American Standard Town Square Deck-Mount Bath Filler 2555.900 User manual

TOWNSQUARE
Certified to comply with ANSI A112.18.1M
ROUGHING-IN
DIMENSIONS
Required Tools
Wrench
(Supplied)
Turn off hot and cold water supplies before beginning.
CAUTION
12
Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (2) is properly seated in RECESS
at base of SPOUT (3).
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto
SHANK (1). From underside of ledge secure SPOUT (3) into position
with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
Adjustable Wrench
Channel Locks
2555.900
2555.901
Flat Blade Screwdriver
VALVE inlet is 3/4-inch NPT male connector.
NOTE
2
ADJ. 6-1/2 TO 12
43
1
3
4
5
RECESS
3
1
2
4
6
5
MOUNTING
LEDGE.
MOUNTING
SURFACE
8-1/4
3-5/8
4
ADJ. 6-1/2 TO 12
1-1/2 MAX.
1-1/4
MAX.
1-3/16 D.
3
(H) (C)
1-1/8 D.
3/4-14 MALE
N.P.T. INLETS
12 MAX
1-1/16 D.
Phillips Screwdriver
.3FW
DECK-MOUNT BATH FILLER
with EverClean™ Finish
Congratulations on purchasing your American
Standard faucet with EverClean finish found
only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
IMPORTANT NOTICE TO INSTALLER!
Please check with local Code Authority for the installation requirements of this product. Some codes require an
additional temperature mixing valve to limit the maximum hot water temperature and vacuum breaker
(for products with hand spray) to be installed with this product.
Installation
Instructions

10
3
5
5/16'' MIN. MOUNTING SURFACE
11
11
10
11
1
3
Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)
into mounting holes from underside of ledge.
Install LOCKNUTS (1) and RUBBER WASHERS (3) onto valve shanks.
Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (5) position.
Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten
COUPLING NUT (14) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
13
5
14
8
7
9
9a
6
14
13
45
10
MOUNTING
LEDGE
DECK ADAPTER
4INSTALL HANDLES
1
2
3
4
5
6
7
10
Figure B
Figure A
Figure D
Figure C
4
5
6
10
5
10
8
Turn VALVE to OFF position.
Figure A: Install STEM ADAPTERS (7) onto VALVE STEMS (8).
Figure B: With colored side up, place FRICTION RING (6) over DECK ADAPTER (10). Loosely screw FRICTION NUT (5)
onto DECK ADAPTER (10). Do not tighten. Align flats on FRICTION NUT (5) with RIBS (9) in HANDLE BASE (4).
Figure C: Screw HANDLE BASE (4) with FRICTION NUT (5) onto DECK ADAPTER (10) until snug against mounting
surface and aligned properly.
Figure D: Install LEVER HANDLE (3) onto HANDLE ADAPTER (7) and align. Check alignment, if not satisfactory remove
and align. Insert HANDLE SCREW (2) and tighten. Press in INDEX BUTTON (1).
9
4
FLATS
ALIGNED
.3FW
FOR FITTING
LESS SPRAY
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is
properly seated on SHANK (7). Push COUPLING (9 or 9a) into TEE (6) and
attach to SPOUT SHANK (7) and tighten. Note: For product with Hand
Shower, COUPLING (9) is tightened using a 10mm (3/8”)
Hex Wrench.

Hex wench, supplied
8
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3) and unscrew
ESCUTCHEON BASE (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90° and replace.
Replace SPRING CLIP (6).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY.
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90°.
90$
SERVICE 9
5
6
HANDSHOWER INSTALLATION (Model 2555.901 series only)
TEST INSTALLED FAUCET
6
Turn VALVES "off" and attach handles.
Lift HANDSHOWER from HOLDER, direct spray into tub, lift
TRANSFER KNOB to check HANDSHOWER and HOSES for leaks.
Turn handles "off."
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4) and
LOCKNUT from underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of COUPLING (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
ESCUTCHEON (1). Install SEAL (9) and connect both HOSES (8)
and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles. To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Lift TRANSFER ROD (2) and unscrew KNOB (3). (Model 2555.901only).
Remove PLUG BUTTON (4) and remove SET SCREW (5) using 5mm hex
wrench supplied.
Lift SPOUT (1) off SHANK (6) carefully and remove RUBBER RING (7).
Unscrew SHANK SLEEVE (8) and lift TRANSFER ROD (2) from
SHANK (6). (Model 2555.901only).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (7) is properly seated in its recess at the base of the SPOUT (1).
Make certain SET SCREW (5) is properly aligned and tight so that
SPOUT (1) is locked in place.
7
5
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
34
5
5
7
8
10
9
9
11
1
2
3
4
6
7
6
8
4
3
2
1
.3FW
EverClean™ Finish Care
Instructions
American Standard’s EverClean finish
will wipe clean with a soft, dry cloth. A
soft cloth with clean water may also be
used, if desired. No additional cleaning
products are required.
DO NOT USE: Soaps, acid, polish,
abrasives, harsh cleaners, or a cloth
with a coarse surface.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002
IN MEXICO 01-800-839-12-00
LOCKNUT