American Standard Silhouette ASME A112.19.4M User manual

G47
© 2008 AS America Inc.
CHANDLER™ AMERICAST® ISLAND SINK
• Americast® brand engineered material
• Single bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available CHO, 3 faucet hole conguration, or
less ttings deck
• Customized hole punchings available
(see page G57)
Top Mount/Undercounter:
❏ 7182.001 Center hole only
❏ 7182.803 3 hole
❏ 7182.000 No faucet holes
Undercounter Installation Order:
❏ 791003-100 Mounting Kit (consists of
cut-out templates and mounting hardware)
Nominal Dimensions with faucet hole
7182.001 and 7182.803:
419 x 381 x 216mm
(16-1/2" x 15" x 8-1/2")
Nominal Dimensions no faucet hole 7182.000:
419 x 314 x 216mm
(16-1/2" x 12-3/8" x 8-1/2")
Bowl sizes for all models:
330mm (13") wide
229mm (9") front to back
203mm (8") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Trap:
Optional Accessories:
❏ Small Wood Cutting Board: 9000.185
❏ Colander For Cutting Board: 8102.100, Color:
Revised 2/08
7182.001/7182.803
7182.000
CHANDLER™
ISLAND SINK
AMERICAST®
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

G48
© 2008 AS America Inc.
7182.001/803 Top Mount 7182.001/803 Undercounter Mount
NOTES:
* FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS
USE TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
FINISHED
FLOOR
C/L
7182.001
(1 HOLE)
*CUTOUT
NOTE
HOT COLD
2" (51mm)
OPTIONAL
FINISHED WALL
OR SPLASHBACK (3) 38mm (1-1/2)
DIA. HOLES TYP.
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
5-3/4" (146mm)
8"
(203mm)
16-1/2"
(419mm)
1/2"
(13mm)
8-1/4"
(210mm)
3-1/2"
(89mm)
DIA.
1" (25mm)
RAD.TYP. 3/4"
(19mm)
15"
(381mm)
8-13/16"
(229mm)
2"
(51mm)
2"
(51mm)
2"
(51mm)
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791003-100 FOR
UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED
AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
CHANDLER™
ISLAND SINK
AMERICAST®
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
7182.000 Top Mount 7182.000 Undercounter Mount
NOTES:
* FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS
USE TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791003-100 FOR
UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED
AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
DETAIL OF MOUNTING CLIP
(KIT No.791003-100)
BRASS
INSERT
1/2 "
(13mm)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
C/L MOUNTING CLIP
(SEE DETAIL)
7182.001
(1 HOLE)
*CUTOUT
NOTE
HOT COLD
FINISHED WALL
OR SPLASHBACK
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
FINISHED
FLOOR
2" (51mm)
OPTIONAL
(3) 38mm (1-1/2)
DIA. HOLES TYP.
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
5-3/4" (146mm)
16-1/2"
(419mm)
8-1/4"
(210mm)
3-1/2"
(89mm)
DIA.
1" (25mm)
RAD.TYP. 3/4"
(19mm)
15"
(381mm)
8-13/16"
(229mm)
2"
(51mm)
2"
(51mm)
2"
(51mm)
8-1/2"
(216mm)
C/L
*CUTOUT
NOTE
HOT COLD
FINISHED WALL
OR SPLASHBACK
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
FINISHED
FLOOR
2" (51mm)
OPTIONAL
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
5-3/4" (146mm)
8"
(203mm)
16-1/2"
(419mm)
12-3/8"
(314mm)
6-3/16"
(157mm)
1/2"
(13mm)
8-1/4"
(210mm)
3-1/2"
(89mm)
DIA.
(3) 1-1/8" (29mm)
DIA. HOLES TYP.
1" (25mm)
RAD.TYP. 3/4"
(19mm)
2"
(51mm)
2"
(51mm)
2"
(51mm)
DETAIL OF MOUNTING CLIP
(KIT No.791003-100)
BRASS
INSERT
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
C/L MOUNTING CLIP
(SEE DETAIL)
*CUTOUT
NOTE
HOT COLD
FINISHED WALL
OR SPLASHBACK
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
FINISHED
FLOOR
2" (51mm)
OPTIONAL
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
5-3/4" (146mm)
16-1/2"
(419mm)
12-3/8"
(314mm)
6-3/16"
(157mm)
3-1/2"
(89mm)
DIA.
(3) 1-1/8" (29mm)
DIA. HOLES TYP.
1" (25mm)
RAD.TYP. 3/4"
(19mm)
2"
(51mm)
2"
(51mm)
1/2"
(13mm)
MIN.
8-1/2"
(216mm)
2"
(51mm)
Revised 2/08