American Standard PEKOE EXTENDER M968582 User manual

SINGLE CONTROL KITCHEN
POP-OUT SPRAY
Installation
Instructions
M968582 REV.1.1
Certified to comply with ANSI A112.18.1M
4335.020.XXX
CAUTION
1INSTALL FITTING
Turn off hot and cold water
supplies before beginning.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
Recommended Tools
Make certain the SEAL (1) is properly seated in recess
of faucet body.
Insert supply HOSES (2) and SHANK (3) through center
hole of sink or mounting surface.
Assemble RUBBER WASHER (4), PLASTIC WASHER (5),
METAL WASHER (6) and threaded LOCKNUT (7) onto
SHANK (3) from underside of sink or mounting surface.
Hand tighten LOCKNUT (7) and check that faucet is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (7).
Work your way around LOCKNUT (7), tightening the screws
slightly each time until all are snug to ensure even pressure.
Tubing Cutter
1
2
5
RECESS
PEKOE EXTENDER
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
4
3
6
7
8

M968582 REV.1.1
RED
STRIPE
BLUE
STRIPE
2MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection
on fitting supplies are 3/8" compression. Connect left supply
(Marked with a Red Stripe) to Hot and right supply (Marked with
Blue Stripe) to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 27-1/2" long from faucet base.
Note: If additional supply length
is required, installer must
purchase additional parts
separately.
Important: If SUPPLY HOSES
(1, 2) are too long, loop as
illustrated to avoid kinking.
1
2
COLD
HOT
3
3TEST INSTALLED FAUCET
Unthread SPRAY END (2) from SPOUT (3).
Turn on water supplies and check connections for leaks.
Operate HANDLE (1) on and off, hot and cold to flush water
lines thoroughly. Replace SPRAY END (2).
Check all drain connections for leaks.
Move HANDLE (1) to "off" position.
1
2
3
HOT & COLD SUPPLIES
Move HANDLE (1) into "off" position.

M968582 REV.1.1
2
1
3
SERVICE
5
Loosen and remove LEVER HANDLE (1). Loosen
HANDLE SCREW (2) with 2.5mm Hex Wrench and
then pull HANDLE BASE (3) off.
Unscrew ESCUTCHEON CAP (4). Unscrew the
CARTRIDGE NUT (5) and remove METAL WASHER (8).
Remove CARTRIDGE (6). Clean inlets of
CARTRIDGE (6) and MANIFOLD (7).
Reassemble CARTRIDGE (6). Replace CARTRIDGE
NUT (5), CAP (4), METAL WASHER (8) and
HANDLE assembly, check flow.
SERVICE
Clogged CARTRIDGE outlets or inlets may cause reduced
flow. To clean, first turn off water supply then:
If SPOUT (1) leaks at swivel point the O-RINGS (2) need
to be replaced. To remove SPOUT (1):
Turn faucet to off position. Loosen the SPOUT SET SCREW (3)
with a 3mm Hex wrench.
Rotate the SPOUT (1) side to side while pulling upward to
remove SPOUT (1) from faucet body.
Replace the defective parts and grease O-RINGS (2). Push
SPOUT (1) back into position. Tighten SET SCREW (3).
Check that SPOUT (1) rotates freely and does not leak
at the swivel point.
4
6
REMOVE
INSTALL
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
2
3
1
8
4
5
6
7
CLEAN
METAL
WASHER
3mm HEX
WRENCH