American Standard COLONY PRO 7074.300 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2020
Thank you for selecting American Standard...
the benchmark of ne quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965767 Rev. 1.2 (1/20)
COLONY®PRO
Single Control Kitchen Faucet
With Pull Down Spray
INSTALLATION
INSTRUCTIONS
7074.300
Certied to comply with ANSI A112.18.1M
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON CAUTION Turn off water at
main supply
3
4
5
8
6
7
SINK OR
MOUNTING
SURFACE
7
7
9
PUTTY
SPOUT BASE SPOUT BASE
2
3
4
5
8
6
7
9
3
2
A (OPTIONAL) B
1
• (A) Installation with ESCUTCHEON (1). (Escutcheon is not supplied with base product). Apply a bead of putty to bottom
edge of ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9) is properly seated in recess of faucet body. Insert
SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting
surface. Follow mounting instructions below to secure faucet to mounting surface.
• (B) Installation less ESCUTCHEON (1). Make certain the SEAL (9) is properly seated in recess of spout base. Insert supply
HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting hole and seat spout base onto sink or mounting surface.
Do not use putty.
• Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
• Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside of sink
or mounting surface. Hand tighten LOCKNUT (6).
• Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws
slightly each time until all are snug to ensure even pressure.
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver

- 2 -
2
M965767 Rev. 1.2 (1/20)
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*Faucet supplies are 21"long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
3CONNECT SPRAY HOSE & INSTALL WEIGHT
4CHECK CONNECTIONS FOR LEAKS
• Move HANDLE into “off” position.
• Turn on water supplies and check
connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
• Thread the SPRAY HOSE END (2) into the HOSE CONNECTOR (1).
• With HAND SPRAY (3) seated in SPOUT (4), install WEIGHT (6)
onto HOSE (5) 21 inches from the underside of the sink deck
and secure with LATCH (7).
• With one weight, spray will retract and dock potentially
requiring slight assistance.
76
1
2
3
4
21"
(610 mm)
5

- 3 -
6
7
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
5
M965767 Rev. 1.2 (1/20)
SPRAY OPERATION
• With FAUCET on press TOGGLE
BUTTON (4) on SPRAY (3) to
switch from stream to spray.
• Press and hold PAUSE BUTTON (5)
to temporarily stop ow from
SPRAY (3). Release PAUSE
BUTTON (5) to resume ow
fromSPRAY (3).
SERVICE
If faucet drips, operate HANDLE several times
from “off” to “on.” Do not apply excessive force.
Clogged CARTRIDGE outlets or inlets may
cause reduced ow.
To clean, rst turn off water supply then:
• Loosen HANDLE SCREW (1) and
remove HANDLE (2).
• Unthread the ESCUTCHEON CAP (3).
Unthread three MOUNTING SCREWS (4).
• Lift CARTRIDGE (5) off MANIFOLD (6).
• Clean MANIFOLD (6) and
CARTRIDGE (5) ports.
• Place CARTRIDGE (5) onto
MANIFOLD (6) and
tighten MOUNTING SCREWS (4)
alternately.
• Replace SNAP RING (3), HANDLE (2),
tighten HANDLE SCREW (1).
For Reduced Flow:
• FLOW CONTROL DEVICE may accumulate
dirt causing distorted and reduced water ow.
To service FLOW CONTROL DEVICE unthread
SPRAY ASSEMBLY and rinse clean FLOW
CONTROL DEVICE.
TEST INSTALLED FAUCET
• Move HANDLE (1) into “off” position.
• With HANDLE (1) in “off” position, unthread
SPRAY (3) from HOSE (2).
• Operate handle back to front, in COLD
and HOT positions, to ush water lines
thoroughly.
• Replace SPRAY (3) onto HOSE (2).
STREAM
(AERATOR)
SPRAY
5
3
4
1
3
2
REMOVE
COLD ON
OFF HOT
1
2
3
4
5
6

- 4 - M965767 Rev. 1.2 (1/20)
Replace the “YYY” with
appropriate nish code
POLISHED CHROME 002
STAINLESS STEEL 075
MODEL NUMBER
7074.300
COLONY®PRO
Single Control Kitchen
Faucet With Pull
Down Spray
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M951483-0070A
CARTRIDGE
M923649-0070A
SPRAY HOLDER
M970196-YYY0A
HANDLE KIT
M918511 -0070A
CARTRIDGE
SCREWS M964397 -0070A
BUTTON & SCREW KIT
(HOT/COLD)
M962806-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
A911836-0070A
SEAL
M907315-YYY0A
ESCUTCHEON CAP
M970705-0070A
WEIGHT
M964766-0020A
SPRAY HOSE
(BEFORE MAY 2020)
M922367-YYY150A
SPRAY HOSE
(AFTER MAY 2020)
M952249-YYY150A
SPRAY HEAD