American Standard PORTSMOUTH 4285.410 User manual

SINGLE CONTROL
PULL-DOWN BAR FAUCET
4285.410
4285.410F15
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Installation
Instructions
Certified t o comply with ANSI A112.18.1M
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
Plumbers' Putty or CaulkingAdjustable WrenchPhillips Screwdriver
RECOMMENDED TOOLS
Regular Screwdriver
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Turn off water at
main supply.
CAUTION
PORTSMOUTH™
M965455 Rev. 1.2
BA
SINK OR
MOUNTING
SURFACE
4
5
8
7
6
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Make certain the SEAL (9) is properly seated in recess of faucet body. Insert SUPPLY HOSES (2), SPRAY HOSE (7)
and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions
below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9)
is properly seated in recess of RING BASE (10). Insert supply HOSES (2), SPRAY HOSE (7) and SHANK (3) through
mounting hole and seat RING BASE (10) onto sink or mounting surface. Do not use putty.
RING BASE
7
9
10
3
2
7
1
9
PUTTY
SPOUT BASE
2
3
4
5
8
6
7

4
3
5
24"
(610mm) 2
1
2MAKE WATER SUPPLY CONNECTIONS
4
4a
TEST INSTALLED FAUCET
3CONNECT SPRAY HOSE & INSTALL WEIGHTS
Move HANDLE (1) into "off"
position.
With HANDLE (1) in "off" position,
unthread SPRAY (3) from HOSE (2).
Turn on water supplies. Operate handle back to front, in COLD
and HOT positions, to flush water lines
thoroughly.
Replace SPRAY (3) onto HOSE (2).
Push the SPRAY HOSE END (1) into the HOSE CONNECTOR (2)
until it snaps into place.
With hand spray seated in spout, install WEIGHT (3)
onto HOSE (4) 24 inches from the underside of the sink deck
and secure with SCREW (5).
Check connections for leaks.
(See Section 5)
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
1
REMOVE
M965455 Rev. 1.2
3
3
4
2
1
2
COLD
HOT
SPRAY OPERATION
With FAUCET on pull down SPRAY (3). Check for
leaks. Make sure SPRAY (3) fully retracks and is
seated in the SPOUT HOLDER (4).

CHECK CONNECTIONS FOR LEAKS.
Move HANDLE into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
5
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
7
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).
Clean MANIFOLD (7) and CARTRIDGE (6) ports.
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M965455 Rev. 1.2
1
2
4
3
5
6
7

SINGLE CONTROL
PULL-DOWN BAR FAUCET
M965455 Rev. 1.2
MODEL NUMBER
A911836-0070A
SEAL
M964065-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
Replace the YYY with
Appropriate finish code
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2012
HOT LINE FOR HELP
M964396-YYY0A
HANDLE KIT
M964397-0070A
BUTTON AND
SCREW KIT
M907315-YYY0A
ESCUTCHEON CAP
M951483-0070A
CARTRIDGE
M918511-0070A
CARTRIDGE SCREWS
PORTSMOUTH™
M920017-0020A
SPRAY HOSE
M964395-0070A
WEIGHT
M907989-YYYOA
MOUNTING RING KIT
4285.410
4285.410F15
M964178-YYY220A
(2.2 GPM)
SPRAY ASSEMBLY
M964178-YYY150A
(1.5 GPM)
SPRAY ASSEMBLY