AMG AMG5612 User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The infor
mation herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
1
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
AMG5612
Instruction Manual
Single Channel Video Receive Unit for a Multimode Fibre
Link
The
AMG5612
is a standalone system designed to receive one video signal over a Multimode optical
fibre.
The
AMG5612
is designed to be powered usin
g an
AMG2001
standalone power supply.
The
AMG5612
is designed to operate with an
AMG5611
standalone video transmit unit in a point to
point configuration.

AMG Systems
Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
2
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
Contents
Introduction
3
Unit Functional Schematic
................................
................................
................................
..................
3
Optical Connection
................................
................................
................................
.............................
3
Connections
4
Video Output Connection
................................
................................
................................
...................
4
Optical Connections
................................
................................
................................
...........................
4
Power Connection
................................
................................
................................
..............................
4
Front Panel Indicators
4
Power LED
................................
................................
................................
................................
..........
4
Physical Information
5
Dimensions
................................
................................
................................
................................
.........
5
Mounting Details
................................
................................
................................
................................
.
5
Removal / replacement from / to the Case
................................
................................
.........................
5
Safety
5
Maintenance and Repair
5

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Pa
ge
3
of
8
A
MG5612
Instruction
Sheet
D17078
-
02.doc
Introduction
Unit Functional Schematic
The
AMG5612
receives 1 video si
gnal
from an
AMG5611
transmit unit.
Optical Connection
The
AMG5612
connections are illustrated in the following example which shows an
AMG5611
single
channel transmit unit together with a
AMG5612
configured as a point to point system.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein i
s believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
4
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
Conn
ections
Video Output Connection
Connector
................................
............
75 ohm BNC Socket.
Output Impedance
...............................
75 ohm terminated.
Output Level
................................
........
1 Volt p
-
p nominal
Frequency Response
...........................
10Hz to 7MHz.
Optical Connections
No. of Optical Connections
..................
1 per video channel
Optical Fibre
................................
........
Multimode 5
0/125 or 62.5/125**
Connector
................................
............
SC/PC
Minimum Optical Sensitivity
.................
-
30dBm
Receive Wavelength
............................
1310nm
Optical Link Dynamic Range
...............
20dB.
**Note: the transmission distance is limited by the bandwidth of the Multimode optical fibre. The optical
data rate is 155M
bits/s, which may restrict operation to a maximum fibre length of 7km, although in
most cases the units will operate successfully over longer fibre lengths. It is advisable however for
distances greater than 7km, to have the optical fibre tested.
Power C
onnection
Connector Type
................................
...
Removable 2
-
pin, 3.81mm, Screw Terminal
Connector Partno.
................................
Phoenix 1803578
Supply Voltage
................................
.....
+12 to +15 Volts DC
Maximum Power
................................
..
1.5 Watts
Front Panel Indicators
Power LED
Power / Video / Opto
............................
Green
-
Video present & opto sync.
R/G
-
Opto sync. but no video present.
Red
-
No opto sync.
Off
-
No power applied to unit.

AMG Systems Ltd. reserves the
right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
5
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
Physical Information
Dimensions
Height
................................
..................
112mm
Width
................................
...................
170mm (excluding connectors)
Depth
................................
...................
35mm
Weight
................................
.................
600grams
Mounting Details
The AMG unit is supplied with a clip
-
on
mounting bracket which should be attached to a panel or wall
using 2 off 4.0mm screws, see diagram on page 1 for dimensions. The unit is clipped into the
mounting bracket, and is then held firmly in position.
Removal / replacement from / to the Case
Note
:
-
The AMG unit PCB is static sensitive. Handle with proper care and use normal electrostatic
discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when
handling the PCB out of the case.
To remove the PCB from the case
for example to access a Low Speed Data mode switch, remove the
2 fixing screws on the rear panel and slide the PCB sufficiently out of the case to enable access to the
switch.
To replace the PCB into the case, slide the PCB gently into the case, if nece
ssary aligning the board
with the appropriate slots.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825
-
2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:

Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.

Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice assoc
iated with optical fibre systems, please see
EN 60825
-
2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please
call your local support centre or contact:
AMG Systems Ltd.
at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone
[phone]
Technical Support
[phone]
Email
[e-mail]

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
6
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
This page is intentionally blank.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be ac
curate. No responsibility is assumed by AMG for its use.
Page
7
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
This page is intentionally blank.

AMG Systems Ltd. reserves the right to make chang
es to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
8
of
8
AMG5612
Instruction
Sheet
D17078
-
02.doc
This page is intentionally blank.