American Standard Swan 6011 User manual

IN WALL PRESSURE BALANCING
BATH AND SHOWER SETS
To assure proper positioning in relation to wall,
note roughing-in dimensions.
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these
instructions carefully before you begin.
ROUGHING-IN DIMENSIONS
Certified to comply with ANSI A112.18.1
Installation
Instructions
SWAN
6011
6012
THREADED INLETS (STOPS)
INLETS
1/2" NPT
5-7/8"
INLETS 1/2" NPT OUTLETS
1/2" NPT
OUTLETS
1/2" NPT
3-3/8"
3-3/8"
3-3/8"
THREADED INLETS
Required Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
1ROUGHING-IN Turn off water at main supply.
CAUTION
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering,
flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread
sealant or Teflon tape on threaded connections.
NOTE
If the valve is installed on a fiberglass
or other thin wall application, the
PLASTER GUARD (4) can be used as a support.
Connect hot and cold water supplies.
Cap off shower pipe (5) and tub filler pipe (6).
For support, use pipe BRACES (7) secured to wooden braces.
With valve turned off, turn on water supplies. Check for leaks.
COLD
HOT
Cut a 4" dia. hole in the shower stall.
Drill two additional 1" holes to allow access
to the stops.
Remove PLASTER GUARD (4), rotate 90˚
so that indicated screw holes fit MANIFOLD (2).
Push CAP on valve, place ESCUTCHEON on and
attach with screws.
1
7
5
3
6
4
2
See Roughing-in diagram before starting.
Connections are:
1/2" female NPT for threaded inlets
Connect RISER PIPE (1) to MANIFOLD (2)
top outlet marked "SHR".
Connect TUB FILLER PIPE (3) at bottom
outlet marked "TUB".
For proper positioning the finished wall
must be within side wall of PLASTER
GUARD (4).
FINISHED WALL
4"
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
18" OPTIONAL
5" REF.
1/2" NPT
1-5/8"
to
3-1/4"
7-1/8"
1-1/2"
MIN.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 80''
TOP OF TUB RIM
4" REF.
5-1/2" REF.
M968462S-O
1/2" COPPER
SLIP-ON
SPOUT
Tubing Cutter

3INSTALL HANDLE
ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP (1) reduces risk of accidental scalding. To set the maximum
hot water temperature of your faucet, all you need to do
is adjust the setting on the HOT LIMIT SAFETY STOP (1).
1
5
1
3
1
1
9
7
5
3
1
0
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
4
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
Turn CARTRIDGE STEM (2) to the OFF position (coldest setting)
before making adjustment to HOT LIMIT STOP (1). Use a
flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1).
Pull forward and rotate counterclockwise one number to limit hot
water temperature. Use ARROW (3) on CARTRIDGE (4) and
NUMBERS (5) on HOT LIMIT STOP (1) for indication. 1
5
1
5
4
4
3
3
2
2
Push ADAPTER (3) onto VALVE STEM (4).
Install SCREW (2) through ADAPTER (3) into
VALVE STEM (4).
Find correct position of HANDLE (1) and push
HANDLE (1) onto ADAPTER (3).
Install SET SCREW (5) with (2.5mm) HEX
WRENCH (6) provided.
Check proper operation of HANDLE (1).
Turn on water supply and test installed fitting.
Operate valve and diverter spout.
A
2INSTALL TRIM
6
7
3
1
4
5
2
98
CAUTION: Protect finish on SHOWER ARM,
SHOWER HEAD and TUB SPOUT when installing.
SHOWER ARM
FLANGE
SPOUT FLANGE
3
1
5
6
4
M968462S-O
2
When finished tiling the wall, remove PLASTER GUARD (A)
and turn off water supply.
Push CAP (1) over VALVE CARTRIDGE (2).
Mount ESCUTCHEON (3) and gasket to valve body with SCREWS (4).
Remove PIPE CAP (5) from shower pipe. Use sealent on both
ends of SHOWER ARM (6) and thread long end into shower
elbow. Thread SHOWER HEAD (7) to SHOWER ARM (6).
Remove PIPE CAP (9). Use tubing cutter to cut tub filler
pipe a minium of 1-1/2" from finished wall. Install SLIP-ON
SPOUT (8) with flange flush against finished wall and tighten
with a 4mm (5/32") hex wrench.
1-1/2"
MIN.
4mm (5/32") HEX WRENCH

5
Remove handle SET SCREW, remove HANDLE, unscrew HANDLE SCREW and remove ADAPTER.
Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON.
Remove COVER by pulling straight out.
Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve.
TO GAIN ACCESS TO VALVE FOR SERVICING
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove
CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8).
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.
Turn on water supply and see above for installing TRIM and HANDLE.
VALVE LEAKS WHEN SHUT OFF
BACK TO BACK INSTALLATION
BACK TO BACK INSTALLATION
ROTATE 180˚
Remove PRESSURE BALANCE UNIT (5).
Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the
large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should
butt up against top of casting.
Reassemble FIXATION RING (4) and CARTRIDGE (1).
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
1
2
9
5
5
7
8
6
4
3INLETS
LARGE OUTLET
6
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
M968462S-O

A954440-0070A
CARTRIDGE
023603-0070A
CARTRIDGE SCREWS
A923611-0070A
HOT LIMIT STOP
M961854-0070A
FIXATION RING WITH SCREWS
M952100-0070A
PRESSURE BALANCING UNIT
M962304-YYY0A
SHOWER ARM AND
ESCUTCHEON
M907053-YYY0A
CARTRIDGE CAP
078016-YYY0A
ESCUTCHEON SCREWS
M962305-YYY0A
ESCUTCHEON KIT
WITH SCREWS
M962306-YYY0A
LEVER HANDLE KIT
1
5
1
3
1
1
9
7
5
3
1
MODEL NUMBER
027816-0070A
1/2" NPT PLUG
CHROME
SATIN
002
295
Replace the "YYY" with
appropriate finish code
SWAN
PRESSURE BALANCING
BATH AND SHOWER SETS
M909732-YYY0A
SPOUT ESCUTCHEON
M950230-YYY0A
DIVERTER SPOUT
6011
6012
M953530-YYY0A
SHOWER HEAD
M968462S-O
A918657-0070A
ADAPTER SCREW
M918455-0070A
ADAPTER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
IN MEXICO 01-800-839-12-00