American Standard CULINAIRE 4137.1 User manual

Single Control Kitchen Faucet
and Deluxe Pull-Out Spray
Installation
Instructions
M968208 REV. 1.4
Certified to comply with ANSI A112.18.1M
4137.100
Culinaire
™
CAUTION
1INSTALL FITTING WITH OR WITHOUT DECK ESCUTCHEON
Turn off hot and cold water
supplies before beginning.
Apply a bead of putty to bottom edge of ESCUTCHEON (1). Note: Installation of ESCUTCHEON (1) is optional.
Insert supply TUBES (3) and SHANK (4) through center hole of ESCUTCHEON (1) (if used) and sink.
Make certain the large O-RING (2) is properly seated in recess of faucet body.
Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD is centered.
Use a screwdriver to tighten the SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening
the screws slightly each time until all are snug to ensure even pressure.
1
2
3
4
8
PUTTY
5
6
7
9
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver Channel Locks
TOOLS REQUIRED
Tubing Cutter
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

M968208 REV. 1.4
Carefully bend COPPER SUPPLIES to meet water supply
lines using the palms of the hands to avoid kinking.
Connect HOT water supply line to left tube, and COLD
water supply line to right tube using appropriate
connectors.
2
34
FERRULE
HOT
COLD
MAKE WATER SUPPLY CONNECTIONS
Use 1/2" IPS FLEXIBLE SUPPLIES (3) or 3/8" O.D.
BULL-NOSE RISERS (4). Use adjustable wrench to tighten
connections. Do not over tighten. Be careful not to kink
copper supply when bending. Use tubing cutter to cut to
proper length.
NOTE: FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY
3
Place WASHER (3) into COUPLING NUT (1) on HOSE (2). Thread COUPLING NUT (1) onto
HAND SPRAY (4) and tighten.
Slide COUPLING NUT (1) onto HOSE (2).
Feed small end of HOSE (2) through BODY (5) so HAND SPRAY (4) rests inside SPRAY HOLDER (6).
Pull KNURLED NUT (7) up over HOSE NUT (9). Place WASHER (11) into KNURLED NUT (7).
Thread KNURLED NUT (7) onto OUTLET TUBE ADAPTER (12) and tighten.
CONNECT SPRAY HOSE
Pull KNURLED NUT (7) down over HOSE (2) (thread faces to the small end of the hose).
Put SMALL RUBBER WASHER (8) in HOSE NUT (9) and screw HOSE NUT (9) onto HOSE END (10) and tighten.
With HAND SPRAY (4) seated in SPRAY HOLDER (6), install WEIGHTS (13) onto HOSE (2) using two SCREWS (14).
Locate the WEIGHTS (13) two feet (2') from the underside of the sink deck. Tighten SCREWS (14) firmly.
11
9
8
1
7
5
3
26
4
10
2
13 14
12

M968208 REV. 1.4
Remove BUTTON (2) and loosen HANDLE SCREW (2) and pull off HANDLE (3).
Remove ESCUTCHEON CAP (4) by pulling it upward. Unscrew the three
CARTRIDGE SCREWS (5) and remove CARTRIDGE (6).
Clean inlets of CARTRIDGE (6) and MANIFOLD (7).
Reassemble CARTRIDGE (6), alternately tightening SCREWS (5). Replace
CAP (4) and HANDLE (3), check flow.
SERVICE
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Reduced flow. If the flow should gradually be reduced over a number of months,
the AERATOR may have debris in it. To clean, remove AERATOR (1) and rinse with
water to remove any debris. Turn on faucet to wash any debris out of the faucet.
Screw AERATOR (1) back to the spout. Operate faucet.
4
5
7
1
2
4
3
TEST INSTALLED FAUCET
5
6
Move HANDLE (1) down into "off"
position.
With HANDLE (1) down in "off"
position.
Turn on water supplies and check
all connections for leaks.
Operate handle up and down, in COLD
and HOT positions, to flush water lines
thoroughly.
Connect HAND SPRAY (2) to HOSE
END (4). Place HAND SPRAY (2)
back into faucet, operate HANDLE (1)
and check all connections for leaks.
Pull HAND SPRAY (2) from FAUCET (5)
and disconnect HAND SPRAY (2). Pull
HOSE (3) (HOSE should pull
approximately 2 feet) and direct open
HOSE END (4) into sink.
Check HAND SPRAY (2) operation:
With faucet on push front of
BUTTON for a broad cleansing
spray.
1
35
2
4
CHECK CONNECTIONS
FOR LEAKS
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS: