American Standard DXV Percy D35105.104 User manual

- 1 -
INSTALLATION INSTRUCTIONS
S A VE FOR FUTURE U S E
M965530Rev. 1.2
ROUGHING-IN DIMENSIONS:
• For reference
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Percy™ Single Control Lavatory
and Vessel Faucet
Loop Handle Vessel - Model D35105.154
Pixie Handle Vessel - Model D35105.150
Loop Handle Lavatory - Model D35105.104
Pixie Handle Lavatory - Model D35105.100
Adjustable WrenchScrewdriver Channel Locks
NOTE: MOUNTING HOLE
1-1/4" (32mm) D.
MOUNTING
SURFACE
20"
(508mm)
FLEXIBLE
HOSES
9-9/16"
(243mm)
6-3/4"
(171mm)
8-13/16"
(223mm)
3-5/8"
(92mm)
1-1/2"
(38mm) MAX.
2-1/4"
(57mm)
1-1/4" OD
(32mm OD)
4-1/2"
(114mm)
1-13/16"
(46mm) D.
1-11/16"
(43mm) D.
2-7/16"
(63mm) D.
LOOP
HANDLE
PIXIE
HANDLE
14-7/8"
(378mm)
14-1/8"
(359mm)
4-1/4"
(108mm)
3-3/4"
(95mm)
3"
(76mm)
6-3/4"
(171mm)
8-15/16"
(227mm)
2-1/4"
(57mm)
4-1/2"
(114mm)
9-5/8"
(244mm)
SUPPLY CONNECTIONS
ARE 3/8" COMPRESSION
2"
(51mm) MAX.
RECOMMENDED TOOLS AND MATERIALS
Thank you for selecting DXV by American Standard.
To ensure that your installation proceeds smoothly,
please read these instructions carefully
before you begin.
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.

- 2 - M965530 Rev. 1.2
1INSTALL FAUCET Turn off hot and cold water supplies before beginning.
CAUTION
• Seat O-RING SEAL (1) into under side of FAUCET BASE (2).
• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8)through the mounting hole of lavatory
or mounting surface. Fig. A.
• From below, push GASKET (7) and RETAINING WASHER (5) onto MOUNTING STUD (4). Secure Faucet with MOUNTING
NUT (6), pulling faucet to front of sink, so SUPPLIES (3)
on MOUNTING NUT (6)is seated into RETAINING WASHER (5). Fig. B.
• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to complete faucet mounting.
8
2
43
1
GROOVE
(FAUCET BASE)
MOUNTING SURFACE
Fig. A.
COLLAR ON
MOUNTING NUT
6
4
7
5
Fig. B.

- 3 - M965530 Rev. 1.2
Fig. A. Fig. B.
Fig. A. Fig. B.
Fig. A. Fig. B.
• POP-UP KNOB (1) must be fully down. Fig. B.
FLANGE GASKET AND POP-UP KNOB
WHITE FOAM
GASKET
NOT VISIBLE DRAIN
FLANGE
• Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
DOWN
UP
1
• Thread LOCKNUT (1) counter-clockwise and
remove from drain body. Remove PLASTIC
WASHER (2) and pull off RUBBER CONE
WASHER (3) Fig. A.
INSTALL POP-UP DRAIN
• Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
TIGHTEN LOCKNUT
REMOVE MOUNTING WASHERS
AND LOCKNUT
• Remove CLEAR PLASTIC COVER (1). Fig. A.
• Remove FOAM SPACER (2) from under
DRAIN POP-UP (3). Fig. A.
2
3
1
ATTACH DRAIN FROM
BELOW FIXTURE
• From under side of SINK
install RUBBER CONE
WASHER (3), PLASTIC
WASHER (2) and
LOCKNUT (1) onto
DRAIN BODY (4).
Note: The CABLE
ATTACHMENT POINT (5)
must face towards the
rear of the SINK.
DRAIN
BODY
4
REAR OF
SINK
4
56
SINK
DRAIN
HOLE
1
3
2
• Drop DRAIN BODY (4) through sink drain
hole. Make sure WHITE FOAM GASKET (5)
(4). Fig.B.
Note: No plumber’s putty or caulk is required.
• The CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK. Fig.B.
1
5
3
2
4
• Tighten LOCKNUT (1)
Wrench or Channel Locks.
1
2
6
4 5
3

- 4 - M965530 Rev. 1.2
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
• Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is
1-1/4" (32mm) O.D. Fig. B.
ATTACH CABLE CONNECTOR
1-1/4" O.D.
(32mm)
• Operate LIFT KNOB (1) to verify that STOPPER (2)
opens and closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
1
APPROX.
20" (508mm)
2
COLD
HOT
3/8" COMPRESSION
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
SUPPLY HOSE (1) (Marked with a Red Band) to the Hot wall valve
and SUPPLY HOSE (2) (Marked with a Blue Band) to the
Cold wall valve.
• Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
• Connect 1-1/4" (32mm) O.D. tailpiece on POP-UP DRAIN
to waste outlet.
1
Fig. A. Fig. B.
1
2
2
1
7
8
9

- 5 - M965530 Rev. 1.2
TEST INSTALLED FITTING
• With HANDLE (1) in OFF position, remove AERATOR (3). Turn on WATER SUPPLIES (2) and check all connections for leaks.
• Operate HANDLE (1) (3).
CHECK DRAIN CONNECTIONS
• Operate POP-UP KNOB (4) (5) makes a good seal and retains water
in Sink. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
• Release POP-UP KNOB (4) down and check all drain connections and "P" trap for leaks. Tighten if necessary.
3
1OFF
ON
COLD
HOT
5
“P” TRAP
WASTE
OUTLET
2
2
4
10

- 6 -
REMOVE
CAM
Fig. E.Fig. D.
REMOVE
CAM CAP
Speed Connect®Drain
Troubleshooting Guide
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
• Fig. D.
• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
• The Stopper can now be removed by lifting it out of the Drain. Fig. F.
CAM
CAM CAP
CABLE ADJUSTMENT PROCEDURE
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig. B.Fig. A.
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stoppershould be in the UP position. Fig. B, C.
• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
• Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
STOPPER REMOVAL PROCEDURE
2
1
RE-ATTACH
DISCONNECT
Fig. F.
Fig. C. DOWN
1
M965530 Rev. 1.2

- 7 -
STOPPER INSTALLATION PROCEDURE
Locked Mode:
• Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
• To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink. Rotate Stopper slightly if necessary so that the Stopper slides
all the way down.Fig. G.
• Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
• Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
• To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink. Rotate Stopper slightly if necessary so that the Stopper slides
all the way down. Fig. H.
• Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed)
or “Unlock” Mode (Stopper is removable).
Unlocked Mode
Locked Mode
(Vandal Proof)
LOOP TOWARD
REAR OF SINK
LOOP TOWARD
FRONT OF SINK
DRAIN
DRAIN
Fig. H.
Fig. G.
M965530 Rev. 1.2
2

- 8 -
LOOP TOWARD
FRONT OF SINK
180˚
DRAIN
Fig. H.
DRAIN
Fig. G.
M965530 Rev. 1.2
Single Control Lavatory
and Vessel Faucet
Percy™
100
144
Replace the "YYY" or "XXX" with
POLISHED CHROME
BRUSHED NICKEL
MODEL NUMBERS
D35105.104
Loop Handle
D35105.100
Pixie Handle
D35105.154
Loop Handle
Vessel
Lavatory
D35105.150
Pixie Handle
Lavatory
Faucet
M964631-YYY0A
LOOP HANDLE KIT
(D35105104, D35105154)
M964633-0070A
CARTRIDGE KIT
M964634-0070A
MANIFOLD SEAL KIT
M964712-0070A
O-RING SEAL
874214.XXX
DRAIN ASSEMBLY
M964636-0070A
AERATOR KIT
M964635-YYY0A
LIFT KNOB & ROD
(LAVATORY)
M964637-YYY0A
LIFT KNOB & ROD
(VESSEL)
M952430-0070A
SPPED CONNECT®
ASSEMBLY
M964638-0070A
MOUNTING KIT
M964632-YYY0A
PIXIE HANDLE KIT
(D35105100, D35105150)
Vessel
Faucet