American Standard Standart T6280 User manual

Dimensions are for reference.
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these
instructions carefully before you begin.
ROUGHING-IN DIMENSIONS
Installation for Bath/Shower,
Shower only, or Valve only rim.
Certified to comply with ANSI A112.18.1
M968289
Installation
Instructions
1INS ALL
RIM
hen finished tiling the wall, remove PLASTER GUARD (A)
and turn off water supply.
Push CAP (1) over VALVE CARTRIDGE (2).
Mount ESCUTCHEON (3) to valve body with SCRE S (4).
Push DIAL PLATE (9) over CAP (1) and into the three alignment holes
in ESCUTCHEON (3).
Remove PIPE CAP (5) and PIPE PLUG (9) from shower pipe and
tub filler pipe.
Install SHO ER ARM (6), SHO ER HEAD (7) and TUB FILLER SPOUT
(8) by threading onto pipe nipples using teflon tape or pipe sealant.
Install HANDLE (10) onto CARTRIDGE STEM (11). Tighten SET SCRE (12)
with HEX RENCH (13) supplied with fitting to secure HANDLE (10).
Push INDEX BUTTON (14) into set screw opening in HANDLE (10).
CAU ION: Protect finish on SHOWER ARM,
SHOWER HEAD and UB SPOU when installing.
BA H/SHOWER
RIM KI S
6280
6281
6282
FINISHED ALL
4"
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
5-1/8" REF.
7-1/2" REF.
18" OPTIONAL
5-5/8" REF.
1/2" NPT
1/2" NPT
7-1/8"
1" MIN.
TOP OF TUB RIM
by
COLLECTION
™
“”
THE
CARE INS RUC IONS:
DO: SIMPLY RINSE HE PRODUC CLEAN WI H
CLEAR WA ER. DRY WI H A SOF CO ON
FLANNEL CLO H.
DO NO : CLEAN HE PRODUC WI H SOAPS,
ACID, POLISH, ABRASIVES, HARSH CLEANERS,
OR A CLO H WI H A COARSE SURFACE
Required ools
Flat Blade Screwdriver
Adjustable rench
Channel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
6
7
3
1
11
9
2
A
5
8
9
4
10
(3) ALIGNMENT
HOLES FOR
DIAL PLATE
13
14
12

2
Remove HANDLE and TRIM. See step one and reverse assembly procedure.
O GAIN ACCESS O VALVE FOR SERVICING
Remove CARTRIDGE (1) by removing CARTRIDGE SCRE S (2). Remove three SCRE S (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove
CAPS (7) and check O-RINGS on inside of CAPS (7) for debris. Clean inside sealing surfaces of VALVE BODY (8).
Reassemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.
Turn on water supply. If it still leaks, replace pressure balancing unit (M952100-0070A). See step one for installing
TRIM and HANDLE.
VALVE LEAKS WHEN SHU OFF
Remove PRESSURE BALANCE UNIT (5).
Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
UNABLE O MAIN AIN CONS AN EMPERA URE
M968289
ES INS ALLED FI ING
4
Turn VALVE (1) "off".
ith HANDLE (2) in "off" position, turn
on water supplies and check all connections
for leaks.
Operate HANDLE (2) and flush water
lines thoroughly. Pull DIVERTER (3) up
and check SHO ER (4) for proper
operation.
Check SPOUT (5) and SHO ER (4)
connections for leaks.
1
2
3
4
5
6
7
89
HANDLE and TRIM
ADJUS HO LIMI S OP
3
1
3
2
4
"B""A"
ADJUS MEN WHEN
WA ER IS OO HO
PRY OUT ARD TO UNLOCK AND
ROTATE
OUNTER- LO KWISE
ONE CLICK.
ADJUS MEN WHEN
WA ER IS OO COLD
PRY OUT ARD TO UNLOCK
AND ROTATE
LO KWISE
ONE CLICK.
By restricting HANDLE rotation and limiting the
amount of hot water allowed to mix with the cold, the
HOT LIMIT SAFETY STOP (1) reduces risk of accidental
scalding. To set the maximum hot water temperature
of your faucet, all you need to do is adjust the setting
on the HOT LIMIT SAFETY STOP (1).
Remove PLUG BUTTON (2). Loosen HANDLE SCRE (3)
and pull off HANDLE (4).
Replace CARTRIDGE CAP (5) and HANDLE (4). Tighten
HANDLE SCRE (3). Replace PLUG BUTTON (2).
Pull off CARTRIDGE CAP (5).
See "A" and "B" for HOT LIMIT STOP (1) adjustment.
5
11
1
2
3
5
4

MODEL NUMBER
M968289
BA H/SHOWER
M962167-YYY0A
ESCUTCHEON AND SCRE S
M907050-YYY0A
ESCUTCHEON CAP SET
078016-YYY0A
ESCUTCHEON SCRE S
M953575-YYY0A
SHO ER HEAD
M909659-0070A
DIAL PLATE
M953415-YYY0A
DIVERTER SPOUT (IPS)
M907557-YYY0A
TUB SPOUT
ESCUTCHEON
M962168-0070A
DIVERTER SPOUT
REPAIR KIT
060351-YYY0A
SHO ER ARM AND FLANGE
by
COLLECTION
™
“”
THE
CHROME
SATIN 002 295
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
eekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
eekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
6280
6281
6282
M962240-YYY0A
INDEX HANDLE KIT
M962241-YYY0A
HANDLE KIT