American Standard Town Square S Series User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED
TOOLS
Town Square® S
Dual Control
Widespread Lavatory Faucet
INSTALLATION
INSTRUCTIONS
7455.801
7455.811
7455.814
Certied to comply with ANSI A112.18.1M
M965900 (8/18)
Wrench
(Supplied)
Adjustable Wrench
Channel Locks
Flat Blade Screwdriver
Phillips Screwdriver
1INSTALL SPOUT CAUTION Turn off hot and cold water
supplies before begining.
1A INSTALL VALVE BODIES
Fig. A.
• Insert SHANK (1) and HOSE (2) through center hole.
• Thread LOCKNUT (3) onto SHANK (1) from underside of sink or
mounting surface.
• Align and center SPOUT (4). Tighten LOCKNUT (3).
SPOUT BASE
4
Fig. A.
Fig. B.
1
7Blue Stripe (COLD)
7Red Stripe
(HOT)
7a
7a
5
6
3
2
Fig. B.
• Remove LOCKNUT (6) from SIDE VALVE SHANKS (5).
• Insert Hot and Cold SIDE VALVE HOSES (7),
FLEXIBLE SUPPLIES (7a) into mounting holes.
• Thread LOCKNUT (6) onto each SIDE VALVE
SHANK (5) from underside of sink or
mounting surface.
• Align and center SIDE VALVES. Tighten
LOCKNUTS (6).

- 2 - M965900 (8/18)
2
• Apply a bead of putty to underside
of FLANGE (1).
INSTALL POP-UP DRAIN
2b
• Place SEAL (1) with small end facing up into TAILPIECE (2) and tighten
against DRAIN BODY (4). PIVOT ROD (3) opening in TAILPIECE (2) should
face the rear of the lavatory. Tighten LOCK NUT (5) with channel locks.
Do not over tighten.
1
2a 1
3
4
2
5
32
1
5
4
2c
• Assemble PIVOT ROD (1), PIVOT NUT (2), CLIP (3) and SEAL (4) as
shown. Hand tighten PIVOT NUT (2) Drop STOPPER (5) into drain.
(For vandal proof drain rotate stopper so PIVOT ROD (1) goes through
EYE (6) of STOPPER (5). Make connection to “P” TRAP.
• Remove one end of CLIP (3) from PIVOT ROD (1) by squeezing ends
together while sliding.
• Insert PIVOT ROD (1) into second or third hole in EXTENSION (7) and
reassemble CLIP (3). (EXTENSION (7) may need to be bent.)
• Adjust STOPPER (5) height by repositioning EXTENSION (7) and
tightening THUMBSCREW (8).
6
5
2
4
1
8
7
3
• Drop FLANGE (1) into LAVATORY
DRAIN (2). From below assemble
RUBBER GASKET (3), METAL
WASHER (4) and LOCK NUT (5).
Do not tighten.

- 3 -
5
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3).
• Operate HANDLE (1) to ush water lines thoroughly.
• Replace AERATOR (3).
CHECK DRAIN CONNECTIONS
• Fill lavatory with water. Check that DRAIN STOPPER (4)
makes a good seal and retains water in SINK.
• Release DRAIN STOPPER (4) down and check all drain
connections and “P” trap for leaks. Tighten if necessary.
CARE INSTRUCTIONS:
TEST INSTALLED FITTING
M965900 (8/18)
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
4
3
“P” TRAP
WASTE
OUTLET
2
1
4
2
3
1
SERVICE CAUTION Turn off hot and cold water
supplies before begining.
90˚ 90˚
2
3
1
4
5
8
7
5
6
Change Direction of the Handle
• Turn valves to OFF position.
• Turn off water supplies.
• Pull HANDLE (1) “UP” rmly to release from PLASTIC INSERT (6).
• Remove SCREW (3) and pull off PLASTIC INSERT (2).
• Remove RETAINING O-RING (4).
• Lift and turn STOP WASHER (5) 90˚. Replace RETAINING
O-RING (4).
• Re-install HANDLE ASSEMBLY.
To Change Cartridge:
• Remove HANDLE (1), ADAPTER (2) and SCREW (3) via
steps above.
• Remove CARTRIDGE (7) by pulling up on it after rotating
CARTRIDGE NUT (8) counter clockwise.
Aerator Clean Out
• AERATOR may accumulate dirt causing distorted and reduced
water ow. Remove AERATOR by using the AERATOR KEY
and rinse to clear any debris.
• If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.

- 4 -
M970543-0070A
SQUARE WASHER
M970460 -YYY0A
HANDLE KIT
M970596 -0020A
HANDLE KIT
WITH RED INDEX
(HOT)
7455.811/814
M953450-YYY0A
DRAIN ASSEMBLY
M964055-0070A
HANDLE ADAPTER KIT
M923840-0070A
AERATOR (1.2 GPM)
M904516-0070A
T-CONNECTOR
M970461-YYY0A
LIFT ROD & ROD
(7455.8X1)
M970472-0070A
DECK ADAPTER
M964005-0070A
CARTRIDGE KIT
M906617-0070A
MOUNTING NUT
M970597 -0020A
HANDLE KIT
WITH BLUE INDEX
(COLD)
7455.214/217
- 4 - M965900 (8/18)
Town Square® S
Dual Control
Widespread Lavatory Faucet
MODEL NUMBERS
7455.801
7455.811
7455.814
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
BRUSHED NICKEL 295
LEGACY BRONZE 278
POLISH NICKEL 013
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200