American Standard Tropic Deck Kit T038.900 User manual

3/16" DRILLED
HOLE
5
TROPIC TRIM KIT
DECK MOUNT
TUB SYSTEMS
Installation
Instructions
M968896
T038.900
Certified to comply with ANSI A112.18.1
1SPOUT INSTALLATION
U.S. Patent No. D403,750
FINISHED
DECK
REMOVE ALL
BURRS AND
BEVEL
TEMPLATE FOR
SPOUT ROLL
PIN LOCATION
3/16" DIA. HOLE
Drill with 3/16" bit
8.4mm
(21/64")
19.8mm
(23/32")
1"- 2"
FRONT
Complete FINISHED DECK before trim installation.
Turn off the water supplies.
Remove the GUARDS (1) from the VALVE BODIES (2). Remove the
GUARD (3) and 1/4" PLUG (4) from the SPOUT SHANK (5).
The SPOUT SHANK (5) height should be 1" to 2" above the FINISHED
DECK. Cut the SPOUT SHANK (5) if necessary. Remove all burrs
and bevel the end of the shank. Failure to do so may damage
the SPOUT O-ring during installation and cause water leakage.
Drill a 3/16" hole in the finished deckfor spout locking pin. See
TEMPLATE for location.
18.6mm DIA.
(47/64")
SPOUT SHANK
3
4
5
1
1
2
Flat Blade Screwdriver
Adjustable Wrench Channel Locks
Phillips Screwdriver
Required Tools
with EverClean™ Finish
Congratulations on purchasing your American Standard
faucet with EverClean finish found only on American
Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)

M968896
1A SPOUT INSTALLATION
2INSTALL HANDLE ADAPTERS
Place the ESCUTCHEON SEALS (1) into groove of DECK ADAPTERS (2).
Align the HANDLE STEM (3) with the SLEEVE (4) as necessary.
Thread the HANDLE ADAPTER (5) into the VALVE BODY (6) until the
DECK ADAPTERS (2) contacts tight against the finished deck.
GROOVE
Position the RUBBER RING (14) in the groove in
the base of the ESCUTCHEON (11). Push the
SPOUT (12) with ESCUTCHEON (11) down onto
the SPOUT ADAPTER (8) and tighten the SET
SCREW (13) securely with the 5mm HEX
KEY (15) supplied.
GROOVE
Lubricate the SPOUT ADAPTER O-RING (6) and
SPOUT O-RING (7).
Push SPOUT ADAPTER (8) on SPOUT SHANK (5)
and align slot in SPOUT ADAPTER (8) with 3/16"
drilled hole.
Tighten SPOUT ADAPTER SET SCREW (9) securely
with 4mm HEX KEY (10) supplied.
FINISHED
DECK SLOT
3/16" DRILLED
HOLE
1
1
6
5
4
2
6
10 8
8
7
7
5
11
13
12
15
9
11
3
3INSTALL HANDLES
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. See figure "A". Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto DECK
ADAPTER (5) until snug against mounting surface.
Repeat steps for opposite handle.
4
2
5
3
TOP
Figure "A"
SPLINE END DOWN
THREAD ON
TO DECK
ADAPTER
14

M968896
EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
4TESTING
Turn the HOT HANDLE clockwise and the COLD
HANDLE counterclockwise to the off position.
Unscrew and remove the STREAM STRAIGHTENER.
Slowly turn on the water supplies.
Operate the HANDLES to flush water lines thoroughly.
Check SPOUT connection for leakage.
Turn the Handles off. Replace the SPOUT END.
HOT
HANDLE
COLD
HANDLE
STREAM
STRAIGHTENER
5
6
SERVICE
Turn off the water supplies
Turn HANDLE (1) to the off position.
Unthread the HANDLE BASE (2) from HANDLE ADAPTER (3).
Unthread HANDLE ADAPTER (3) and remove.
Remove VALVE LOCKNUT (4). A 17mm deep socket
is required.
Remove the CARTRIDGE (5) by pulling up
on the SLEEVE (6).
Remove SCREW (7) and pull off SLEEVE (6).
Remove the SPRING CLIP (8).
Remove the STOP WASHER (9). Turn it 90˚ and replace.
Replace the SPRING CLIP (8).
Reverse the above steps to reassembly the components.
If the spout drips, operate the handles several times from
the off to the on position. Do not force - the handles only turn 90˚.
90˚
To change the direction of handle rotation
1
3
9
2
4
7
6
8
5
CARE INSTRUCTIONS

TROPIC DIVERTER & PERSONAL
SHOWER TRIM KITS
DECK MOUNT
TUB FILLERS
Installation
Instructions
T038.990
Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
1INSTALL HANDLE ADAPTER
Remove DIVERTER GUARD (1) from valve.
Place the ESCUTCHEON SEAL (7) into groove of DECK ADAPTER (2).
Align the HANDLE STEM (3) with the SLEEVE (4) as necessary.
Thread the HANDLE ADAPTER (5) into the VALVE BODY (6) until
the DECK ADAPTER (2) contacts tight against the finished
mounting surface.
GROOVE
7
6
5
4
2
3
1
with EverClean™ Finish
Congratulations on purchasing your American Standard
faucet with EverClean finish found only on American
Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
2INSTALL HANDLES
1
2
4
5
3
TOP
SPLINE END DOWN
Push ADAPTER (1) on VALVE STEM (2), so that
the hole of the ADAPTER (1) without a spline is
facing up. Fig. A. Tighten STEM SCREW (3) to
secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4)
by adjusting male teeth on ADAPTER (1) to female teeth
in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto DECK
ADAPTER (5) until snug against mounting surface.
THREAD ON
TO DECK
ADAPTER
Fig. A.
M968897

3INSTALL HAND SHOWER
2
3
54
2
6
7
12
8
10
11
13
13
1
1
9
TEST INSTALLED DIVERTER
4
Turn DIVERTER VALVE (1) fully clockwise (Tub fill position).
Lift HANDSHOWER (2) from holder, direct spray into tub, turn
DIVERTER VALVE (1) fully counter-clockwise to check
HANDSHOWER (2) and HOSES (3) for leaks. With DIVERTER
VALVE (1) in counter-clockwise position, flow should only
come from HANDSHOWER (2).
Turn control valves "off."
Turn on control valves and check all connections for leaks. With
DIVERTER VALVE (1) in clockwise position, flow should only come
from tub spout.
1
2
3
5EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
Unscrew the HOLDER (1) from the SHOWER ESCUTCHEON (2). Slip the
SHOWER HOSE (3) through the SHOWER ESCUTCHEON (2) and the
HOLDER (1).
Pull out the SLEEVE GUARD (6) and HOSE (7). Unthread the SLEEVE GUARD
(6) from the HOSE END (8) connection. Be careful not to allow the HOSE
(7) to fall back through the SLEEVE (9).
Insert SEAL WASHER (10) into the SHOWER HOSE CONNECTOR (11).
Thread the SHOWER HOSE CONNECTOR (11) onto the HOSE END (8) and
tighten securely.
Thread the SHOWER ESCUTCHEON (2) into the SLEEVE (9) until the
SHOWER ESCUTCHEON (2) contacts the finished deck.
Loosen the SET SCREW (12) in the SHOWER ESCUTCHEON (2) and rotate
the ESCUTCHEON (2) so that SET SCREW (12) faces the center of the tub.
Retighten the SET SCREW (12).
Thread the HOLDER (1) into the SHOWER ESCUTCHEON (2).
Insert a SEAL WASHER (4) into the SHOWER HOSE CONNECTOR (5)
and hand tighten HAND SHOWER (13) into
SHOWER HOSE CONNECTOR (5).
Place the HAND SHOWER (13)
into the HOLDER (1).
M968897