American Standard Monterrey 6403 Series User manual

BOTTOM MOUNT
KITCHEN FAUCETS
Installation
Instructions
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M
M965719 (10/15)
Turn VALVES (1) to off position.
Insert ADAPTOR (7) with larger diameter over the VALVE STEM (4).
Align LEVER (2) or WRIST BLADE HANDLE (3) and install onto VALVE STEM (4).
Insert BLUE INDEX (5) into cold valve (right side) and red INDEX (6) into hot valve (left side).
Insert HANDLE SCREW (6) into HANDLES and tighten with screwdriver.
INSTALL HANDLES
2
Turn off water at
main supply.
CAUTION
Adjustable WrenchScrewdriver Channel Locks
Recommended tools
Tubing Cutter
4
1
3
7
2
5
6
6403 Series
6404 Series
8
3
1
2
1
Push TUBING (7) ends into VALVES (6, 6a) side outlets. Insert VALVES (6, 6a)
into mounting holes from underside of ledge.
Install LOCKNUTS (1, 1a), BRASS WASHERS (2) and RUBBER WASHERS
(3, 3a) onto valve and center shanks.
Place RUBBER RING (8) into ESCUTCHEON (9) and thread onto VALVES (6, 6a)
until snug against internal stop.
Tighten LOCKNUT (1, 1a) to secure VALVES (6, 6a) into position.
Firmly tighten COUPLING NUTS (5).
Install FERRULE (4) into COUPLING NUT (5). Thread onto VALVE (6, 6a) and
loosely tighten COUPLING NUTS (5).
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
Place SPOUT RUBBER RING (10) into SPOUT BASE (11) and thread onto VALVE
SHANK (12) and tighten.
INSTALL VALVE ASSEMBLIES
HOT
COLD
4
6
6a
5
5
4
7
9
8
9
MOUNTING
LEDGE
3
5/16" MIN. MOUNTING SURFACE
9
3
6
8
1
2
10
11
3a
1a

M965719 (10/15)
3INSTALL SPOUT
4
Insert SPOUT (1) into SPOUT BASE (2) and tighten
BONNET NUT (3) onto SPOUT BASE (2).
Turn off water at
main supply.
CAUTION
TO CHANGE SPOUT FROM RIDGID TO
FULL SWIVEL SPOUT: (6403 SERIES)
Unscrew SPOUT NUT (1) and remove SPOUT (2).
Take SPOUT CLIP (3) off SPOUT (2) and remove RUBBER RING (4).
Replace RUBBER RING (4) with seperate PLASTIC RING (5) packed
with faucet.
Install SPOUT CLIP (3) on SPOUT (2).
Reassemble SPOUT (2) to SPOUT BASE (6).
Tighten SPOUT NUT (1).
6
1
3
2
1
4
3
5
6404 Series
(Limited Swivel Spout)
COLD
HOT
2
3
MOUNTING
LEDGE
5INSTALL SPRAY HOLDER
Place SPRAY HOLDER (1) into separate hole of SINK (2) and
assemble NUT (3) onto shank from underside of SINK (2).
Hand tighten NUT (3).
1
2
3
70˚
70˚
C/L

M965719 (10/15)
TEST INSTALLED FAUCET
7
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Turn handles into OFF position and replace AERATOR.
SERVICE
8
CARTRIDGE
SCREEN
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW, and INDEX.
AERATOR may accumulate dirt causing distorted and reduced water flow.
Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow.
To clean, first turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at base of CARTRIDGE.
Replace CARTRIDGE until flange is tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW and INDEX.
SPRING
CLIP
STOP
WASHER
90°
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
6
Feed SPRAY HOSE (1) through SPRAY HOLDER (2) and
attach COUPLING NUT (3) of HOSE (1) to HOSE ADAPTOR (4)
on valve body. Tighten COUPLING NUT (3) firmly.
INSTALL SIDE SPRAY
3
4
1
2