American Standard Silhouette 7145.001 User manual

G27
© 2008 AS America Inc. Revised 2/08
SILHOUETTE™ 33" DOUBLE BOWL
KITCHEN SINK
• Americast® brand engineered material
• Dual level double bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available in 1, 3, 4, or 5 faucet hole
conguration
• Customized hole punchings available
(see page G56)
Top Mount/Undercounter:
❏ 7145.001 Center hole only
❏ 7145.803 3 hole
❏ 7145.804 4 hole
❏ 7145.805 5 hole
Undercounter Installation Order:
❏ 791326-100 Mounting Kit (consists of
cut-out templates and mounting clips)
Nominal Dimensions:
838 x 559 x 241mm
(33" x 22" x 9-1/2")
Bowl sizes:
Right Hand: 359mm (14-1/8") wide
413mm (16-1/4") front to back
229mm (9") deep
Left Hand: 359mm (14-1/8") wide
476mm (18-3/4") front to back
229mm (9") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SILHOUETTE™ 33"
DOUBLE BOWL SINK
AMERICAST®
Top Mount Installation
(faucet & soap dispenser not included)
Undercounter Mount Installation
(faucet not included)
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, (specify color):
❏ Traps:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
❏ Web Cover: 8106.100, Color:
❏ Bottom Sink Rack (Left): 7405.100, Color:
❏ Bottom Sink Rack (Right): 7406.100, Color:

G28
© 2008 AS America Inc.
7145.803/804/805 Top Mount
Undercounter Mount
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791326-100 FOR
EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK
COUNTERTOP CUTOUT VARIATIONS.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED
AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
NOTES:
* TOP MOUNT (7145.803/4/5): COUNTERTOP CUTOUT
806 X 527mm WITH 25mm RADIUS (31-3/4 X 20-3/4 WITH 1" RAD.)
AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
7145.804
4 HOLE
7145.805
5 HOLE
C/L
FINISHED WALL
OR SPLASHBACK
1-1/2" O.D.
TAILPIECE
FINISHED
FLOOR
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
*CUTOUT NOTE
9-1/8"
(232mm)
1/2"
(13mm)
5-3/4"
(146mm)
22"
(559mm)
36" (914mm)
SUGGESTED
16-1/2"
(419mm)
33"
(838mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
RAD. TYP.
2-1/8"
(54mm)
1-1/2" (38mm)
DIA. HOLES TYP.
4" (102mm)
4" (102mm)
4" (102mm)
4" (102mm)
2" (51mm)
OPTIONAL
7-7/8"
(200mm)
8-5/8"
(219mm)
7-7/8"
(200mm)
10-1/8"
(257mm)
7145.804
4 HOLE
7145.805
5 HOLE
C/L
FINISHED WALL
OR SPLASHBACK
FINISHED
FLOOR
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
* CUTOUT
NOTE
MOUNTING CLIP
(SEE DETAIL)
DETAIL OF MOUNTING CLIP
(KIT No.791002-100)
BRASS
INSERT 3/4
"
(19mm)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
1-1/2" O.D.
TAILPIECE
36" (914mm)
SUGGESTED
16-1/2"
(419mm) 33"
(838mm)
7-7/8"
(200mm)
10-1/8"
(257mm)
9-1/2"
(241mm)
5-3/4 "
(146mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
RAD. TYP.
4" (102mm)
2" (51mm)
OPTIONAL
7-7/8"
(200mm)
8-5/8"
(219mm)
22"
(559mm)
2-1/8"
(54mm)
1-1/2" (38mm)
DIA. HOLES TYP.
4" (102mm)
4" (102mm)
4" (102mm)
SILHOUETTE™ 33"
DOUBLE BOWL SINK
AMERICAST®
Revised 2/08