American Standard COLONY SOFT 4175.300 Series User manual

SINGLE CONTROL
KITCHEN PULL-DOWN FAUCET
4175.300 Series
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Installation
Instructions
Certified to comply with ANSI A112.18.1M
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
1
3
7
AB
PUTTY
SPOUT BASE
SEAL
SEAL
SINK OR
MOUNTING
SURFACE
SPOUT BASE
2
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert SUPPLY HOSES (2), SPRAY HOSE (9) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and
mounting surface. Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2), SPRAY
HOSE (9) and SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
RECOMMENDED TOOLS
Regular Screwdriver
4
5
8
9 9
6
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Turn off water at
main supply.
CAUTION
COLONY SOFT
3
7
2
4
5
8
6
M965036 Rev. 1.6

2MAKE WATER SUPPLY CONNECTIONS
4TEST INSTALLED FAUCET
SPRAY OPERATION
3INSTALL WEIGHTS
Move HANDLE (1) into "off"
position.
With HANDLE (1) in "off" position,
unthread SPRAY (3) from HOSE (2).
Turn on water supplies. Operate handle back to front, in COLD
and HOT positions, to flush water lines
thoroughly.
With FAUCET on press TOGGLE BUTTON (4) on SPRAY (3) to
switch from stream to spray.
Press and hold PAUSE BUTTON (5) to temporarily stop flow from
SPRAY (3). Release PAUSE BUTTON (5) to resume flow from
SPRAY (3).
Replace SPRAY (3) onto HOSE (2).
Check connections for leaks.
(See Section 5)
1
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
1
2
18"
STREAM (AERATOR)
SPRAY
REMOVE
3
2
5
3
1
2
COLD
HOT
4
M965036 Rev. 1.6
With HAND SPRAY (1) seated in SPOUT (2), install
WEIGHT (3) onto HOSE (4) 18 inches from the underside
of the sink deck and secure with SCREW (5).
4
3
5

CHECK CONNECTIONS FOR LEAKS.
Move HANDLE down into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
5
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
7
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
1
2
5
6a
6
8
3
4
7
M965036 Rev. 1.6

MODEL NUMBERS
SINGLE CONTROL KITCHEN
PULL-DOWN FAUCET
A911830-0070A
SEAL
M962806-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
CHROME
STAINLESS STEEL
MATTE BLACK
002
075
242
Replace the YYY with
Appropriate finish code
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2010
HOT LINE FOR HELP
A951470-0070A
CARTRIDGE
M918506-0070A
CARTRIDGE SCREWS
M907306-YYY0A
ESCUTCHEON CAP
M962940-YYY0A
HANDLE KIT
M962294-0070A
BUTTON AND
SCREW KIT
M923640-0070A
SPRAY HOLDER
M922367-0070A
SPRAY HOSE
M952249-YYY220A
SPRAY ASSEMBLY
2.2gpm/8.3L/min.
(4175.300)
M952249-YYY150A
SPRAY ASSEMBLY
1.5gpm/5.7L/min.
(4175.300F15)
M965036 Rev. 1.6
4175.300 Series
COLONY SOFT
M964395-0070A
WEIGHT