American Standard Silhouette 25 User manual

G35
© 2008 AS America Inc.
SILHOUETTE™ 25" SINGLE BOWL KITCHEN SINK
• Americast® brand engineered material
• Single bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Tile edge installation
• Silicone sealant supplied
• Available in 1, 3 or 4 faucet hole conguration
• Customized hole punchings available
(see page G56)
Tile Edge:
❏ 7172.011 Center hole only
❏ 7172.813 3 hole
❏ 7172.814 4 hole
Nominal Dimensions:
635 x 559 x 241mm
(25" x 22" x 9-1/2")
Bowl sizes:
552mm (21-3/4") wide
476mm (18-3/4") front to back
229mm (9") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Trap:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
❏ Bottom Sink Rack: 7404.100, Color:
SILHOUETTE™ 25"
SINGLE BOWL SINK
AMERICAST®
Revised 2/08
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

G36
© 2008 AS America Inc.
7172.813/814
FINISHED WALL
OR SPLASHBACK
*CUTOUT NOTE
7172.814
4 HOLE
C/L
SEALING
COMPOUND
FINISHED
FLOOR
TILED
COUNTERTOP
(BY OTHERS)
9-1/8"
(232mm)
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
5-3/4"
(146mm)
2" (51mm)
OPTIONAL
7-7/8"
(200mm)
3-1/2"
(89mm)
DIA.
22"
(559mm)
3/8"
(10mm)
12-1/2"
(318mm)
25"
(635mm)
3/4"
(19mm)
5-7/8"
(149mm)
2-1/8"
(54mm)
1-1/2" (38mm)
DIA. HOLES TYP.
3"
(76mm)
4"(102mm)
4"
(102mm)
NOTES:
* COUNTERTOP CUTOUT 603mm x 527mm WITH 25mm RADIUS
(23-3/4 X 20-3/4 WITH 1” RADIUS) AT CORNERS.
■ ON FOUR HOLE VERSIONS, SPACING BETWEEN FAR RIGHT
HOLES IS 3".
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
SILHOUETTE™ 25"
SINGLE BOWL SINK
AMERICAST®
Revised 2/08