American Standard SELECTRONIC 705X.105 User manual

Installation Instructions
Installation Instructions
Certified to comply with ASME A112.18.1
© 2017 American Standard
NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at: [e-mail]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
SELECTRONIC®
Integrated Faucet with
Above-Deck Mixing
705X.105
705X.115
705X.205
705X.215
MODEL NUMBERS
Product No.'s & Options
Specifications
Faucet Installation
Electrical Installation
Start-up / Maintenance
FAQ’s / Troubleshooting
Parts
1
2
2
3-4
5-9
9-10
11
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS
supplied cables, or cutting, splicing or modifying
any components will void the warranty.
M965654 Rev. 2.2 (12/17)

1
705P400
PRODUCT No.s
705X.105
705X.115
PRODUCT No.s
705X.205
705X.215
4
605XTMV1070
3
2
5
6
1
Deck Plate
Mixing Valve
Base Product
2a
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure
that your installation proceeds smoothly--please read these instructions carefully before you begin.
UNPACKING
The illustration below shows the fitting and all loose items after they have been removed from the carton.
Some items may be packaged partially assembled to other items.
1. Installation Instructions
2. Spout Assembly (less mixing)
2a. Spout Assembly (mixing)
3. Mounting Kit
4. 4" Deck plate (optional, must be ordered separately)
5. Mixing Valve (optional, must be ordered separately)
6. Inline Filter(s)
7. Assembly Parts
DO NOT REMOVE
PROTECTIVE
FILM FROM
SENSOR EYE UNTIL
INSTALLATION IS
COMPLETE.
DO NOT REMOVE
PROTECTIVE
FILM FROM
SENSOR EYE UNTIL
INSTALLATION IS
COMPLETE.
Platformwith Universal Sensor•Flexible Selectronic
•Easy installation. All electronics in the spout; nothing below deck
•User adjustable above-deck mixing uses ceramic disc
valve for dependability & long life
•Mixing handle can be removedfo r one time temperature
setting during installation
Installation Instructions
Installation Instructions
Certified to comply with ASME A112.18.1
© 2017American Standard
NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.
Tolearn more about American Standard Selectronic®Products visit our website at:www.americanstandard-us.com
or e-mail us at: [email protected]
For Parts, Service,Warranty or other Assistance,
please call (844) CRT-TEAM/ [phone] (InCanada: 1-800-387-0369)
(InToronto Area only: 1-905-306-1093)
SELECTRONIC®
Integrated Faucet with
Above-Deck Mixing
705X.105
705X.115
705X.205
705X.215
MODEL NUMBERS
Product No.'s & Options
Specifications
Faucet Installation
Electrical Installation
Start-up / Maintenance
FAQ’s / Troubleshooting
Parts
1
2
2
3-4
5-9
9-10
11
CAUTION: Useonly American Standard supplied
transformers and cable sets.Using non-AS
supplied cables, or cutting,splicing or modifying
any components will void the warranty.
M965654 Rev. 2.2 (12/17)
7
6
Plug-In AC
Power Kit
Hard-Wired AC
Power Kit
Multi-AC
Power Kit
PWRX
Power Kit
PK00.PACPK00.WRK PK00.HAC PK00.MAC
POWER KITS SOLD SEPARATELY

SPOUT ASSEMBLY INSTALLATION;
Fig. 1
TOOLS REQUIRED; Fig. 2 Fig. 2
12.5 mm Hex Wrench
(Included)
2Adjustable Wrench
3Plumbers' Putty or Caulking
4Phillips Screwdriver
5Tape Measure
12
34510'
Fig. 1
457mm
(18)
3/8" COMPRESSION
CONNECTORS
CLEARANCE
25mm (min) - 127mm (max)
(1" min - 5" max) 165mm
(6-1/2)
28mm (1-1/8)
66mm
( 2-5/8)
38mm
(1-1/2 )
140mm
(5-1/2)
191mm
(7-1/2)
191mm
(7-1/2)
MOUNTING
SURFACE
FINISHED WALL
OR BACKSPLASH
Roughing-in Dimensions
2
Turn off hot and cold water supplies before beginning
1
Fig. 1
10
6
PUTTY
(If required)
MOUNTING
SURFACE
(OPTIONAL)
TIGHTEN
SPIN NUTS
1. Make sure O-RING (1) is installed in spout base. If installing
ESCUTCHEON (2) (optional): Apply a bead of putty to
bottom edge of ESCUTCHEON PUTTY PLATE (2).
IMPORTANT: Do not use putty when installing faucet
without escutcheon.
2. Insert supply HOSES (3), SHANK (4) and SENSOR CABLE
(5) (if equipped) through hole in ESCUTCHEON with PUTTY
PLATE (2) and mounting surface. (Make sure PIN (6) is in back).
3. Assemble RUBBER WASHER (7), BRASS WASHER (8)
and THREADED LOCKNUT (9) onto SHANK (4) from
underside of sink or mounting surface. Hand tighten
LOCKNUT (9).
4. Use a screwdriver to tighten SCREWS (10) on LOCKNUT
(9). Work your way around LOCKNUT (9), tightening the
screws slightly each time until all are snug to ensure
even pressure.
CAUTION
Note: All plumbing and electrical wiring must be installed
in accordance with applicable codes, regulations and
standards.
RECOMENDED CONTROL BOX OR
EQUIVALENT BY OTHERS
HARD-WIRED AND MULTI AC 10' MAX. CABLE LENGTH
4"(102mm) SQ. X 3-1/2"(89mm) DEEP CONTROL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).
INSTALLATION
2
1
4
3
7
8
9
5
IMPORTANT: Do not
use putty when installing
faucet without escutcheon.
IMPORTANT: Do not
use sealent on threads
CAUTION: Use only American Standard supplied transformers and
cable sets. Using non-AS supplied cables, or cutting, splicing or
modifying any components will void the warranty.
M965654 Rev. 2.2 (12/17)

7
6
5
VERTICAL
C/L
HORIZONTAL
C/L
1
BRACKET INSTALLATION
3
Fig. 1
1
3
2
3
4
4
Important: The 7055 series faucets come with the
standard CR-P2 lithium battery installed in the faucet.
No further action required.
PWRK™VERSION;
1. Connect PWRX BATTERY PACK (1) to SENSOR
CABLE (2).
2. Secure the connections by installing into CONNECTOR
LOCKING DEVICE (3) as shown. Rotate the END CAPS
(4) to secure the connection within the CONNECTOR
LOCKING DEVICE (3).
3. Determine the mounting location of the PWRX
BATTERY PACK (1) by marking center lines as shown.
4. Place the BRACKET (5) on the horizontal center line
and mark the location of the mounting holes to be
drilled.
5. Using 1/4" diameter drill bit, drill two mounting holes
aproximately 1" deep.
6. Install the two ANCHORS (6) provided into the
mounting holes. Use a hammer to lightly tap the
ANCHORS (7) into place and flush with the finished wall.
7. Place the BRACKET (5) over the ANCHORS (6) and
secure with the SCREWS (7) provided.
Do not overtighten.
8. Insert PWRX BATTERY PACK (1) into BRACKET (5).
PWRX 10-Year Battery Pack
Product Page
PWRX Power Kit
(PK00.WRK) 4
Plug-in AC Powe Kit
(PK00.PAC) 5
Hard-Wired AC Prower Kit
(PK00.HAC) 5
MULTI-AC Power Kit
(PK00.MAC) 5
A
ELECTRICAL INSTALLATION
M965654 Rev. 2.2 (12/17)

Important: Turn off power to outlet or electrical box.
FOR PLUG-IN VERSION;
1. Connect PLUG-IN AC POWER SUPPLY (2) to one end
of the SINGLE AC ADAPTER (6).
2. Connect SENSOR CABLE (4) to the other end of the
SINGLE AC ADAPTER (6).
3. Connect PLUG-IN AC POWER SUPPLY (2) to wall outlet.
FOR HARD-WIRED VERSION;
1. Connect 10' EXTENSION CABLE (1) to HARD-WIRED
AC TRANSFORMER (3).
2. Connect SENSOR CABLE (4) to the other end of the
10' EXTENSION CABLE (1).
3. Make Black and White power line connections to
HARD-WIRED AC TRANSFORMER (3) and mount
on ELECTRICAL BOX (5).
Fig. 2
4
Unit #1
(Already Installed)
Fig. 3
Unit #2 Unit #3 Unit #4
1
2
4
3
MAXIMUM OF 15 UNITS PER TRANSFORMER.
10' MAXIMUM CABLE LENGTH BETWEEN UNITS.
MULTI-AC VERSION (DAISY-CHAIN); Fig. 3
Important: Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections.
Note: For Unit #1 electrical instructions, refer to section B (page 3).
For subsequent Units, refer to instructions below...
C
1. Connect one end of the 10' EXTENSION (1) to the available terminal of the previous unit’s Y-ADAPTER (2), and
the other end to the single terminal of the current unit’s Y-ADAPTER (3).
2. Connect SENSOR CABLE (4) to either of the two available terminals of Y-ADAPTER (3).
3. Repeat Steps above for each additional Unit, for a Max. of 15 Units on one AC POWER SUPPLY.
M965654 Rev. 2.2 (12/17)
AC VERSIONS (HARD-WIRED /
PLUG-IN POWER SUPPLY) ; Fig. 2
B
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS
supplied cables, or cutting, splicing or modifying
any components will void the warranty.
Do not connect power to transformer
until installation of faucet is complete.
Recommended Electrical Box or Equivalent
by others 4” (102mm) SQ. X 2-1/2” (64mm)
DEEP 2-GANG ELECTRICAL BOX Appleton
#4SD1 OR EQUAL (BY OTHERS).
BLACK & WHITE
POWER
CONNECTIONS
Fig. 2
6
4
2
3
5
1
1
WALL
OUTLET
4" CONTROL BOX
OR EQUIVALENT BY
OTHERS (6)
BLACK & WHITE
POWER
CONNECTIONS
10' EXTENSION

5
MAKE WATER SUPPLY
CONNECTIONS; Fig. 4
D
INSTALL OPTIONAL MIXING
VALVE; Fig. 5
E
Fig. 5
Note: An optional Thermostatic Mixing Valve may be
installed (sold separately) on faucets 705X.1XX &
705X.2XX in addition to Above Deck Mixing valve.
See setup diagram Fig. 5.
Tee fitting is not supplied with Faucet or
Thermostatic Mixing valve and must be purchased
separately. If faucet inlet hoses will not reach water
supplies, longer hoses must be purchased
separately.
For complete detailed installation and operating
instructions, see installations instructions (No.
M968808) supplied with Thermostatic Mixing Valve.
MAINTENANCE
When the Sensor detects a user, the water immediately
starts to flow. Water flow will stop 1.5 seconds after user is
out of sensor range. This Comfort delay allows the user to
comfortably move their hands without the water turning off.
As a precaution, a Safety Timer will turn off the water,
after the sensor has been blocked for 59 seconds.
The water will stay off until the blockage is removed from
the detection zone.
The Comfort and Safety time settings can be adjusted
using the Optional Remote Control (605XRCT).
HAND WASH SENSOR OPERATION;
Fig. 1
A
DETECTION
ZONE
REMOVE PROTECTIVE FILM FROM SENSOR EYE
WHEN INSTALLATION IS COMPLETE. PROTECTIVE FILM
1. Turn off hot and cold water supplies before
beginning.
2. Place each INLINE FILTER (3) on each wall supply
outlet. Be sure that INLINE FILTER (3) is inserted
in the correct direction. (See Illustration)
3. Connect HOT FLEXIBLE SUPPLY (marked with red
stripe) (1) to INLINE FILTER (3) on hot water control
stop (4). Connect COLD FLEXIBLE SUPPLY
(marked with blue stripe) (2) to INLINE FILTER (3)
on cold water control stop (5). Use adjustable
wrench to tighten connections. Do not over tighten.
4. Faucet supplies are 18" long from faucet base.
Note; If additional supply length is required,
installer must purchase those parts separately.
Important; If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
Fig. 1
Installation Instructions
In sta ll ati on I n st ru cti on s
(In TorontoArea only: 1-905-3061093)
SELECTRONIC™
Thermostatic Mixing Valve
Certifiedto comply with ASME A112.18.1M
© 2005 American Standard
M968808
To learn more aboutAmerican Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: [email protected]
For Parts, Service,Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTETO INSTALLER: Please give this manual to the customer after installation.
(In TorontoArea only: 1-905-3061093)
605XTMV
Specifications
Installation
Adjust Temperature
Service
Replacement Parts
1
2
3
3
4
No. M968808
HOT
SUPPLY
COLD
SUPPLY
TEE
FITTING
Optional Mixing Valve
(Sold Separately)
TEMPERED
WATER SUPPLY
COLD
WATER
M965654 Rev. 2.2 (12/17)
Fig. 4
IMPORTANT: Do not
use sealent on threads
1
2
3
COLD
HOT
(3) INLINE
FILTER 5
4

6
5
Fig. 2
1. Remove the FAUCET SPOUT (1) by unthreading
the LEVER SCREW (2) and pulling off the LEVER
HANDLE (3). Unthread the FAUCET SPOUT
SCREW (4) at the back of the FAUCET. Pull
FAUCET SPOUT (1) up and off. Fig. 2.
2. Disconnect the BLACK POWER SUPPLY
CONNECTOR (1) and reconnect. Fig. 3.
3. While the SENSOR CONTROL LED (2) is blinking
slowly, place your hand 1 - 2 in. (25.4-50.8mm) in
front of the sensor. Fig. 4.
4. When the LED stops blinking and stays "ON", move
your hand to the desired position and hold in place
until the LED begins to blink again. Fig. 4a.
5. Once the SENSOR CONTROL LED (2) begins to
blink again, remove your hand from the detection
zone. When the flashing stops, the detection
distance is set.
6. Replace FAUCET SPOUT (1) and LEVER HANDLE
(3). Install LEVER HANDLE SCREW (2), FAUCET
SPOUT SCREW (4) and tighten. Fig. 2.
Note:The LEVER HANDLE (3) can be removed to
prevent users from adjusting the water temperature.
Replace the LEVER HANDLE (3) with PLUG
BUTTON (5) as shown. Fig. 2.
CHANGE SENSOR RANGE;
(Factory set at 6") Fig. 2, 3, 4, & 4a
B
1
4
3
5
2
REMOVE
REPLACE
Fig. 3
1
Fig. 4 Fig. 4a
UP TO 10"
(254mm)
BLINKING LED
2
BLINKING LED
2
1"-2"
(25.4mm-
50.8mm)
M965654 Rev. 2.2 (12/17)

7
1. Remove the FAUCET SPOUT (1) by unthreading the
LEVER SCREW (2) and pulling off the LEVER
HANDLE (3). Unthread the FAUCET SPOUT
SCREW (4) at the back of the FAUCET. Pull FAUCET
SPOUT (1) up and off. See Fig. 2 in this section.
2. Disconnect both ELECTRICAL CONNECTIONS. Fig. 5.
3. Untighten SENSOR SCREW (1) with a 2.5mm HEX
WRENCH. Remove SENSOR ASSEMBLY (2) from
FAUCET SPOUT (3). Remove O-RING (5). Remove
SENSOR (2a) from CARRIER (4) and replace with
new SENSOR (2a). Replace O-RING (5). Install
SENSOR ASSEMBLY (2) into FAUCET SPOUT (3).
Tighten SENSOR SCREW (1). Fig. 6, 7.
4. Replace FAUCET SPOUT (1) and LEVER HANDLE (3).
Install LEVER HANDLE SCREW (2), FAUCET SPOUT
SCREW (4) and tighten. See Fig. 2 in this section.
REPLACE SENSOR;
Fig. 5, 6 & 7.
C
Fig. 5
DISCONNECT
WIRE CONNECTIONS
1
Fig. 6
2
3
2.5mm HEX
WRENCH
Fig. 7
2a
4
5
M965654 Rev. 2.2 (12/17)

8
1. Remove the FAUCET SPOUT (1) by unthreading the
LEVER SCREW (2) and pulling off the LEVER
HANDLE (3). Unthread the FAUCET SPOUT
SCREW (4) at the back of the FAUCET. Pull FAUCET
SPOUT (1) up and off. See Fig. 2 in this section.
2. Disconnect SENSOR CABLE (1) from SOLENOID
CABLE (2). Fig. 8.
3. Unthread SOLENOID VALVE (2) from VALVE BODY
(3). Fig. 9.
4. Remove FILTER SCREEN (4) from base of SOLENOID
VALVE (2). Clean and replace. Fig. 9.
5. Thread SOLENOID VALVE (2) into VALVE BODY (3)
and hand tighten. Reconnect SENSOR and SOLENOID
CABLES (1). Fig. 8.
6. Replace FAUCET SPOUT (1) and LEVER HANDLE
(3). Install LEVER HANDLE SCREW (2), FAUCET
SPOUT SCREW (4) and tighten. See Fig. 2 in this section.
CLEAN FILTER SCREEN ON
SOLENOID VALVE; Fig. 8 & 9
D
1. Remove the FAUCET SPOUT (1) by unthreading the
LEVER SCREW (2) and pulling off the LEVER
HANDLE (3). Unthread the FAUCET SPOUT
SCREW (4) at the back of the FAUCET. Pull FAUCET
SPOUT (1) up and off. See Fig. 2 in this section.
2. Pull out LIMITER STOP (1) from the VALVE STEM
(2). Unthread COLLAR NUT (3) from VALVE BODY (4).
Fig. 10.
3. Pull DIVERTER CARTRIDGE (5) out and replace
with new DIVERTER CARTRIDGE (5).
NOTE: Make sure the two ALIGMENT PINS (6) in the
base of the DIVERTER CARTRIDGE (5) are facing
upward. Fig. 11.
4. Replace FAUCET SPOUT (1) and LEVER HANDLE
(3). Install LEVER HANDLE SCREW (2), FAUCET
SPOUT SCREW (4) and tighten. See Fig. 2 in this section.
REPLACE DIVERTER CARTRIDGE;
Fig. 10 & 11
E
Fig. 9
42
3
4
2
1
Fig. 10
Fig. 12
9
8
Fig. 8
6
5
Fig. 11
M965654 Rev. 2.2 (12/17)

9
GENERAL CLEANING; Fig. 13
G
1. Remove the FAUCET SPOUT (1) by unthreading the
LEVER SCREW (2) and pulling off the LEVER
HANDLE (3). Unthread the FAUCET SPOUT
SCREW (4) at the back of the FAUCET. Pull FAUCET
SPOUT (1) up and off. See Fig. 2 in this section.
2. Replace LEVER HANDLE and rotate
counter-clockwise to its stop position (100% cold).
Remove HANDLE.
3. Pull out LIMITER STOP (1) from the VALVE STEM (2).
4. Rotate LIMITER STOP (1) 180 degrees and insert
back onto VALVE STEM (2).
5. Replace FAUCET SPOUT (1) and LEVER HANDLE
(3). Install LEVER HANDLE SCREW (2), FAUCET
SPOUT SCREW (4) and tighten. See Fig. 2 in this
section.
CHANGE HOT LIMIT SETTING
FROM 95% TO 85%; Fig. 12
F
3
9
8
1
2
ROTATE 180˚
SLOT
SLOT
Fig. 12
Fig. 13
FAQ'S
Q: How will I know if the battery needs to be replaced?
A: Valve will not open and sensor will continuously blink 2 times interrupted by a pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced significantly?
A: The filter assembly, flow regulator or areator/spray may be clogged. Check and clean. Refer to Start-up/Maintenance,
sections C, D and E.
Q: Why doesn’t the water flow out of faucet when I'm within the sensor detection zone?
A: Battery may need replacement. Check. If sensor continuously blinks 2 times interrupted by pause, replace battery
or call (844) CRT-TEAM / [phone].
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging from 20-80 psi.
CAUTION
1. Only use a damp, soft cloth to clean the spout and
the sensor.
2. For tougher dirt, use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using any abrasives or harsh detergents
or chemicals.
M965654 Rev. 2.2 (12/17)