American Standard Hampton 4770.702 SER. User manual

TOP MOUNT
KITCHEN FAUCETS
Installation
Instructions
M968145D
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
4770.702 SER.
4770.712 SER.
4770.722 SER.
4770.732 SER.
4771.702 SER.
4771.712 SER.
4771.722 SER.
4771.722 SER.
4771.222 SER.
4771.322 SER.
PORCELAIN
LEVER
HANDLE
HANDLE
SCREW
METAL
LEVER
HANDLE
END
CAP
INDEX CAP
WASHER
HANDLE
SCREW
HANDLE
SCREW
HANDLE BASE
(LEVER HANDLE)
HANDLE BASE
(CROSS HANDLE)
LOCKNUT
SPRAY
CAP
SUPPLY
NUT
ADAPTER
AERATOR
CARTRIDGE
INDEX
CAP
PORCELAIN
CROSS
HANDLE
INDEX
CAP
METAL
CROSS
HANDLE
SPRAY
AND HOSE
SPRAY
HOLDER
WING
NUT

M968145D
1INSTALL FAUCET
Turn off hot and cold water supplies before beginning.
CAUTION
Place faucet in position on sink.
Assemble and tighten LOCKNUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the
COLD water supply to the right SHANK using sealant,
appropriate connectors, and COUPLING NUTS.
To install SPRAY:
Screw SPOUT onto BODY.
LOCKNUT
HOT
COLD
COUPLING
NUT
SPRAY HOSE
COUPLING NUT
PUTTY
BODY
SINK
HOSE
SHANK WING
NUT
SPRAY
HOLDER
Place the HOLDER into the appropriate mounting hole.
Assemble the SPRAY HOLDER WING NUT onto the shank
of SPRAY HOLDER from below and tighten.
From underneath sink, attach COUPLING NUT of SPRAY HOSE
to HOSE SHANK. Tighten COUPLING NUT firmly.
Feed SPRAY HOSE through HOLDER so SPRAY sits in HOLDER.
SPRAY
HOSE
Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1998
C
Unscrew SPRAY CAP.
SPRAY
CAP
TEST INSTALLED FAUCET
2
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate SPRAY (if present).
Operate both handles to flush water lines thoroughly.
Turn handles into OFF position and replace AERATOR.
Check alignment, if not satisfactory
aligned;
Push out ADAPTER carefully.
Turn ADAPTER either 45˚ or 90˚
so that male square on
ADAPTER catches different
female square in HANDLE BASE.
Assemble and tighten
MOUNTING SCREW.
Push INDEX CAP in top of
HANDLE.
SERVICE Handle alignment.
3
To change direction of handle rotation,
proceed as follows:
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
SPRING
CLIP
STOP
WASHER
90°
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90°and replace.
Replace SPRING CLIP.
Reinstall HANDLE.
VALVE
STEM
FEMALE SQUARE
IN HANDLE BASE
HANDLE
ADAPTER
SQUARE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST