American Standard Standard 4210 User manual

SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
Installation
Instructions
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
4210
1
3
4
5
6
7
AB
8
CAUTION
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Turn off hot and cold water supplies before beginning.
PUTTY
SPOUT BASE
SINK OR
MOUNTING
SURFACE
7
2
3
byCOLLECTION
™
THE
4
5
6
8
2
M968461B
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
TOOLS REQUIRED
Regular Screwdriver

M968461B
2MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
1
2
COLD
HOT
RED TAG
RED
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Tag)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
4TEST INSTALLED FAUCET
3
Place WASHER (3) into COUPLING NUT (1)
on HOSE (2). Thread COUPLING NUT (1) onto
HAND SPRAY (4) and tighten.
(May already be assembled).
Slide COUPLING NUT (1) onto HOSE (2)
Feed small end of HOSE (2) through BODY (5) so
HAND SPRAY (4) rests inside SPRAY HOLDER (6).
Thread HOSE END (7) onto OUTLET HOSE ADAPTER (8)
and tighten.
CONNECT SPRAY HOSE
Move HANDLE (1) down into "off"
position.
With HANDLE (1) down in "off"
position.
Turn on water supplies.
Operate handle up and down, in COLD and HOT positions, to
flush water lines thoroughly.
Place WASHER (7) into HOSE END (4) and connect
HAND SPRAY (2) to HOSE END (4). Place HAND SPRAY (2)
back into faucet.
Pull HAND SPRAY (2) from FAUCET (5)
and disconnect HAND SPRAY (2). Be
careful not to lose WASHER (7). Pull
HOSE (3) (HOSE should pull
approximately 2 feet) and direct open
HOSE END (4) into sink.
Check HAND SPRAY (2) operation:
With faucet on push front of BUTTON (6) for a broad
cleansing spray.
With HAND SPRAY (4) seated in SPRAY HOLDER (6),
install WEIGHTS (9) onto HOSE (2) using two SCREWS (10).
Locate the WEIGHTS (9) two feet (2') from the underside of
the sink deck. Tighten SCREWS (10) firmly.
1
5
3
2
4
6
7
2
910
8
1
35
2
6
4
24"
7
Check connections for leaks. (See
Section 5)

M968461B
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE down into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
5
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
3
1
2
4
5
6
6
6A 8
7
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and and blot dry
with a cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing acids,
polish abrasives, or harsh cleaners or soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
7
Failure to follow these care instructions may
damage the faucet's finish.
CARE INSTRUCTIONS
RED
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Pull off ESCUTCHEON CAP (4). Unscrew three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6A).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red HOT LIMIT
SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max.
discharge temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"A"
"B"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
"RED RING"- HOT
LIMIT SAFETY STOP
TEMPERATURE
SETTING NUMBERS
0
1
2
3
4
5
6
7
5

M968461B
MODEL NUMBERS
M962301-0070A
INTERNAL BODY
AND SEAL
M901142-YYY0A
BODY
023529-0070A
CARTRIDGE
023527-0070A
CARTRIDGE SCREWS
050448-0070A
WEIGHTS
M962302-0020A
SPRAY HOSE
AND SEAL
M962299--YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
CHROME
SATIN
002
295
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
4210
A907086-YYY0A
ESCUTCHEON CAP
A912746-0070A
O-RING
M952234-YYY0A
PULL-OUT SPRAY
M953052-0070A
FLOW REGULATING
CHECK VALVE
A922804-0070A
SPRAY HOLDER
SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
M962295-YYY0A
HANDLE KIT
M962294-0070A
BUTTON AND
SCREW KIT
M918504-0070A
SCREW
A953051-0070A
CHECK VALVE
IN MEXICO 01-800-839-12-00
A911714-0070A
SEAL WASHER