Ametek TELGUARD TG-PEM User manual

Quick Install Guide
TG-PEM Wiring Diagram
(zone connections not shown)
•The connection from
Telguard Power on the
TG-PEM to the DC
connection on the TG-7
or TG-7FS should be the
ONLY power supply
connection. The AC
power and battery
connectors must NOT
be used. LED8 (AC
Power) should not be
lit.
•Supervised zones utilize
2.2kΩEOL resistors (not
provided).
STEP-BY-STEP:
1. Register the TG-7 or TG-7FS
Use the dealer portal at www.telguard.com.
2. Pre-configure the TG-PEM prior to installation
Use the Power Expansion Module tab for the device registered.
3. Mount the TG-7 or TG-7FS
Complete all steps of the physical installation as outlined in the
TG-7 series manual. Do not activate yet.
4. Mount the TG-PEM
Tip: To ease mounting of TG-PEM board, pre-thread the metal bracket
using the provided mounting screws (marked in red in diagram)
•Remove top left mounting screw that holds the TG-7
series board (indicated by arrow).
•Orient bracket as shown in diagram.
•Insert bracket at an angle so that top mounting point
slides under board as depicted, and angled tab
threads through the enclosure bump out.
•Replace screw to securely mount bracket and board.
```
TG-7FS
LTE
Pre-thread using screws
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
DC STC2 STC1 TRIP BATT AC
Installing the TG-PEM inside the TG-7 or TG-7FS is simple, but watching our installation
video will get you going in no time and insure your installation is quick and easy.
Scan the QR code or visit telguard.com/pem for the installation video and other useful resources
including the full Installation Manual.
TG-7FS
LTE
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
Alarm Panel
Burglary Systems: STC1 needs to
be connected to a 24-hour panel
input zone to indicate alarm
conditions from TG-PEM. STC2
could be used to indicate TG-7
trouble conditions. Do Not Use these power
connectors when using TG-PEM.
Power from TG-PEM
TG-PEM
Panel Power (DC)
DC STC2 STC1 TRIP BATT AC
Fire Systems: STC1
needs to be connected
to a panel input zone
to indicate all trouble
conditions.

Use the three provided mounting screws to secure the TG-PEM
board onto the bracket.
5. Connect the TG-PEM to TG-7 or TG-7FS
•Make sure there are no AC or DC power sources
connected to the TG-7 or TG-7FS. Connect power and
ground from the TG-PEM terminal labeled “TELGUARD
POWER” to the terminal block on the TG-7 or TG-7FS
labeled DC and GND. Do not overtighten.
•Connect ribbon cable (provided) from the connector on
TG-PEM labeled “TO HOST” to the 3x2 6-pin header on
the TG-7 series board as shown. The dark color edge of
the ribbon cable should be oriented away from the
antenna of the TG-7 or TG-7FS.
6. Power Up and Configure
•Connect power and ground from the panel
auxiliary output to the terminal labeled “PANEL
POWER” on the TG-PEM to provide power to the
TG-PEM and TG-7 or TG-7FS.
•Complete the activation of the TG-7 or TG-7FS as
outlined in the TG-7 series manual.
•If the TG-PEM was preconfigured, it should now
be ready; otherwise, visit www.telguard.com to
configure the TG-PEM.
•When the TG-PEM is configured and ready, LED
D2 will be either solid amber (in power supply
only mode) or solid green (in power supply and
zone extender mode).
7. Connect Zone Inputs (if using)
•Temporarily disconnect the power while you
connect any monitoring sensors to the zone
inputs.
•For supervised zones, use a standard 2.2kΩEOL
resistor (not included).
•Reconnect power, allow the TG-7 or TG-7FS to
initialize, and check for proper operation.
Optional: Second TG-PEM Installation
See full Installation Manual for mounting and wiring
instructions.
REFERENCE:
LED
D1
LED
D2
STATUS
DETAILS
Off
Green
Ready, no
activity
TG-PEM is ready
Off
Off
Shut down
Power to TG-PEM is below
minimum
Any
Amber
flash
Communicator
activating
TG is being activated
Red
Green
Reportable
event
At least one enabled input is
tripped or event(s) captured
and waiting to be reported
Red
flash
Green
Event
reporting
Event(s) reporting or waiting
for response
Off
Red
flash
Bootloader
error
Device failure, contact
Technical Support
Off
Amber
Power supply
only or
Not ready
Power supply mode,
TG-PEM waiting for
configuration, or
Communicator not enabled
TO HOST TO TG-PEM D1 D2
Reset TELGUARD
POWER
POWER
PASS THRU
PANEL
POWER
DC GND
ZONE INPUTS
1 C 2 3 C 4 5 C 6 7 C 8
GND DC GND DC
```
TG-7FS
LTE
3x2 6-pin header Dark edge on right
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
DC STC2 STC1 TRIP BATT AC
56051801 –Rev A
Note: At power-up, both LEDs will be on for 3 seconds then off for 3 seconds.