American Standard Silhouette 7183.801 User manual

G17
© 2008 AS America Inc. Revised 2/08
SILHOUETTE™ TRIPLE BOWL KITCHEN SINK
• Americast® brand engineered material
• Triple bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid Resisting Glossy Porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available in 1, 3, 4, or 5 faucet hole
conguration
• Customized hole punchings available
(see page G56)
Top Mount/Undercounter:
❏ 7183.001 Center hole only
❏ 7183.803 3 hole
❏ 7183.804 4 hole
❏ 7183.805 5 hole
Undercounter Installation Order:
❏ 791239-100 Mounting Kit (consists of
cut-out templates and mounting clips)
Nominal Dimensions:
1054 x 559 x 241mm
(41-1/2" x 22" x 9-1/2")
Bowl sizes:
Right Hand: 359mm (14-1/8") wide
413mm (16-1/4") front to back
229mm (9") deep
Center: 91mm (7-1/2") wide
413mm (16-1/4") front to back
178mm (7") deep
Left Hand: 359mm (14-1/8") wide
476mm (18-3/4") front to back
229mm (9") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for available models
To Be Specied:
❏ Color (specify color):
❏ Faucet* (specify nish):
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, (specify color):
❏ Traps:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
❏ Web Cover: 8106.100, Color:
❏ Bottom Sink Rack (Left): 7405.100, Color:
❏ Bottom Sink Rack (Right): 7406.100, Color:
SILHOUETTE™
TRIPLE BOWL SINK
AMERICAST®
Top Mount Installation
Undercounter Mount Installation
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

G18
© 2008 AS America Inc.
7183.803/804/805 Top Mount
Undercounter Mount
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791239-100 FOR
EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK
COUNTERTOP CUTOUT VARIATIONS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
SILHOUETTE™
TRIPLE BOWL SINK
AMERICAST®
NOTES:
* COUNTERTOP CUTOUT 1022mm x 527mm WITH 25mm RADIUS
(40-1/4 X 20-3/4 WITH 1" RADIUS) AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
8-5/8"
(219mm)
5-3/4"
(146mm)
8"
(203mm)
1-1/2 O.D. TAILPIECE 1-1/2"O.D. TAILPIECE
COUPLING NUTS
ON FITTING
SEALING
COMPOUND
COUNTERTOP
(BY OTHERS)
1/2"
(13mm)
X
Y
36"(914mm)
SUGGESTED
FINISHED FLOOR
5-3/4"
(146mm)
5-3/4"
(146mm)
165mm
(6-1/2)
3/8"O.D.
BENDABLE
TUBING
2-1/8"
(54mm)
2"(51mm)
OPTIONAL
FINISHED WALL
OR SPLASHBACK
4"(102mm)
1-1/2"(38mm)
DIA. HOLES TYP.
C/L
22"
(559mm)
7183.804
4 HOLE
7183.805
5 HOLE
4"
(102mm) 4"
(102mm)4"
(102mm)
3-1/2"
(89mm)
DIA.
7-3/8"
(187mm)
8-5/8"
(219mm)
14-5/8"
(372mm)
12-1/4"
(311mm)
20-3/4"
(527mm)
41-1/2"
(1054mm)
*CUTOUT NOTE
1-1/2"(38mm)
RAD. TYP.
9-1/8 "
(232mm)
5-3/4 "
(146mm)
7 "
(178mm)
1-1/2 " O.D. TAILPIECE 1-1/2
" O.D. TAILPIECE
SEALING
COMPOUND COUNTERTOP
(BY OTHERS)
36 " (914mm)
SUGGESTED
FINISHED FLOOR
5-3/4 "
(146mm)
5-3/4 "
(146mm)
6-1/2 "
(165mm)
2-1/8 "
(54mm)
2 " (51mm)
OPTIONAL
FINISHED WALL
OR SPLASHBACK
4 " (102mm)
1-1/2 " (38mm)
DIA. HOLES TYP.
C/L
22 "
(559mm)
7183.804
4 HOLE
7183.805
5 HOLE
4 "
(102mm)
4 "
(102mm) 4
"
(102mm)
3-1/2 "
(89mm)
DIA.
7-3/8 "
(187mm)
8-5/8 "
(219mm)
14-5/8 "
(372mm)
12-1/4 "
(311mm)
20-3/4 "
(527mm)
41-1/2 "
(1054mm)
* CUTOUT
NOTE
1-1/2 " (38mm)
RAD. TYP.
MOUNTING CLIP
(SEE DETAIL)
DETAIL OF MOUNTING CLIP
(KIT No.791239-100)
BRASS
INSERT
1/2 "
(13mm)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
Revised 2/08