American Standard Arch Control Kitchen Faucet 4101.301 User manual

M968583
4101.301
HI-FLOW KITCHEN FAUCET
with SIDE SPRAY
Installation
Instructions
Certified to comply with ANSI A112.18.1M
1INSTALL FAUCET WITH DECK ESCUTCHEON
(4101.351)
ARCH
ALIGN SLOT
AND TAB
SLOT
TAB
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Assemble RUBBER WASHER (4a), BRASS WASHER (5a), and threaded LOCKNUT (6a) onto SHANK (10) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6a). Use a screwdriver to tighten SCREWS (8a) on LOCKNUT (6a)
the same as fitting installation above.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the
SCREWS (8) slightly each time until all are snug to ensure even pressure.
Install SPRAY HOLDER: Insert SPRAY HOLDER (11) into ESCUTCHEON (1). From underside of sink or mounting surface
thread LOCKNUT (12) onto SPRAY HOLDER (11) shank and tighten.
Installation with DECK ESCUTCHEON: Apply a light bead of plumbers putty to underside of ESCUTCHEON (1) if mounting
surface is uneven. Place ESCUTCHEON (1) onto sink or mounting surface with large opening to the right as shown. Insert
supply HOSES (2) and SHANK (3) through ESCUTCHEON (1) and mounting surface. Make sure slot in fitting base aligns
with tab on ESCUTCHEON (1). Figure 1.
Install SPOUT ASSEMBLY: Insert SPRAY HOSE (9) and SHANK (10) through ESCUTCHEON (1) and mounting surface.
Make sure slot in spout base aligns with tab on ESCUTCHEON (1). Figure 2.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
RECOMMENDED
TOOLS
Adjustable Wrench Regular Screwdriver Phillips Screwdriver
Turn off water at
main supply.
CAUTION
14a 5a
9
10
6a
8a
7
4101.301
Figure 2
ALIGN SLOT
AND TAB
SLOT
TAB
4
1
2
3
5
6
8
11
12
Figure 1
Channel Locks
4101.301 shown with
optional escutcheon 4101.000P

M968583
1a INSTALL FAUCET WITHOUT ESCUTCHEON PLATE
(4101.115 with soap dish) (4101.350 less soap dish)
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the
SCREWS (9) slightly each time until all are snug to ensure even pressure.
Insert SEAL WASHER (1) into ESCUTCHEON (2). Place ESCUTCHEON (2) onto sink or mounting surface. Insert supply
TUBES (3) and SHANK (4) through ESCUTCHEON (2) and mounting surface.Make sure slot in fitting base aligns with
tab on ESCUTCHEON (2). Figure 1.
HOT
COLD
2MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Push HOSE END (1) with compression fitting onto COPPER TUBE (2) Make sure
HOSE and COPPER TUBE are fully engaged (approx.1/2" engagement). Use adjustable
wrench to tighten connections. Do not over tighten.
Connect FLEXIBLE SUPPLIES (3) directly to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe)
to Hot and right supply to Cold wall supply. Use adjustable wrench to tighten
connections. Do not over tighten.
Faucet supplies are 24-1/2" long from faucet base.
Note: If additional supply length is required, installer must purchase
those parts separately.
Important: If SUPPLY HOSES (3) are too long, loop as illustrated to avoid kinking.
Assemble RUBBER WASHER (5a), BRASS WASHER (6a), and threaded LOCKNUT (7a) onto SHANK (11) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7a). Use a screwdriver to tighten SCREWS (9a) on LOCKNUT (7a)
the same as fitting installation above.
Install SPOUT ASSEMBLY: Insert SEAL WASHER (1a) into ESCUTCHEON (2a). Insert SPOUT HOSE (10) and SHANK (11)
through ESCUTCHEON (2a) and mounting surface. Make sure slot in spout base aligns with tab on ESCUTCHEON (2a).
Figure 2.
Install SPRAY HOLDER: Insert SPRAY HOLDER (11) into ESCUTCHEON (12). Insert SEAL (14) into underside of
ESCUTCHEON (12). From underside of sink or mounting surface thread LOCKNUT (13) onto SPRAY HOLDER (11)
shank and tighten.
ALIGN SLOT
AND TAB SLOT
RED STRIPE
1/2"
ENGAGEMENT
TAB
2a
1a
11
5a 6a
9a
Figure 1 Figure 2
56
7
9
8
ALIGN SLOT
AND TAB
SLOT
TAB
13
2
1
3
2
1
3
4
12
11
14
10
7a

M968583
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE (1) down into "off" position.
Turn on water supplies and check connections
for leaks.
CHECK CONNECTIONS
FOR LEAKS
4
3
4
1
7
3CONNECT SPRAY HOSE AND SPOUT HOSE
Feed HAND SPRAY HOSE (1) through SPRAY HOLDER (2).
Use wrench to tighten COUPLING NUT (3) on SPRAY HOSE (1)
to SIDE SPRAY CONNECTION (4) on fitting.
Make sure SEAL WASHER (5) is installed in COUPLING
NUT (6). Connect threaded end of HOSE (7) to SPOUT HOSE
COUPLING NUT (6) from fitting. Use wrench to tighten.
2
6
5
1

M968583
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
7
5TEST INSTALLED FAUCET
Move HANDLE (1) down into "off" position.
With HANDLE (1) down in "off" position, pull HAND SPRAY (3)
from holder and direct SPRAY END (3) into sink.
Operate handle up and down, in COLD and HOT positions,
to flush water lines thoroughly.
Replace AERATOR (2).
Check HAND SPRAY (3) operation:
With faucet on push BUTTON (4) to activate HAND SPRAY (3).
Release BUTTON (4) to stop spray and return
HAND SPRAY (3) to holder.
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2)
and remove HANDLE (3).
Unthread ESCUTCHEON CAP (4). Unthread three
MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove
CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
Test fitting.
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
Remove AERATOR (2).
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
1
2
3
4
5
6
8
7
6a
2
3
4
1

M968583
MODEL NUMBERS
HI-FLOW KITCHEN FAUCET
with SIDE SPRAY
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
4101.301
ARCH
M962725-YYY0A
ESCUTCHEON KIT
(4101.301)
(4101.301)
M923651-YYY0A
SPRAY HOLDER
M923276-0070A
SUPPLY HOSE
M907610-YYY0A
SPRAY ESCUTCHEON
(4101.301)
M918521-0070A
CARTRIDGE SCREWS
A951470-0070A
CARTRIDGE
M962716-0070A
BUTTON AND
SCREW KIT
M907305-YYY0A
CARTRIDGE COVER
M962715-YYY0A
AERATOR
CHROME
STAINLESS STEEL
002
075
Replace the "YYY" with
appropriate finish code
060467-0070A
MOUNTING KIT
M962722-0070A
SPRAY HOSE
AND SEAL
M962717-YYY0A
HANDLE KIT
M953578-YYY0A
HAND SPRAY AND HOSE
US61812-YYY0A
NUT
M962726-YYY0A
ESCUTCHEON KIT
WITH PUTTY PLATE
(4101.000P)
042850-0070A
DIVERTER