American Standard BERWICK 7430.801 User manual

1
2
5
4
GROOVE
(FAUCET
BASE)
MOUNTING
SURFACE
3
8
Figure A
M968640 REV.1.1
7430.821
7430.801
7431.821
7431.801
Certified to comply with ANSI A112.18.1
Installation
Instructions
SPREAD LAVATORY FAUCET
with Speed Connect™ Drain
Adjustable WrenchScrewdriver Channel Locks
Recommended tools
Tubing Cutter
1INSTALL FAUCET
NOTE: READ STEP #16 BEFORE INSTALLING SPOUT TO CONVERT FROM SWIVEL TO FIXED SPOUT.
Turn off hot and cold water
supplies before beginning.
CAUTION
7430.801
7430.821
7431.801
7431.821
1
BERWICK™/ BOULEVARD™
COLLAR ON
MOUNTING NUT
6
4
Figure B
Seat SEAL (1) into under side of SPOUT BASE (2).
Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN
CABLE ASSEMBLY (8) through the mounting hole of lavatory or
mounting surface. Figure A.
7
5
9
From below, slide DRAIN CABLE ASSEMBLY (8) and FAUCET SUPPLIES (3)
through opening in the SPACER (9) against underside of deck. Figure B.
Note: For thick deck installaitons the SPACER (9) is not required.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
From below, push GASKET (7) and RETAINING WASHER (5) onto
MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),
pulling faucet to front of sink, so SUPPLIES (3) rests against
mounting hole. Before final tightening, make sure collar on
MOUNTING NUT (6) is seated into RETAINING WASHER (5).
Figure B.
Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)
to complete faucet mounting.

2
1
VALVE OUTLET SUPPLY CONNECTION
3
RED BAND
BLUE
BAND
Connect Red Banded Hose to Left
Valve and Blue Banded Hose to
Right Valve.
Attach COUPLING NUTS (1) of
SUPPLY HOSES (2) and tighten
making water tight connection.
Important: Loop SUPPLY HOSES (2)
as illustrated so they do not kink.
COLD
HOT
VALVE INSTALLATION
M968640 REV.1.1
4
MOUNTING
SURFACE
Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).
From under side of mounting surface, install VALVE BODY (13) through valve
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16
of a inch above mounting surface top. Fig. A. Thread DECK ADAPTER (10)
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust
LOCKNUT (11).1
8
10
9
12
11
13
10
9
12
11
Place RUBBER RING (9) into DECK ADAPTER (10).
13
13
5/16'' MIN.
Fig. A.
INSTALL HANDLES
1
2
4a4
5
13
LEVER HANDLE CROSS HANDLE
FLAT BLADE SCREWDRIVER
Push ADAPTER (1) on VALVE STEM (2). Tighten
STEM SCREW (3) with a flat blade to secure ADAPTER (1).
(Figure A)
Find correct position of HANDLE ASSEMBLY (4, 4a) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4, 4a).
Thread HANDLE ASSEMBLY (4, 4a) onto DECK
ADAPTER (5) until snug against mounting surface.
THREAD ON
TO DECK
ADAPTER
2
2
(Figure A)

M968640 REV.1.1
3
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
9
5
7
6
TIGHTEN LOCKNUT
1
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
2
3
3
1
1
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
INSTALL DRAIN FROM
BELOW FIXTURE 8
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
4
Fig. A. Fig. B.
Fig. A. Fig. B.
POP-UP KNOB (1) must be fully down. Fig. B.
FLANGE GASKET AND POP-UP KNOB
WHITE FOAM
GASKET
NOT VISIBLE DRAIN
FLANGE
Fig. A.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
DRAIN
BODY
4
DOWN
1
2
DRAIN
OUTLET
1
3
4
REAR OF SINK

M968640 REV.1.1
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
11
2
MAKE WATER SUPPLY AND WASTE CONNECTIONS
12
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
Fig. A.
ATTACH CABLE CONNECTOR
10
2
1
Fig. B.
1-1/4” O.D.
4
2
1
3
FERRULE
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use
adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply when
bending. Use tubing cutter to cut to proper length.
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
COUPLING
NUT
1

M968640 REV.1.1
5
To change direction of handle
rotation, proceed as follows:
Turn valve to OFF position.
Thread counter-clock wise
HANDLE BASE (1) to remove
HANDLE ASSEMBLY (2) from
ESCUTCHEON BASE (3).
Use a flat blade screw driver
to remove SPRING CLIP (4).
Lift STOP WASHER (5), turn 90˚
and replace.
Replace SPRING CLIP (4).
Reinstall HANDLE ASSEMBLY (2).
If spout drips, operate handles
several times from OFF to ON
position. Do not force - handles
turn only 90˚.
To change from swivel to fixed spout, proceed as follows:
Remove PLUG BUTTON (1) from back of spout. VIEW “A”
Remove SET SCREW (2) using screwdriver.
Install FIXING SET SCREW (3) using Hex Wrench supplied.
Align SPOUT (4) and tighten SET SCREW (3) to secure SPOUT (4).
Replace PLUG BUTTON (1).
SERVICE
CARE INSTRUCTIONS:
90˚
17
15 16
VALVE
13
CHECK DRAIN CONNECTIONS
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3). First loosen aerator set screw with
HEX WRENCH (6) supplied. Pull out AERATOR (3) with
AERATOR KEY (7).
Operate both HANDLES (1) to flush water
lines thoroughly.
Replace AERATOR (3) and tighten set screw.
HOT
COLD
2
4
2
1
“P” TRAP
AERATOR
SET
SCREW
WASTE
OUTLET
3
Operate POP-UP KNOB (5) and fill Sink with water. Check
that DRAIN STOPPER (4) makes a good seal and retains
water in Sink. If STOPPER (4) does not seal properly, please
refer to “Troubleshooting Guide” in these instructions.
Release POP-UP KNOB (5) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
7
6
5
14
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
1
1
1
1
2
5
3
4
2
VIEW "A"
CONVERT TO A FIXED SPOUT IF DESIRED.
SPOUT CAN BE FIXED OR SWIVEL.
3
VIEW "A"
4

M968640 REV.1.1
Speed Connect™ Drain
Troubleshooting Guide
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
CAM
CAM CAP
CABLE ADJUSTMENT PROCEDURE
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig. B.Fig. A.
Fig. F.
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
STOPPER REMOVAL PROCEDURE
2
1
RE-ATTACH
DISCONNECT
Fig. C.
STOPPER
6
REMOVE
CAM
Fig. E.Fig. D.
REMOVE
CAM CAP
DOWN
1

M968640 REV.1.1
STOPPER INSTALLATION PROCEDURE
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Unlocked Mode
LOOP TOWARD
FRONT OF SINK
180˚
LOGO
DRAIN
Fig. H.
Locked Mode
(Vandal Proof)
LOGO
DRAIN
Fig. G.
LOOP TOWARD
REAR OF SINK
7
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM

M918462-0070A
CABLE ADAPTER
M968640 REV.1.1
8
M962831-YYY0A
LEFT LEVER
HANDLE ASSEMBLY
BERWICK™/ BOULEVARD™
SPREAD
LAVATORY FITTING
MODEL NUMBER
M962837-YYY0A
CROSS HANDLE
ASSEMBLY
M962832-YYY0A
RIGHT LEVER
HANDLE ASSEMBLY
M962830-YYY0A
ESCUTCHEON KIT
994053-0070A
CARTRIDGE
918555-0070A
HANDLE SCREW
617852-0070A
HANDLE ADAPTER
M961634-0070A
VALVE
MOUNTING
KIT
024220-0070A
COUPLING NUT
M962818-0070A
AERATOR KIT
A912831-0070A
SPOUT O-RING
M962905-0070A
SPOUT SET
SCREW KIT
© AS America,Inc. 2009
M962492-0070A
MOUNTING KIT
M919660-0020A
6” TAILPIECE
(NOT INCLUDED
WITH FAUCET)
M962552-0070A
CAM ASSEMBLY
M952425-YYY0A
DRAIN ASSEMBLY
A923480-0070A
SPACER
M962544-YYY0A
STOPPER
ASSEMBLY
M962457-YYY0A
FLANGE
ASSEMBLY
M962458-0070A
DRAIN MOUNTING KIT
A919661-0020A
TAILPIECE
M922872-0070A
CAM SEAT INSERT
M913207-0070A
TAILPIECE INSERT
M952430-0070A
CABLE ASSEMBLY
CHROME
SATIN NICKEL
002
295
Replace the "YYY" with
appropriate finish code
M962420-YYY0A
POP-UP ROD
M962817-YYY0A
SPOUT KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
IN MEXICO 01-800-839-1200
7430.801
7430.821
7431.801
7431.821
/