Ameriwood HOME 4716305COM User manual

- Unit can tip over causing severe injury or death.
- Anchor unit to stud in wall (if instructed to).
- Do Not allow children to climb on unit.
- Put heavy items on lower shelves or drawers.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
WARNING
Date of Purchase ___ / ___ / ___
Lot Number:
Assembly Difficulty Meter
Easy Tough
Twin Bed
Do Not Return This Product!
Contact our customer service team for help first.

Contact Us!
Helpful Hints
Do NOT return this product!
Contact our friendly customer service team first for help.
Assembly Tips
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with a R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
Tube
You
PEOPLE NEEDED FOR ASSEMBLY: 1-2
ESTIMATED ASSEMBLY TIME: 2-3 HOURS
2

Before You Start
P
Quick
Tip
Assembly
P
P
P
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
1
3
2
4
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
P
3

Board Identification
Not actual size
Headboard Upper Rail Lower Rail Side Panel
A
BC
D
Footboard Leg x2
Footboard Panel
Footboard Top
Center Support Left Drawer Front
Left Drawer Side x 4 Drawer Bottom x2
Drawer Brace x2
Right Drawer Front
EFGHI
J
L
Drawer Back x 2
O
Right Drawer Side x 4
M
K
N
4

Board Identification
Not actual size
metal bed frame
KK
MM
I
J
LL
OO
NN
A
B
C
E
H
H
G
F
D
5

(x2)
#A97020-1
rail A
x2
#A97020-2
rail B
x1
#A97020-3
center rail
x16
#A97020-4
cross bar
(x1)
#A97020-9
hex key
(x32)
#A97020-8
locking clip
(x6)
#A97020-7
1/4-20 x 5/8" bolt
(x2)
#A97020-6
1/4-20 x 1-1/4" bolt
(x2)
#A97020-5
leg
14a 14b 14c 14d
14e 14f 14g
14h 14i
14a
14a
14b
14b
14c
14d
(x1)
#A97020
bed frame
Part List
6
Metal frame parts will be packaged in its own box.
Parts not needed for this assembly:
(14e) x2 - leg
(14f) x4 - 1/4-20 x 1-1/4" bolt

7
Part List
Actual Size
Not Actual Size
(x7)
#A22570
cam lock
(x7)
#A22510
cam bolt
(x8)
#A21660
wood dowel
(x16)
#A13010
1-1/4" screw
(x8)
#A12120
7/16" screw
(x3)
#A22910
cam bolt
(x3)
#A22900
connector
(x8)
#A20640
barrel nut
(x8)
#A19170
1/4-20 x 3/8"
bolt
(x8)
#A19895
2" cross dowel
bolt
(x8)
#A22950
cross dowel
fastener
(x20)
#A11080
7/16" flat head
screw
1
23456
7
8910 11 12
(x2)
#A56770
drawer slide pkg.
(x2)
#A21520
compression
dowel
(x12)
#A11600
1-1/4" flat head screw
(x4)
#A54213
drawer bracket
(x1)
#A23100
4mm hex key
(x1)
#A23120
5mm hex key
13a 13b 13c
15
18
17
13d
19
16

8
STEP1
Proper orientation of CAM LOCK
(x5)
#A22570
1
12
(x6)
#A11080
Turn part over to attach slide
and insert cam locks.
Marked with an "R"
Marked with an "L"
13a 13c
(x1)
#A56770
1
12
12
12
E
E
1
Quick
Assembly
Tip

9
STEP2
finished edge
finished edge
finished edge
holes for attaching
metal bed frame rails.
23
3
3
2
(x3)
#A22510
(x4)
#A21660
D
D
E

10
STEP3
finished edge
(x3)
#A11080
(x1)
#A56770
13a
12
12
13a
Marked with an "L"
A
NOTE: The drawers can be assembled to be on
either side of the bed. The left side is shown. To
have the drawers on the right side, assemble the
right drawer slide on this side.
Marked
with an "R"
13c

11
STEP4
You will need to tap the connector (7)
with a hammer to fully insert. Be sure
the connector is positioned as shown
before pushing into the hole.
NOTE: The drawers can be assembled to be
on either side of the bed. The left side is
shown. To have the drawers on the right side,
assemble the left drawer slide on this side.
Marked with an "L"
Marked with an "R"
7
(x3)
#A22900
(x1)
#A56770
(x3)
#A11080
G
7
12
12
13c
13c
13c
13a

12
STEP5
finished edge
finished edge
NOTE: The drawers can be assembled to be on either side of the bed. The left side is shown. To have
the drawers on the right side, the headboard and footboard are switched each end. Refer to the notes
on steps 3 and 4.
Attach the headboard to the other end of the side panel (D).
Make sure the correct drawer slide is attached to the other side of the headboard.
(x1)
#A23100
(x2)
#A19895 (x2)
#A22950
10 11
10
10
11
D
A
E
15

13
STEP6
3
2
(x2)
#A22510
(x4)
#A21660
3
3
2
B
C

14
STEP7
finished edge
11
10
10
11
A
E
C
(x1)
#A23100
(x1)
#A19895 (x1)
#A22950
15

15
STEP8
11
10
A
BE
C
11
(x1)
#A23100 (x1)
#A19895 (x1)
#A22950
15
10

16
STEP9
11
10
(x4)
#A22950
(x4)
#A19895
(x1)
#A23100
D
B
C
G
10
10
10
10
11
11
15

17
STEP10
Notice: Do not fully tighten these bolts.
Leave loose for now.
notice hole locations.
(x4)
#A97020-7
(x1)
#A97020-9
rail A
rail B
(x4)
#A97020-1
(x4)
#A97020-2
x2
14i
14g
14a
14b
14g 14a 14b
14a
14b

18
STEP11
slots on the inside of the frame
(x2)
#A97020-3
(H14i) x1
#A97020-9
(x1)
#A97020-7
14i
14c
14g
14a
14a
14b 14b
14c
14g
14c

19
STEP12
(x1)
#A97020-9
Note: Be sure to turn the metal frame over when
attaching to the bed. The bolts (14g) from the
previous step should be facing down.
1. Attach metal frame to headboard and footboard
using eight barrel nuts and 1/4-20 x 3/8" bolts.
(x8)
#A20640
(x8)
#A19170
89
8
A
A
G
14i
8
9
9

20
STEP13
(x12)
#A13010
4
4
4
4
4
4
4
4
4
4
4
4
4
Notice: Tighten these bolts
on both sides now from step 10.
4