American Standard DXV D35107954 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
M965521 Rev. 1.6 (1/15)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
RECOMMENDED TOOLS AND MATERIALS
Thank you for selecting DXV by American Standard.
To ensure that your installation proceeds smoothly,
please read these instructions carefully
before you begin.
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Traditional Floor Mount
Tub Filler
Lever Handle
Model D35107950
Cross Handle
Model D35107954
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
Pipe cutter
Regular Screwdriver
Basin Wrench

- 2 - M965521 Rev. 1.6 (1/15)
1
COLD
HOT
2-3/4" DIA.
(68.5mm)
6"
(152mm)
6-3/8"
(160.5mm)
1/3/8" DIA.
(35mm)
MOUNTING HOLES
2-1/4"
(56mm)
28-7/8"
(735mm)
5"
(126mm)
12-5/8 "
(320mm)
11-5/8"
(296mm)
LEVER
HANDLE
CROSS
HANDLE
6-3/4"
(170mm)
30°
FINISHED FLOOR
G 3/4"
SUPPLY CONNECTION
ASSEMBLE MOUNTING STUDS
• Apply sealing tape or sealant to threads of
MOUNTING STUDS (1) as shown in illustration.
• Thread STUD ADAPTERS (2) onto MOUNTING STUDS (1).
Tighten fully with wrenches.
1
SEALING TAPE
OR SEALANT
2
ROUGHING-IN DIMENSIONS:
• For reference

- 3 - M965521 Rev. 1.6 (1/15)
ASSEMBLE FLOOR ESCUTCHEONS AND RISER PIPING
• Apply sealing tape or sealant to threads of RISER PIPES (1).
• Slide FLOOR ESCUTCHEONS (2) onto RISER PIPES (1).
• With wrenches connect the STUD ADAPTERS (3) to RISER PIPES (1).
• Tighten MOUNTING STUDS (4) to RISER PIPES (1) with HEX WRENCH (5) supplied.
2
1
2
3
4
5
SEALING TAPE
OR SEALANT

- 4 - M965521 Rev. 1.6 (1/15)
INSTALL RISER SUPPLY PIPING
• Install ESCUTCHEON SEALS (1) into groove in escutcheon base.
• Slide BRASS WASHERS (2) onto RISER PIPES (3).
• Install RISER SUPPLY PIPES (3) into mounting holes in oor.
From underside of oor install BRASS WASHERS (2) and
LOCK NUTS (4) onto RISER SUPPLY PIPES (3). Do not tighten
LOCK NUTS (4) fully.
NOTE:
RISER SUPPLY PIPES (3) are 1/2" (13mm) NPT female connection.
INSTALL BATH FILLER
• Install two SEAL WASHERS (1) into
COUPLINGS (2) if not already installed.
• Align FLOOR SUPPLIES (3) with inlets of
COUPLINGS (2). Thread COUPLINGS (2)
to FLOOR SUPPLIES (3). Do not fully tighten.
• When aligment of BATH FILLER and FLOOR
SUPPLIES are complete, fullytighten MOUNTING
NUTS (4) below oor and COUPLINGS (2)
on BATH FILLER (5).
• Tighten ESCUTCHEON SET SCREWS (6)
with Hex Wrench supplied to secure
ESCUTCHEON (7).
• Connect Hot and Cold supplies to RISER
SUPPLY PIPES (3). Connections are
1/2" (13mm) NPT female.
1
2
3
5
HOT
COLD
4
2
4
3
6"
(152mm)
1/2" (13mm) NPT female
6
7
1
2
3
GROOVE
2
2
4
4
1/2" (13mm) NPT FEMALE
SUPPLY CONNECTION
3
4

- 5 - M965521 Rev. 1.6 (1/15)
3
INSTALL FITTING BRACKET
• Insert SEAL WASHER (1) and connect BRACKET (2) to
BRACKET NIPPLE (3) on top of FAUCET. Align and tighten rmly.
• Insert SEAL WASHER (4) and connect smaller end of HOSE (5)
to outlet Nipple on side of BRACKET (2).
• Insert SEAL WASHER (6) to conical end of HOSE (5) and attach HAND SPRAY
6
5
71
4
2
TEST INSTALLED FAUCET
• Turn VALVES to "off" position.
• With handles in "off" position, turn on water supplies
and check all connections for leaks.
• Operate both handles and ush water lines
thoroughly.
• Lift HAND SHOWER (7) from BRACKET (2)
and direct spray into tub. Turn DIVERTER
LEVER (8) to SHOWER and check all
connections for leaks. Replace HAND
SHOWER (7) to BRACKET (2).
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
INSTALL HANDLES IF NOT INSTALLED
• Turn VALVE to OFF position.
• Push CROSS HANDLE (1)or LEVER HANDLE
(1a)onto VALVE STEM (2). Checkalignment
if notsatisfactory align.
• Insert HANDLE SCREW (3) and tighten.
• Press in INDEX BUTTON (4).
4
3
1
1a
2
5
6
6a CAUTION

- 6 - M965521 Rev. 1.6 (1/15)
Traditional
Floor Mount Tub Filler
MODEL NUMBERS
D35107954
D35107950
Lever Handle
Cross Handle
H960317.XXX
HOSE AND SEALS
M964607-YYY0A
COVER
M964605-YYY0A
LEVER HANDLE SLEEVE
M964600-0070A
DIVERTER
CRANK ASSEMBLY M964543-YYY0A
PLUG BUTTON &
SET SCREW
M964612-YYY0A
LEVER HANDLE KIT
M964598-YYY0A
HAND SPRAY
HOLDER
M964604-YYY0A
CONNECTOR
H960136.191
1/2" (13mm)
CARTRIDGE
(COLD)
H960001.191
3/4" (19mm)
CARTRIDGE
(HOT)
H960170.191
3/4" (19mm)
CARTRIDGE
(COLD)
H960019.XXX
LEVER HANDLE
H960104.191
1/2" (13mm) CARTRIDGE
(HOT)
M964676-YYY0A
TAPERED SLEEVE
M964611-YYY0A
CROSS
HANDLE KIT
D35107781.XXX
HAND SHOWER
M964599-YYY0A
SHOWER BASE
ASSEMBLY
M964601-YYY0A
DIVERTER
HANDLE KIT
M964608-YYY0A
SHANK ASSEMBLY
Replace the "XXX" or "YYY" with
appropriate nish code
100
144
150
POLISHED CHROME
BRUSHED NICKEL
PLATINUM NICKEL
M964706-YYY0A
METAL INDEX
BUTTON
(HOT & COLD)
M964705-0070A
PORCELAIN
INDEX BUTTONS
(HOT & COLD)