American Standard Edgemere 204AA Series Maintenance manual

SAVE FOR FUTURE USE
7302406-100
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Edgemere®2-piece Toilet
Elongated and Round Front
Models 204AA, 204BA Series
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!NOTE: Pictures may not exactly define contour of china and components.
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.To ensure this product is installed properly, please read
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
Wax Ring
Tank To Bowl Gasket
Slow CloseToilet Seat
Water Supply Line
Attachment Handle
with 2 Nuts
2 Plastic Washers
Bolt Caps (2) Bowl-To-Floor
Knobs (2)
T-Bolts with
Retainer (2)
EZ-INSTALL KIT INCLUDED WITH TANK
TANK 4519A and 4519B
BOWL 3519A ELONGATED / BOWL 3519B ROUND FRONT
SOLD SEPARATELY
EZ-INSTALL KIT INCLUDED WITH BOWL

7302406-100
- 2 -
BACK-TO-BACK INSTALLATION
Recommended fitting type for
back-to-back installations.
Depending upon your plumbing and venting conditions, the flow from the toilet in a back-to-back
installation may create a vacuum on the system and draw water from the opposing bowl. The
National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over
is possible. The code does approve a directional "Y" style fitting with proper venting to direct the
water downward and away from the other toilet.
Press firmly.
NOTE: 1/4" EZ-BOLTS INCLUDED.
IF 5/16" BOLTS ARE REQUIRED,
PURCHASE SEPARATELY.
Wax Ring
(sold separately)
1 2
Turn Off Water Supply Flush to remove
water from tank;
sponge remaining
water from
bowl before
removing toilet.
Clean Flange
Before You Start: If Removing An Existing Toilet
!Caution: If leaving floor flange
open for more than 1-2 hours,
cover flange to prevent escaping
sewer gases.
3 4
Apply weight evenly.
Do not move after
placement. Water
tight seal may break. Hand tighten
only. Do not
overtighten.
!

7302406-100
- 3 -
5
7
6
!WARNING: Overtightening of water supply
line nuts could result in breakage and
potential flooding. If the connection leaks
after hand tightening, replace the supply line.
Do not use any type of sealant on the water
supply connection. Use of plumber’s putty,
pipe dope, or any other type of sealant will
void the warranty.
Connect water
supply line.
(Sold separately)
Hand tighten nut.
A
NOTE: To ease installation,
push down on the top of the
tank while tightening handles.
Tighten handles alternately
until the tank contacts the front
and back of the bowl achieving
china-to-china contact.
B
Turn on water supply.
8
Adjust water level to level
indicated on tank by turning
water level adjustment knob
to move float cup up or down.
WATER LEVEL
ADJUSTMENT KNOB
TRIP LEVER
ROD
FLUSH
VALVE
FLAPPER
WATER SUPPLY LINE
TANK TO BOWL GASKET
APPROXIMATE
WATER LEVEL
FLUSH
VALVE
CHAIN
FILL VALVE
OR WATER
CONTROL
FLOAT CUP
REFILL
TUBE
OVERFLOW
TUBE
FLAPPER
SEAL
!Tank to Bowl Gasket
Place the tank gasket over
the tank nut ensuring there
are no gaps between the
gasket and the chinaware.
Install tank bolts in
bottom of tank as shown.
SINGLE FLUSH

7302406-100
- 4 -
9
FLUSH BUTTONS ON TANK
Pressing both buttons at once will flush the low flush amount of 1.0 gal/flush or 3.8 L/flush. The Lite Flush Button (with 3 dots)
should line up over the blue actuator on the flush tower in the tank. The Full Flush Button (with 9 dots) should line up over the
white actuator on the flush tower in the tank.
WATER LEVEL
ADJUSTMENT KNOB
FLUSH
VALVE
LITE FLUSH
ADJUSTMENT
FULL FLUSH
ADJUSTMENT
BAYONET RELEASE
PUSH BUTTON
SILICONE SEAL
REFILL TUBE
WATER SUPPLY LINE
FILL
VALVE
Lite Flush Button (with 3 dots) for liquid waste.
1.0 gal/flush
3.8 L/flush
Full Flush Button (with 9 dots) for solid waste.
1.6 gal/flush
6 L/flush
TIPS:
If the bowl still does not flush properly after following the steps outlined in the troubleshooting guide, remove the tank lid and push one
of the flush buttons on top of the flush valve in the tank. If the flush appears to be normal, you will need to adjust the length of the
threaded rods for the push buttons mounted on the tank lid with the settings as follows:
1. Turn the lid upside down.
2. Loosen the black plastic lock nut.
3. Adjust the white threaded rod one turn counterclockwise.
4. Re-tighten the black plastic lock nut.
5. Put lid back on tank and test the flush. If it is still not flushing properly, repeat steps 1 through 4 until the problem is resolved.
6. If one counterclockwise turn is too much and causes the flush valve to stay open, adjust 1/2 turn clockwise and return to step 4.
FILL VALVE OR
WATER CONTROL
FLOAT
CUP
B
SET WATER
LEVEL HERE
WHITE
THREADED ROD
BLACK PLASTIC
LOCK NUT
BLACK PLASTIC
LOCK NUT
BLUE
THREADED ROD
ADJUSTMENTS
a. Adjust water level. Water level should be
adjusted to level indicated on tank by adjusting
float cup using water level adjustment knob.
b. Flush Valve Setting Adjustments:
Without
Liner
Tank
Full Flush
Adjustment
Lite Flush
Adjustment
2
2.5
Flush Valve
Setting
Adjustments
NOTE: All other settings will result in either more
or less water and are not recommended.
• To remove Flush Valve, apply slight
downward pressure and twist it until the
flush valve disengages from the bayonet.
• To reinstall Flush Valve, reverse the
above procedure.
DUAL FLUSH

7302406-100
- 5 -
In the United States:
American Standard Brands
1 Centennial Ave
Piscataway, New Jersey 08854
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
!
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth.
Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or
abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. These products can seriously corrode fittings in the tank. This damage can
cause leakage and property damage. American Standard shall not be responsible or liable for any damage
caused by the use of in-tank cleaners.
CARE AND CLEANING
Does not
flush
Poor or
sluggish
flush
Toilet leaks
Toilet does
not shut off
Toilet bowl
rocks after
installation
a. Water supply valve closed.
b. Supply line blocked.
*c.Flush valve chain too loose or disconnected.
**c. Push button requires adjustment.
d. Sand or debris lodged in water control.
a. Bowl water level too low.
b. Supply valve partly closed.
c. Partially clogged trapway and/or drain pipe
and/or vent.
d. Supply pressure too low.
a. Poor supply line connection.
b. Poor bowl to tank/floor connection.
a. Flapper/Flush Valve seal leaking or deformed.
b. Sand or debris lodged in water control.
*c. Flush valve chain too tight, holding flapper open.
a. Wax ring not fully compressed.
b. Floor not level.
a. Open valve and allow water to fill tank.
b. Shut off water supply, disconnect supply line and inspect all gaskets
and washers. Reassemble.
*c. Readjust chain length as required.
**c. Adjust rods per step 9
d. Shut off water supply. Remove cap and clean as per Fluidmaster
maintenance instructions at:
www.americanstandard-us.com/enews/fluidmasterguide.pdf
a. Check that refill tube is connected to water control and inserted into
overflow tube without being kinked or damaged.
b. Open supply valve fully. Be sure that proper supply tube size is used.
c. Remove obstruction. Consult a plumber if necessary.
d. Normal supply pressure must be at least 20 psi.
a. Review Step 7 of installation procedure.
b. Review Step 1 through 6 of installation procedure.
a. Clean debris from seal surface. Replace Flapper/Flush Valve seal as
needed. See web for more info.
b. Shut off water supply. Remove cap and clean as per Fluidmaster
maintenance instructions at:
www.americanstandard-us.com/enews/fluidmasterguide.pdf
*c. Readjust chain length as needed.
a. Retighten bowl-to-floor knobs.
b. Use toilet shims and /or place a bead of caulk around the base of
the toilet.
Problem Possible Cause Corrective Action
* for SINGLE FLUSH Models ONLY
* See Step 8 For Diagram TROUBLESHOOTING GUIDE ** for DUAL FLUSH Models ONLY ** See Step 9 For Diagram