Pipe Wrench
Hacksaw
Level
ROUGHING-IN DIMENSIONS:
28-3/4"
(730mm)
33-1/8"
(841mm)
5"
(127mm)
17-3/4"
(451mm)
21"
(533mm)
C/L HANGER
OUTLINE OF
PEDESTAL
C/L OUTLET
ROUGH
CENTER OF SLOT
OF HANGER
3/8" (10mm)
COLD WATER
3/8" (10mm)
HOT WATER
C/L OUTLET ROUGH
C/L HANGER
3-1/2"
(89mm)
15-3/4"
(400mm)
11" (279mm)
11"
(279mm)
18-7/8"
(480mm)
7"
(179mm)
5" (127mm)
7-1/4"
(184mm)
22-3/16"
(563mm)
11"
(279mm)
FINISHED FLOOR
4"
(102mm)

27301997-100 01/20
5 6
4
Set the pedestal back in place. Put a 3/4" (19mm)
washer on each of the screw(s), then screw the
screw(s) for the pedestal loosely to the oor.
1
Provide suitable reinforcement behind finished wall for lavatory
mounting screws and brackets (reference FIGURE 1).
The centerline of the cross braces should be 28-3/4" (730mm)
up from the floor on both walls.
3
2Hangers provided with the lavatory should be mounted
11" (279mm) (Center of Slot of Hanger) from the corner
and 28-3/4" (730mm) up from the oor on each wall.
(reference ROUGHING-IN and FIGURE 2) Tighten the
hanger, (center slot only) until they will support the
lavatory leaving “play” for nal adjustment later. Make
sure hanger is in its highest position when snugging
hanger. Set the lavatory in place.
28-3/4" (730mm) 28-3/4" (730mm)
FLOOR
FIGURE 1 28-3/4"
(730mm) 28-3/4"
(730mm)
11"
(279mm) 11"
(279mm)
WALL
WALL
FLOOR
FIGURE 2
FIGURE 3
FLOOR
WALL WALL
(2)-PEDESTAL BASE
ANCHOR SCREWS
NOT SUPPLIED
Position the pedestal leg by using the recess indentation on
the underside of the lavatory as a guide and t to the lavatory
with no gaps. The back side of the leg should be vertical and
away from the wall surface (reference FIGURE 3). Mark the
location of the hole(s) in the bottom of the leg. Remove the
leg, then drill the starter hole(s) as marked. These hole(s)
should be 1-1/2" (38mm) deep. Insert a plastic expansion
shield into each hole(s) if required.
Examine the alignment of the pedestal lavatory to the wall
to be sure it is centered where you want it. Also check the
level and adjust as needed.
Tighten the screw(s) at the base of the pedestal leg.
CAUTION: Do not overtighten, as this may crack the
vitreous china.
Remove the lavatory and slide the hangers
upward to their highest positions. Reset the
lavatory to position the hangers in their nal
position. Remove the lavatory once more and
tighten the hangers rmly into place using
additional screws.

A
9
7
B
C
8
Place the lavatory on a thick layer of papers or drop
cloth to protect it from scratches. Following
manufacturer’s instructions, install faucet and drain
assembly (not included). Be certain to apply a bead of
sealing putty on the underside of the drain (if needed)
(reference area A) in order to ensure a watertight seal
between the lavatory and drain. Remove excess putty
after installing drain on lavatory.
In the United States:
American Standard Brands
1 Centennial Ave.
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
LIXIL Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
37301997-100 01/20
Return the tted lavatory to the installed position. Connect
trap to drain assembly, hand tighten to check alignment. It
may be necessary to cut off part of the tailpiece (area B)
or part of the horizontal leg of the trap (area C).
Secure the lavatory to the wall as shown in illustration.
Install washers and hand tighten nuts or lag bolts. Level
and square lavatory. Connect hot and cold supply lines
to the shut-off valves. Tighten trap joints for watertight
assembly. Turn on supply lines and check for leaks.
FIGURE 3
FLOOR
WALL WALL
(2)-PEDESTAL BASE
ANCHOR SCREWS
NOT SUPPLIED
LAVY ANCHOR
SCREW SUPPLIED
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (“American Standard®”) plumbing product, within one year after its initial purchase, conrms that it is defective in
materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase
will be required – save sales receipt.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to ensure local code compliance before installation.
This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse,
misuse, accident or other damages; if it was not installed in accordance with American Standard’s instructions; or if it has been modied in a manner
inconsistent with the product as shipped by American Standard.
American Standard’s option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or
installation. IN NO EVENT WILL American Standard BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION
MATERIALS, INCLUDING BUT NOT LIMITED TO, TILES, MARBLE, ETC. American Standard will not be responsible for any other incidental or
consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this
limited warranty. This limited warranty does not cover any liability for consequential or incidental damages, all of which are hereby expressly disclaimed,
or the extension beyond the duration of this limited warranty or any implied limited warranties, including those of merchantability or tness for an intended
purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties, so this exclusion may not apply to you.)
This limited warranty gives you specic legal rights.You may have other statutory rights that vary from state to state or from province to province, in which
case this limited warranty does not affect such statutory rights.
ANCHOR SCREWS