American Standard Quentin TU440507 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of ne quality for over 140 years.
RECOMMENDED TOOLS
M965936 Rev. 1.0 (12/18)
ROUGHING-IN DIMENSIONS
Quentin™
Pressure Balancing
Bath and Shower Trim Kit
INSTALLATION
INSTRUCTIONS
TU440507
TU440508
Plumbers’ Putty
or Caulking Adjustable Wrench Channel Locks
Phillips Screwdriver
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
Teon Tape Flat Blade Screwdriver
CARTRIDGE INSTALLATION
11
1
2
6
5
3
4
UP
UP
BOTTOM OF TUB
4-13/16" REF.
(121 mm) REF. 1/2" COPPER
9-1/4"
(234 mm)
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' (1651 mm)
AND 80'' (1880 mm)
TOP OF TUB RIM
1-5/8" TO 3"
(41 mm TO 76 mm)
FINISHED WALL
4" (102 mm)
74" FOR HEAD
CLEARANCE
(188 cm)
18" OPTIONAL
(457 mm)
1/2" NPT
(12.7 mm) NPT
216 mm
(8-1/2")
REF.
125 mm
(4-7/8")
REF.
1-1/2" REF.
(38 mm) REF.
2-3/4" MAX. (69 mm)
1-3/4" MIN. (45 mm)
6-3/8"
(163 mm)
7-1/4"
(184 mm)
C
OFF
H
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
• Remove PLASTER GUARD (6)
(Keep it installed for thin wall Installation).
• Remove BONNET NUT (1) by unthreading it
Counter clockwise. Remove test CAP (2).
• Remove PROTECTIVE HOUSING (3) from
CARTRIDGE (4). Install with “UP” text on top.
• Reinstall BONNET NUT (1) onto VALVE BODY (5)
and tighten rmly with 12 Nm or 9 lbs/ft.
NOTE: Specied tightening torque
of BONNET NUT (1) is critical to
assure sealing function.

- 2 - M965936 Rev. 1.0 (12/18)
2
4
• Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)
and tightening SET SCREW (3) from below with 2.5 mm
Hex Wrench supplied.
HANDLE INSTALLATION
3INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
CAUTION Protect nish on SHOWER HEAD
and TUB SPOUT when installing.
4
3
4
3
UP
4
2
UP
1
1
2
UP
1
PLASTER
GUARD
Figure 2.
Figure 1.
Figure 1a.
1
Figure 2a.
C
OFF
H
C
OFF
H
• Remove pipe cap and plug from shower and tub
rough piping.
• Slip TUB SPOUT (1) onto tub nipple and tighten with
4 mm Hex Wrench.
• Apply Teon Tape to both ends of SHOWER ARM (2).
• Install SHOWER ARM (2) with FLANGE (3) into shower
pipe and tighten.
• Thread SHOWER HEAD (4) onto ARM (2) and tighten.
• Push SHOWER ARM FLANGE (3) to wall and tighten SET
SCREW (5) with 5/64" hex wrench.
PIPE
CAP
1
PIPE PLUG
TUB FILLER
NIPPLE
1-1/2" REF.
4MM HEX
WRENCH
SHR.
ELBOW
5
2
3
HEX
WRENCH
TEFLON TAPE
C
1
2.5 MM HEX
WRENCH
3
2
C
H
• Figure 1. Remove plaster guard from valve. Push CAP (1)
over VALVE CARTRIDGE (2) until seated against stop.
• Figure 2. Push ESCUTCHEON (3) onto CAP (1) and attach
to valve body with LONG SCREWS (4).
THIN WALL INSTALLATION
• Figure 1a. Push CAP (1) over VALVE CARTRIDGE (2) until
seated against stop.
• Figure 2a. Push ESCUTCHEON (3) onto CAP (1) and attach
to valve body with LONG SCREWS (4).
STANDARD WALL INSTALLATION

- 3 -
7CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
6
M965936 Rev. 1.0 (12/18)
5
• By restricting HANDLE rotation and limiting the amount of hot water
allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1)
reduces risk of accidental scalding. To set the maximum hot water
temperature of your faucet valve, adjust the setting on the HOT LIMIT
SAFETY STOP (1).
• Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before
making adjustment to HOT LIMIT STOP (1). Pull forward and rotate
counterclockwise one number to limit hot water temperature.
Use NUMBERS (5) on CARTRIDGE (4) on HOT LIMIT STOP (1)
for indication.
ADJUST HOT LIMIT STOP
COLDER
(Larger Numbers)
1 2 3 4 5 6 7 8 9 10
HOTTER
(Smaller Numbers)
1 2 3 4 5 6 7 8 9 10
3
4
1
5
2
VALVE LEAKS WHEN SHUT OFF
• Remove CARTRIDGE, see STEP 1 and STEP 2 and REVERSE process.
• Clean SEALS on the side of CARTRIDGE. Clean inside sealing surface of VALVE BODY.
• Re-assemble CARTRIDGE. Install trim. Turn on water supply and check for leaks.
REPLACING CARTRIDGE
• To remove CARTRIDGE (1), install split WASHER (3) between the ridge on the cartridge and the bonnet nut (only
supplied with replacement cartridge) as shown.
• Proceed to unthread BONNET NUT (2) counter clockwise.
Note: CARTRIDGE (1) should be pulling out while unthreading BONNET NUT (2).
• Upon removal of the old Cartridge, install a new cartridge and secure it with BONNET NUT
(Hand tighten).
BACK TO BACK INSTALLATION
• NOTE: Must purchase specialized back to back cartridge. (Part number M970640-0070A)
• Remove CARTRIDGE (1) as detailed in steps above.
• Install back to back cartridge.
• Remove HANDLE (see step 3 and reverse).
• Remove ESCUTCHEON and CARTRIDGE CAP (see step 1 and reverse).
SERVICE
TO GAIN ACCESS TO VALVE FOR SERVICING CAUTION Turn off hot and cold water
supplies before beginning.
Figure 1.
1
3
2

- 4 -- 4 - M965936 Rev. 1.0 (12/18)
Quentin™
Pressure Balancing
Bath and Shower
Trim Kit
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
MODEL NUMBERS
Replace the “YYY” with
appropriate nish code
POLISHED CHROME 002
BRUSHED NICKEL 295
060351-YYY0A
SHOWER ARM
AND FLANGE
8888094.YYY
DIVERTER SPOUT (SLIP-ON)
M970584-YYY0A
DIAL PLATE
M962255-YYY0A
ESCUTCHEON AND SCREWS
M907050-YYY0A
CARTRIDGE CAP
078016-0020A
ESCUTCHEON SCREWS
M970486-YYY0A
HANDLE KIT
M970410-0070A
CARTRIDGE
M970221-0070A
SCREW KIT
M970457-0070A
HANDLE ADAPTER KIT
C
OFF
H
PURCHASE SEPARATELY
M954805-YYY0A
DEEP ROUGH-IN KIT
PURCHASE SEPARATELY
M970640-0070A
BACK-TO-BACK
CARTRIDGE
TU440507
TU440508