American Standard Elevate AM00841400 User manual

THE BEST BATH OR SHOWER EXPERIENCE?
THE ONE NOBODY INTERRUPTS.
Thank you for buying an American Standard
bath or shower product.
We’re so grateful you did, and you will be too. Not just while you’re waking
up each morning, but also every time a dirty gardener, sweaty soccer player,
or muddy dog gets cleaned up. How do we know? Just like you, we’ve lived
with that same beautiful chaos called life for almost 150 years. We believe
that while every home should appreciate in value, we never forget the
sentimental value that grows from enjoying life in the heart of home—
your kitchen and bath. That’s why we love your stories and ideas; they help
us innovate with products that make your life easier.
Or, visit americanstandard-us.com/bathroom/tub-and-shower-
doors to watch video, view/download installation manuals
or learn more about your product.
Have a question or need help on install?
For questions or help on installation call us at 800-442-1902.
For a copy of our warranty in additional languages,
please visit Americanstandard.com

OWNERS MANUAL
Elevate™Neo-Angle Shower Door
AM00841400
INSTALLATION INSTRUCTIONS
Thank you for selecting American Standard – the benchmark of fine quality for over 150 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. Certain installations may
require professional help. Also be sure your installation conforms to local codes.
INSTALLATION PREPARATION
• Please unpack carefully and identify all parts needed for installation by using the Box Contents page as a
reference. Inspect the product and report any damages or missing parts immediately to customer care by
calling 800-442-1902. Follow the prompts for consumer/shower doors.
• These Elevate shower doors were developed to be installed with the Elevate shower base and Elevate
shower walls. If you are using a different base and wall set, you may need additional hardware and tools to
complete the installation.
• Handle the glass panels carefully and protect the edges. Unequal pressure applied during installation can
cause cracking or breakage, and the sharp corners on the glass panels can cause damage to the wall or
floor materials.
• Ensure adequate wall support is provided to area where shower door is to be installed.
• Shower base and wall material must be installed prior to the door installation.
• Wear protective equipment during installation to avoid injury.
• Please keep these instructions for after care and customer service details.
!WARNING: PRODUCT IS HEAVY AND REQUIRES TWO PEOPLE FOR INSTALLATION.
!WARNING: TEMPERED GLASS CANNOT BE DRILLED, CUT OR MODIFIED.

BEFORE YOU BEGIN
Inspect your product thoroughly before installing. Take extra care in handling surfaces
of the bath and use only non-abrasive cloths to avoid scratching. Observe all local plumbing
and building codes.
INSIDE THE BOX
RECOMMENDED TOOLS AND MATERIALS
Level
Left Hand Opening Right Hand Opening
Utility Knife
Installation steps will indicate which tools should be used with asscociated letter
Hammer Pencil
Tape
Measure
Caulking Gun Drill
1/4"(6 mm))
Drill Bits #2 Square Drive Bit
1/8"(3.2 mm)
Drill Bits #2 Square Drive Bit
Phillips
Screwdriver
Regular
Screwdriver
Safety
Equipment
B
H
L
I J
ACD
FG
E
K
Drill 1/4" (6mm) & 1/8" (3.2mm)
Drill Bits #2 Square Drive Bit
Drill 1/4" (6mm) & 1/8" (3.2mm)
Drill Bits #2 Square Drive Bit
Image shown may vary from product purchased.

BOX CONTENTS
1x Installation Instruction
[1] 2x Wall Posts
[2] 2x Side Covers
[3] 1x Support Bar
[4] 1x Bottom Threshold
[5] 1x Bottom Gasket
[6] 1x Side Gasket
[7] 1x Magnetic Seal
[8] 1x Magnetic Seal
[9] 1x Door Panel
[10] 1x Fixed Panel A
[11] 1x Fixed Panel B
[12] 1x Handle Set
[13] 2x Hinges
[14] 6x Screws M4x16
[15] 6x Adjust Fixtures
[16] 2x Screws ST4x35
[17] 2x Wall Brackets
[18] 6x Caps
[19] 1x Fixing (L)
[20] 1x Fixing (R)
[21] 2x Screws ST4x25
[22] 10x Wall Anchors
[23] 8x Screws ST4x35
[24] 1x 2.5mm Allen Key
[25] 1x 4mm Allen Key
[26] 1x Hole Location Template
[27] 2x Gaskets

ASSEMBLY DRAWING
[1] 2x Wall Posts
[2] 2x Side Covers
[3] 1x Support Bar
[4] 1x Bottom Threshold
[5] 1x Bottom Gasket
[6] 1x Side Gasket
[7] 1x Magnetic Seal
[8] 1x Magnetic Seal
[9] 1x Door Panel
[10] 1x Fixed Panel A
[11] 1x Fixed Panel B
[12] 1x Handle Set
[13] 2x Hinges
[14] 6x Screws M4x16
[15] 6x Adjust Fixtures
[16] 2x Screws ST4x35
[17] 2x Wall Brackets
[18] 6x Caps
[19] 1x Fixing (L)
[20] 1x Fixing (R)
[21] 2x Screws ST4x25
[22] 10x Wall Anchors
[23] 8x Screws ST4x35
[24] 1x 2.5mm Allen Key
[25] 1x 4mm Allen Key
[26] 1x Hole Location Template
[27] 2x Gaskets
[22]
[23]
[14]
[15]
[03][01]
[02]
[06][09]
[10]
[11]
[17]
[05]
[16]
[18]
[13]
[24]
[25]
[04]
[19][20]
[07][08]
[12]
[21][26]
[27]

DETERMINING DOOR OPENING SIDE
NOTE: Before installing the shower door, determine the door opening side. If it is to be a Left Hand Opening
(as illustrated), proceed to step 1. If it is to be a Right Hand Opening (as illustrated), disassemble both
hinges as per the images below and reassemble to prepare the hinges for Right Hand Opening.
[09]
[09][10]
[10]
Left Hand Opening Right Hand Opening

INSTALLATION INSTRUCTIONS
IMPORTANT GENERAL INFORMATION
This unit is best installed by two people.
Cover drain with tape prior to installation to prevent the loss of small parts.
Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using Box
Contents and Assembly Drawing as a reference. Before discarding the carton check to see that no
small hardware parts have fallen to the bottom of the box. If any parts are damaged or missing refer to
the description noted in the instructions when inquiring about replacements.
Handle the glass panels carefully and protect the edges. Although tempered glass is very resistant to
breakage, the glass can still break if unequal pressure is applied during installation and the sharp corners
of the panel can damage tile and flooring surface.
Be sure to wear safety glasses whenever drilling or cutting. When drilling holes in ceramic tile or marble
use a center punch and hammer to carefully break the glazed surface. This will prevent skidding
when drilling.
NOTE: TEMPERED GLASS CANNOT BE DRILLED, CUT OR MODIFIED.

1INSTALLING WALL POSTS
1a. Measure from the outside edge of the base deck 3/4"to 1"(19 to 25 mm) (ref. main illustration near
bottom) and mark deck of base. Place outside edge of Wall Post [1] (slot where glass panel goes) onto
mark on base deck and plumb using Level [B]. Tape Wall Post [1] to shower wall to temporarily hold in
place. Mark all predrilled holes in Wall Post [1] with a pencil [J]. Repeat procedure for Wall Post [1] on
opposite side.
1b. If using supplied Wall Anchors [22] drill each of the marks on the wall from step 1a using a 6mm drill bit.
If not using Wall Anchors, drill using appropriate size bit for screw being used.
1c. If using Wall Anchors [22], place into each drilled hole.
1d. Place either left or right Wall Post [1] on the wall and screw into place using ST4x35 [23] screws. Ensure
Wall Post [1] is in correct position (ref illustration).
1e. Slide the Hole Location Template [26] all the way down over left Wall Post [1]. NOTE: the “L” stamped
into the Hole Location Template [26] indicating LEFT.
1f. Mark the hole in the Hole Location Template [26] with a pencil [J].
1g. Remove Hole Location Template [26] and drill marked location on shower wall with a 6mm Drill Bit [D]
if using Wall Anchor [22].
1h. Insert Wall Anchor [22] into drilled hole. Tap into place with Hammer [I].
• In this step, you’ll need following parts: [1] x2, [22] x8, [23] x8, [26] x1
• In this step, you’ll need the following tools: B, C, D, G, I, J
6mm
L
L
6mm
L
R
1a
≈ 3/4"-1"
19-25 mm
View from
Outside
1a
[1]
[1]
[22]
[23]
Round Head Screw ST4x35
[1]
[1]
[26]
[26]
[26]
[26]
[1]
1a 1e
1b
J
C
B
I
J
D
D
1c
1d
1f
1g
1h
View from
Outside
[1]
Shower
Wall
Shower
Wall
Shower
Wall
Shower
Wall
G
[22]I
B
C

2INSTALLING FIXED PANEL A & B
2a. Insert Fixed Panel A [10] into narrow slot of Wall Post [1].
2b. Ensure Fixed Panel A [10] fully fits into the channel of Wall Post [1].
2c. Insert Adjust Fixtures [15] into notches of the Wall Post [1] and lightly screw into place using M4x16
Screw [14] at 3 locations.
2d. Level [B] Fixed Panel A [10] and fully tighten each of the M4x16 Screws [14]. Install Fixed Panel B [11]
in the same way.
• In this step, you’ll need following part: [10] x1, [11] x1, [15] x6, [14] x6
• In this step, you’ll need the following tool: G
[10]
[15]
[14]
Screw
M4x16
G
View from Inside
View from Inside
View from Outside
View of
Countersunk
Hole
[11]
View from
Inside
B
2a 2c
2b 2d
[10]
[1]
[1]
[1]
[1]
[15]
[10]
[10]
[10]
[15]

3INSTALLING DOOR PANEL AND HINGES
• In this step, you’ll need following parts:[4] x1, [6] x1, [9] x1, [13] x2, [19] x2
[10]
[10]
Correct Alignment Incorrect Alignment
View from
Inside
[11]
[9]
View from
Outside
3c
3b
3a
[10] [9] [10] [9]
[10]
[10]
[9] [9]
[9]
3b
3a
3e
3c
3f
3d
[19]
[4]
[13]
[13]
[13]
[10]
[13]
[25]
[6]
[10]
[10]
3a
3e
View from
Inside
3a. Slide notch of Fixing L [19] into bottom of Fixed Panel A [10]. Attach Bottom Threshold [4] into opposite
side of Fixing L [19] as illustrated. Attach Fixing R [20] onto Fixed Panel B [11] and Bottom Threshold [4]
in the same way on the opposite side.
3b. Press Side Gasket [6] fully onto edge of Fixed Panel A [10].
3c. On one side of Hinge [13] remove the two screws and plastic washers as illustrated. Repeat for second
Hinge [13]. Attach one of the Hinges [13] at the holes of Fixed Panel A [10], then place the plastic washer
and screw into the hole. Ensure the plastic washer stays within the hole of the Fixed Panel A [10] and
lightly tighten the two screws. Repeat installation for the second Hinge [13] onto Fixed Panel A [10].
3d. Remove the single screw and washer from both Hinges [13]. Carefully position and install Door Panel [9]
over each of the Hinges [13] and insert the washer and screw into each hole of Door Panel [9] keeping the
washer within the hole of the door panel. Lightly tighten both screws.
3e. Observe that both Hinges [13] are straight and even (ref. illustration 3e). Once both hinges are straight,
securely tighten all screws on both hinges using supplied 4mm Allen Key [25].
3f. Snap cover caps over each screw of both Hinges [13] to cover screws.